Fiber Test Systems
-
Product
Test System
MFTS500
-
Computer Gesteuerte Systeme GmbH
The MFTS500-System is specially designed for the testing of electronic control units (ECUs). It can be configured to be used as a development or as a production tester. Every effort has been made during development and design to ensure that the system is flexible and cost effective.
-
Product
Test System Elowerk
eloZ1
-
The eloZ1 Manufacturing Defects Analyzer is an in-circuit tester of the latest generation. It reliably finds connection errors and assembly errors in electronic assemblies. The test electronics can be integrated both in table systems and in inline systems.
-
Product
Universal In-Line Test Platform
Test Platform
UniLine brings 20+ years of test & quality experience to your manufacturing floor and test automation delivers accurate results, without bias. By standardizing test, product quality improves as costs decrease. Equipment becomes understandable and manageable across departments and station support becomes simple.
-
Product
6TL24 Combinational Base Test Platform
H71002400
Test Platform
The 6TL24 is the Base platform ideal for Combinational test (ICT+FCT) in low to mid volume, high-mix electronics productions. A dual-stage pushing mechanism will allow performing both, the FCT and the ICT test, without the need of changing the test platform and with a low cost fixturing technology. To do so, the exchangeable cassette fixture must be designed with two-level probes. IN the 6TL24, the second level is reached thanks to a pneumatic actuator.
-
Product
M-TAP Fiber Test Tap
-
The Maxcom Fiber Tap (M-TAP) is a portable optical test tool designed to minimize customer downtime. Two Splitters/Taps One Portable Device 80/20 split ratio 50/50 split ratio
-
Product
Airbag Test System
-
Dongguan City Simplewell Technology Co. Ltd.
Airbag Test System by Simplewell
-
Product
Fiber Optic Measurement Systems & Sensors
-
MTI Instruments offers large measurement range and standoff distance fiber-optic measurement sensors and probes that provide ultra sensitive linear output response. Our modular (interchangeable) non-contact fiber optic sensors systems have dual channel that enables the user to make simultaneous measurements. Our fiber optic probes are designed to automatically compensate large changes in reflectivity making it possible to monitor dynamic reflectance of up to 100:1 making it ideal for measuring vibration of ultrasonic horns, modal analysis of disk drive suspension, displacement and timing of fuel injectors and lateral motion measurements.
-
Product
Sealed Beam Bulb Testing System
H710019SSL
Test Platform
EOL test for manufacturing of bulbs with LED for applications requiring to ensure watertightness: vehicles, marine, swimming pools, operating rooms, classified areas (Ex Zone), etc. The test system checks in a short time all the light and electrical characteristics of the bulb. A high precision Micro Leakage Meter also checks that there are no leaks between the environment and the inside of the bulb. The test results are recorded on the PC and can be printed on a quality control label attached to each unit.
-
Product
Autoinjector Testing System
-
Instron’s Autoinjector Testing System is designed to perform full functionality testing on a wide variety of drug delivery devices, including safety syringes and both needle shield and button-activated formats. Developed in collaboration with pharmaceutical manufacturers and CDMOs, the system captures essential performance requirements such as activation force, injection time, dose accuracy, needle depth, and click detection. It supports compliance with international standards like ISO 11608 and can be configured for integration with collaborative robots to enhance automation and throughput.
-
Product
System Test
-
Testing a complete system is very different from unit and integration test. It starts with the V model that defines the system requirements, and this needs an effective system test capability that includes both the system and the environment around it. If the system has interfaces to the outside world, communications links or human control, these interfaces have to be tested.
-
Product
Single Mode Fiber Test Kit
KI-TK077
-
Single mode fiber test kit for low to medium test volume on SM and MM systems.
-
Product
IQC Test Systems
-
Signalysis has worked with many Tier I and Tier II Automotive sub-suppliers to provide production test systems. Below are some examples of our systems; we have also supplied systems for wiper motors, axles, door panels, window mechanisms, and many other interior components.
-
Product
Automotive Test System
LABCAR
-
The LABCAR product family comprises software, hardware, and models suitable for integration into tailor-made testing systems that fit perfectly into existing processes. Deployable from the earliest to the latest phases of development, the LABCAR family provides for efficient verification and validation of embedded systems and software.
-
Product
Brake Test Systems
GIANT Evo
-
The GIANT Evo is an extension of the well-proven GIANT product portfolio and has been developed to suit the growing demands and needs of the current and future brake markets. Covering the market segments from mini and compact cars to medium sized SUVs as well as large vehicles, this brake testing machine forms the base of HORIBA’s inertia brake dynamometers portfolio. All components are specifically tailored to the needs of the passenger car market segment.
-
Product
Test Automation System for Emission Testing
STARS VETS
-
STARS VETS is a Vehicle Emission Test System application available with the STARS Automation platform for chassis, engine and powertrain dynamometers. The application provides test cycle execution, emissions equipment control, results calculation and reporting in compliance with the different legislative standards throughout the global regions. Its flexible design offers a wide range a customization, and it addresses the various requirements for R&D, COP and certification testing.
