Impact Test
forceful strike to UUT determining strength and durability or detection of loose particles.
See Also: Drop Testers, Pendulum Impact, Impact Hammers, Crush, Hardness Testers, Rupture
-
Product
IEC60950 Ball Drop Impact Test Apparatus
-
Shenzhen Chuangxin Instruments Co., Ltd.
It is mainly used for mechanical strength testing equipment enclosure, test equipment enclosure should be able to ensure that the structure can be expected to withstand the operation does not produce within the provisions of the standard risk for damage to the outer surface of the enclosure will touch dangerous parts of the apparatus.
-
Product
Impact Test Apparatus
IT-50
-
Impact test is an essential physical test prescribed in many standards to test samples for mechanical shock. It is designed to perform such tests. The test is carried out to ensure that the test items have adequate mechanical strength to withstand the stresses and rough handling imposed during installation and use. It is adapted to test various types of electrical accessories such as switches, sockets, plugs, starter seats and other electrical appliances.
-
Product
Impact Test Apparatus
-
SCR Elektroniks make Impact Test Apparatus is used to test the Electrical Accessories / appliances for their mechanical strength.
-
Product
1040g Steel Impact Ball Drop Impact Test Ball
CX-B104
-
Shenzhen Chuangxin Instruments Co., Ltd.
1040g Steel impact ball drop impact test ball
-
Product
2 Inch 535g Steel Impact Ball For Impact Test
CX-B2
-
Shenzhen Chuangxin Instruments Co., Ltd.
2 inch 535g steel impact ball for impact test
-
Product
Impact Test Machine
-
JINAN PRCISION TESTING EQUIPMENT CO., LTD
Used to determine the resistance of a material or component to a rapid load under varying temperature conditions.
-
Product
Gear Teeth Hardness Tester
PHT-1840
-
This dedicated unit is designed to test gear teeth and other difficult to access applications. The 1840 is loaded with the same features found on the base 1800 version which includes memory, USB output and software for downloading to your PC. The 1840 hardness tester is capable of measuring the surface hardness of a broad variety of metals on flat and round surfaces. This instrument comes complete with a dedicated DL impact device, calibrated test block and rugged carry case.
-
Product
Drop Tester
KD 688 A
-
King Design Industrial Co., Ltd.
*PLC control, linear motor fast speed control the height setting.*Alarm warning before testing.*Light support structure decreases the test impact.*Support dropping very smooth with dual lubrication guide.*No second impact. *A data acquisition for the impact wave record (Option).*Non maintenance request for continue operation.*According to ISTA, ASTM .....etc international standard.*Equipped edge & corner holder.
-
Product
Drop Weight Impact Tester
-
The Falling Weight Impact Tester is used to perform impact tests on plastic pipes, conforming to ISO 3127, EN744 and EN1411. Test pieces are subjected to blows from a falling striker, of specified mass and shape, dropped from a known height onto specified positions around the circumference of the test piece. The true impact rate of the batch, or production run from an extruder, is estimated.
-
Product
Damped MEMS High-G Shock Accelerometers
-
Damped MEMS high-amplitude shock accelerometers represent state-of-the-art industry technology for miniature, high amplitude, DC response acceleration sensors. This series is capable of measuring long duration transient motion, as well as responding to and surviving extremely fast rise times, typical of a high-g shock event as found in explosive, gun and impact testing. Both packaged and OEM configurations are offered, to fulfill a variety of installation requirements.
-
Product
sbRIO-9235, Non-Enclosed, 10 kS/s/channel, 120 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module
781579-01
Strain/Bridge Input Module
Non-Enclosed, 10 kS/s/channel, 120 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module - The sbRIO‑9235 measures dynamic strain on all channels simultaneously, allowing for synchronized, high-speed measurements. This capability is important for applications, such as impact tests, that require comparison across many channels at a particular instant in time. The sbRIO‑9235 includes built-in voltage excitation for quarter-bridge sensors. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. Non-enclosed modules are designed for OEM applications.