-
Product
Vibrator Test System
Sandwich Box Kit
-
"Gold standard” for vibrator tests provides more information than radio, wireline similarities or internal analysis. Other forms of vibrator QC use the vibrator controller accelerometers to measure vibrator motion. The Sandwich Box system includes external accelerometers which are used to independently record vibrator motion, thus providing a check of the whole vibrator system including the accelerometers.
-
Product
Mezzanine System
5033
System
ECM P/N 5033 provides eight channels of RS485 / RS422 I/O. The 110 ohm termination for each channel is enabled or disabled in software. Disabling termination saves power by eliminating unneeded or redundant termination. Speeds of up to 20 Mega bits per second are possible, but this design also features a 250K bits per second slower edge rate mode. The 250K bit mode is valuable when EMI is more of a concern and throughput is not important. All channels power up as inputs with the outputs disabled.
-
Product
Switchgear Test Systems / Circuit Breaker Testing
-
ACTAS test systems provide precise information as to the condition of the chamber and drive unit without requiring them to be opened. The sheer number of parameters to be determined, the wide variety of different types of switchgear equipment in use and the harsh environmental conditions encountered during on-site tests place extreme demands on test equipment.
-
Product
Raptor Primary Test System
-
The Raptor system consists of a main ‘master’ unit and a number of optional units that enable the execution of virtually any commissioning or routine testing jobs on the primary equipment of medium and high voltage electricity installations.
-
Product
Battery Testing Systems
-
The CT2001 series Battery Testing Systems are designed for energy storage materials research and battery test. The eight channels are independently programmed and controlled by the computer. The Current ranges are from 1 mA to 5 A and Voltage ranges from 2V to 15V. Each testing system is specifically built for customer needs.
-
Product
Multi-Wafer Test & Burn-in System
FOX-XP
-
The key features of the new FOX-XP test cell that contribute to the cost-effectiveness of the solution include the ability to provide up to 2,048 "Universal Channels" per wafer, which allows the system to test all the devices on the wafer in parallel. The new "Universal Channel" architecture allows any channel to be any function (I/O, Device Power Supply (DPS) or Per-pin Precision Measurement Unit (PPMU)). This enhanced architecture now allows customers to perform per pin parametric testing, more extensive digital pattern test with deeper data stimulus / capture memory (32M per pin), and deeper scan (768M) optimized for BIST/DFT testing.
-
Product
Circuit Breaker Test System
TDR900
-
It operates and records a circuit breaker’s contact timing, motion, velocity, main contact engagement & synchronization, trip and close coil initiation and currents.
-
-
Product
Airframe Electrical Power Systems
System
Rely on Astronics CorePower® airframe electrical power systems, where solid-state technologies deliver highly efficient, clean power that improves aircraft operation through weight and system wiring savings.
-
Product
Benchtop Test System
300 Series Benchtop ATE
-
The Circuit Check 300 Series benchtop ATE Test Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 300 Series Benchtop ATE, test procedures can become automatic, with test steps and go/ no-go limits easily programmable in common tabular form. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
Product
Electric Motor Test Systems
-
Electric Motor Test Systems feature our highly successful water brake dynamometer which is used as an electric motor loading device.
-
Product
Military Test Systems
-
Santa Barbara Infrared is the leading supplier of sophisticated, integrated, multi-function E-O test systems used by the military in laboratory, factory, depot and field test environments. Each of these systems are built to specific requirements and utilize SBIR’s extensive design and test capabilities, core technologies and knowledge of the unique military applications. SBIR specializes in providing complete solutions with integrated hardware and software resulting in robust and easy-to-use systems.
-
Product
Optical Fiber Cable Testing Equipment
-
Optical fiber consists of a core and a cladding layer, selected for total internal reflection due to the difference in the refractive index between the two. In practical fibers, the cladding is usually coated with a layer of acrylate polymer or polyimide. This coating protects the fiber from damage but does not contribute to its optical waveguide properties. Individual coated fibers then have a tough resin buffer layer and/or core tube(s) extruded around them to form the cable core. Several layers of protective sheathing, depending on the application, are added to form the cable. Rigid fiber assemblies sometimes put light-absorbing ("dark") glass between the fibers, to prevent light that leaks out of one fiber from entering another. This reduces cross-talk between the fibers, or reduces flare in fiber bundle imaging applications Optical fibers are very strong, but the strength is drastically reduced by unavoidable microscopic surface flaws inherent in the manufacturing process. The initial fiber strength, as well as its change with time, must be considered relative to the stress imposed on the fiber during handling, cabling, and installation for a given set of environmental conditions. There are three basic scenarios that can lead to strength degradation and failure by inducing flaw growth: dynamic fatigue, static fatigues, and zero-stress aging.
-
Product
Functional Test Systems
-
Acculogic offers commercial functional test systems for a broad range of manufacturing test applications, including automotive and military-aerospace.Designed for production testing, our solutions are optimized for throughput, reliability, repeatability, and cost
-
Product
MEMS Test System Development
-
olidus Technologies’ can design and build a test system customized for your exact needs, using our own or off the shelf components:Custom MEMS Test Systems. We can integrate and assemble test equipment and handling systems to fit your requirements. Custom MEMS Test Software. We can write custom software for device-specific calibration and testing, interfacing various instruments and handling systems, or create a customized GUI. We can also adapt our standard STI Test Software to work on your hardware system.