-
Product
Charpy/Izod Pendulum Impact Tester
-
Qualitest offers a wide range of pendulum Charpy / Izod impact testers for tests according to the relevant test standards such as ASTM D256, ASTM D6110, ISO 179, ISO 180, as well as other DIN, ASTM, and ISO standards. These pendulum Izod / Charpy impact testers cover a range from 0.5 Joules to 50 Joules, and we can even go up to 800 Joules with the models in the Metals category. The Plastics Pendulum Izod / Charpy Impact Testers are available in a variety of models, e.g. for instrumented or non-instrumented tests, with analog or digital displays and with a range of different options especially made for your tests.
-
Product
NI-9235, 10 kS/s/channel, 120 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module
785995-01
Strain/Bridge Input Module
10 kS/s/channel, 120 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module - The NI‑9235 measures dynamic strain on all channels simultaneously, allowing for synchronized, high-speed measurements. This capability is important for applications, such as impact tests, that require comparison across many channels at a particular instant in time. The NI‑9235 includes built-in voltage excitation for quarter-bridge sensors. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety.
-
Product
Luggage Testing Machines
-
Dongguan Kejian Instrument Co., Ltd.
This machine, which is designed according to QB/T2918-2007, is applicable to the impact test of various plastic luggages.
-
Product
Air Jet Erosion Tester
AJ-1000
-
The Rtec Instruments Air Jet Erosion Tester (AJ-1000) is a state-of-the-art solution for accurate air jet erosion testing of materials and coatings. Designed to perform repeated impact tests, the AJ-1000 directs a high-velocity jet of gas carrying abrasive particles onto the sample surface to precisely measure erosion rates. This advanced tester offers closed-loop temperature control up to 1000°C, enabling erosion studies under extreme environmental conditions. With the ability to vary abrasive particle type, shape, size, temperature, and impact velocity, the AJ-1000 provides a reliable way to rank and compare the erosion resistance of diverse materials and protective coatings.
-
Product
NI-9236, 10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module
779994-02
Strain/Bridge Input Module
10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module - The NI‑9236 measures dynamic strain on all channels simultaneously, allowing for synchronized, high-speed measurements. This capability is important for applications, such as impact tests, that require comparison across many channels at a particular instant in time. The NI‑9236 includes built-in voltage excitation for quarter-bridge sensors. It also has 60 VDC isolation and 1,000 V rms transient isolation, providing high‑common‑mode noise rejection and increased safety.
-
Product
SMT Surface Mount MEMS High-G Shock Accelerometers
-
Piezoresistive MEMS high-amplitude shock accelerometers represent state-of-the-art industry technology for miniature, high amplitude, DC response acceleration sensors. This series is capable of measuring long duration transient motion as well as responding to and surviving extremely fast rise times, typical of a high-g shock event as found in explosive, gun and impact testing. Both packaged and OEM configurations are offered, to fulfill a variety of installation requirements.
-
Product
IEC60669 Pendulum Impact Tester
CX-BC2
-
Shenzhen Chuangxin Instruments Co., Ltd.
This Pendulum Impact Test Device Conforms to the standard GB2099.1, GB16915.1 and IEC60669, IEC60670 standard. To check the impact resistance performance of plug and socket electrical accessory's enclosure.
-
Product
C Series Strain/Bridge Input Module
Strain/Bridge Input Module
The C Series Strain/Bridge Input Module works with higher-channel-count, dynamic strain measurement systems. Modules can acquire measurements from up to eight channels, with compatibility options for quarter-, half-, and full-bridge sensors. The C Series Strain/Bridge Input Module is ideal for application channels requiring measurements at particular times, such as impact tests. It includes built-in voltage excitation, as well as transient isolation for high-common-mode noise rejection and improved safety.The C Series Strain/Bridge Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Hammer Impact Testing
-
EDM Modal Hammer Impact Testing provides the necessary features for a single-operator experimental modal test. The Hammer Impact GUI features an intuitive step-by-step process, allowing a user to easily go through the setup and then the testing.
-
Product
Package Testing
-
Lansmont package testing equipment is designed to perform industry standards, such as ASTM, ISTA, ISO, EUMOS and others. Our equipment is compliant with all of the most common ASTM and ISTA package testing procedures. There are individual standards that specifically reference how to perform drop testing, compression testing, side impact testing and vibration testing. In addition to those standards, there are groups of procedures referred to as distribution simulation tests, which incorporate some strategic combination of testing inputs, with the idea of simulating a typical journey through the supply chain. Some of the most common distribution simulation standards that are performed globally are published by ASTM and ISTA.
-
Product
High Impact Shock Test System
KRD16 series
-
High impact shock test system meets MIL-S-901D standard which covers shock testing requirements for ship board machinery, equipment, systems, and structures, excluding submarine pressure hull penetrations. The purpose of these requirements is to verify the ability of shipboard installations to withstand shock loadings which may be incurred during wartime service due to the effects of nuclear or conventional weapons.
-
Product
Impact Testing Machine (Izod & Charpy)
-
Suitable for Charpy & Izod Impact tests on different materials. It is based on Pendulum principle.Rigid designs of instrument frame & other parts assure minimum energy absorption during fracture which results in improved test accuracies.The highly strained & wearing parts like support blocks & strikers are of special alloy steels duly heat treated.Direct indication of Impact energy absorbed by sample on large dial -Safety guard for the user is provided.Initial potential energy for Charpy is 300 Joules & for Izod is 170 Joules with a Least Count of 2 Joules (for Analogue models) & resolution of 0.5 Joules (for Digital Model).Drop Angle of Pendulum for Charpy is 140° & for Izod is 90°.ASTM Impact Testing machine is also provided, which conforms to E-23 ASTM standard.Gauges, Tongs, Sub-zero bath, Templates, U & V Notch milling cutters are available with it (Optional).
-
Product
IEC60950 50mm Impact Test Balls
CX-15
-
Shenzhen Chuangxin Instruments Co., Ltd.
The Impact Test Ball is a specially machined ball to test impact resistance according to IEC, CSA and UL Standards. It is made of chrome-plated-steel for durability, and is fitted with an eyelet to facilitate testing for pendulum applications. Eyelet is threaded to the ball to allow attachment of a handle or force gauge. Weights are closely controlled.
-
Product
2.3KG Steel Impact Test Ball
CX-325
-
Shenzhen Chuangxin Instruments Co., Ltd.
UL858 2.3KG Steel Impact Test Ball
-
Product
Film Impact Tester
DRK136A
-
Shandong Drick Instruments Co., Ltd.
DRK136A Film Impact Tester is applicable in the precise impact resistance test of plastic films, sheets, laminated films, rubber and other nonmetal material.
-
Product
IK07-IK10 Pendulum Impact Hammer Apparatus
-
Shenzhen Chuangxin Instruments Co., Ltd.
IK07-IK10 Pendulum Impact Hammer Apparatus is desinged according to IEC60068-2-75 and IEC62262 standards. The IK07-IK10 Pendulum Impact Hammer Apparatus can be used for the mechanical impact strength test of metal enclosure.
-
Product
Hail Impact Tester
HIT
-
Hailstorms can cause severe damage to modules and collectors. Our test stand enables you to carry out tests according to international standards. The hail impact test stand uses an air-pressurized launcher that shoots ice balls representing hailstones of a predetermined size at the module or collector mounted on the support frame.
-
Product
SINGLE ENERGY IMPACT HAMMERS
-
Shenzhen Chuangxin Instruments Co., Ltd.
It’s used to test the mechanical integrity of product enclosures and check the durability of enclosures for electrical appliances of other electrical appliances and other electronic products. If damage occurs from the Impact Hammer test, accessibility probes can be used to measure the extent or severity of the damage. The Impact Hammer simulates the mechanical impact to which electrical equipment maybe subjected.
-
Product
Gear Teeth Hardness Tester
PHT-1740
-
This dedicated unit is designed to test gear teeth and other difficult to access applications. The 1740 is an economically priced hardness tester that is loaded with the same features found on the base 1700 version. The 1740 hardness tester is capable of measuring the surface hardness of a broad variety of metals on flat and round surfaces. This instrument comes complete with a dedicated DL impact device, calibrated test block and rugged carry case.
