Timers
mark time.
See Also: Time, Time Interval, GPS Time, Time Reference, Time Code, Time Domain, Time Standards, Timing, Time Interval Meters, Counter / Timers
-
Product
Stopwatches + Timers
-
Sper Scientific professional laboratory stopwatches and timers use only highly accurate quartz crystal movements. All models are available with an N.I.S.T. traceable Calibration Report.
-
Product
Handheld Circuit Breaker And Timer Analyser
CAT-H Series
-
The operation of the breaker can be initiated in different ways (e.g. from a control room, by a local breaker or externally by a test device) depending on the test conditions. Various time measurement triggers are available to record a measurement under a different test condition:*Coil control channel*Continuous current clamping channel*DC voltage channel
-
-
Product
Digital I/O Board, 64 Optically Isolated Digital I/O Channels,, 5V
APCI-1564-5V
-
*32 digital input channels, 5V, incl. 16 interruptible*32 digital output channels, 5V, 500 mA / channel*Optical isolation 1000V*Input and output filters*Watchdog, timer*After power/ON the outputs are reset to ì0î
-
Product
Isolated RS-422/485 Communications and Watchdog Card
WDG-SIO
-
This multifunction card contains a Watchdog Timer, an RS422/485 Serial Communications port, and an internal Temperature Alarm. The WDG-SIO is a full-length card that installs in “long” expansion slots of IBM PC/XT/AT and compatible computers. The following paragraphs describe functions provided by the WDG-SIO card.
-
Product
Power Management & MMI Module
H73000700
Interface
This module, named “6TL-MMI”, is designed to be the interface between an operator and a SYSTEM as well as being a metered power distribution unit (PDU) for it. The module is providing also safety controls, data bus interfaces, temperature control and timers. The 6TL-MMI is suitable for any ATE, and specially for those based on CAN bus controlled devices, because in addition to the above functionalities, this module is also providing galvanic isolation up to 1500V for the CAN bus. This isolation will block potential disturbance towards the DUT.
-
Product
16 SE Or 8 Diff. Input Channels, 4 Analog Output Channels, PCI Express
APCIE-3121-16-4
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
Product
PXI Switch - 24-CH 2-Wire Multiplexer Module
PXI-7921
Matrix Switch Module
ADLINK PXI-7921 is a relay multiplexer which consists of 24 2-wire relays (DPDT, 2 Form C). As a multiplexer, the PXI-7921 provides 48x1 1-wire, 24x1 2-wire and 12x1 4-wire configurations. Users could choose one of the configurations by software. PXI-7921 typically connects one instrument, such as a DMM, a digitizer or a signal source, with many points which need measurement or excitation. The contact position of the relays can be changed either by direct software commands or by following the instructions previously stored in the on-board scan list. The scan list advances upon the trigger from external measurement devices, such as a DMM. The scan list could also advance when the scan-delay timer expires. In the PXI-7921, PXI trigger functions are supported and software programmable. Multiple modules can therefore be synchronized without additional field wiring.
-
Product
Custom Energetics
-
Excelitas has extensive experience with designing, manufacturing, and testing a wide range of energetic components including actuators, detonators, initiators, and timers. The products are manufactured to precise standards enabling high reliability and consistency from device to device. The initiation mechanisms include exploding foil initiators (EFI), exploding bridge wire (EBW), and laser initiators. Detonators, actuators, and timers are manufactured and tested as build-to-print products for the NNSA.
-
Product
x1 PCI Express System Timer
SKU-048-01
-
The x1 PCI Express System Timer uses a hardware clock to synchronize IP signals. This hardware-based solution provides accurate clock timing for Asterisk® open-source PBX software.The Timer supports variable clock timing intervals. You can configure the clock interval during startup. Currently, the x1 PCI Express System Timer supports clock intervals ranging from 1ms to 64ms.
-
Product
PC/104 Plus Watchdog Timer Status Monitor
P104-WDG-CSMA
-
This multifunction card contains a watchdog timer used to monitor the operation of your application program and operating system to initiate a system reset in case of a lockup. It can also monitor and control a variety of system hardware parameters. Three models with increasing features are available.
-
Product
8 SE Or 4 Diff. Input Channels, 4 Analog Output Channels, PCI Express
APCIE-3121-8-4
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
Product
Lacquered Digital I/O Board, 64 Optically Isolated I/O Channels, 24V
APCI-1564-LAC
-
*32 digital input channels, 24V, incl. 16 interruptible*32 digital output channels, 24V, 500 mA / channel*Optical isolation 1000V*Input and output filters*Watchdog, timer*After power/ON the outputs are reset to ì0î
-
Product
DC - 400 MHz PC-Based Timer Interval Analyzer
-
GuideTech’s GT658PCI is an ultra-fast, high resolution, DC – 400 MHz Time Interval Analyzer (TIA), ideal for most PC-based lab bench (timing) test applications. What makes the GT 658 superior to traditional counters is analogous to the difference between volt meters & digital scopes. While both measure voltage, the scope provides much more information about the dynamics of the signal. This is because our patented TIA substantially increases measurement speed, and the measurements are displayed as afunction of time. All of these features, along with the benefit of ‘continuous time correlation to a common reference between all measurement time stamps,’ enable our TIAs to make measurements that weren’t previously possible with traditional counters.
-
Product
Single Channel Programmable DC Power Supply
IT6800A/B Series
-
IT6800 single channel programmable DC power supply (180W-216W) with resolution 1mV/0.1mA, users can adjust the voltage/current stepping by pressing the left and right keys to moving the cursor and programs by the front panel. OVP/OTP protection. IT6800 supports timer function and their built-in RS232 and USB communication interfaces offer you a convinience testing experience.
-
Product
RH850 Family (Automotive only)
RH850/E1x
-
RH850/E1x microcontrollers are ideal for powertrain applications, with built-in hardware for knock control such as delta-sigma A/D converter, Digital Filter Engine (DFE), Advanced Timer Unit (ATU-IV), and Autonomous Pulse Adaptor (APA), and engine control such as fuel injection control.
-
Product
Arc Ingintion Tester
-
The product is designed to carry out Arc Ignition Test as per IS/IEC 60947-1 Clause 8.2.1.1.2 (material used for electrical products). The adjustable current source is 230V AC @ 33A. The load is adjusted to get 32.5A at 0.5 power factor. Included on control unit are Digital Voltmeter, Digital Ammeter, Digital Power Factor Meter and Micro Controller based programmable Sequence Timer with LCD display for display & setting. The arrangement is made to mount the test piece with electrodes as per the specification given in the standard.
-
Product
Pico-ITX SBC With Intel® Atom® X5-E3940 Processor, DisplayPort, LVDS, 2 GbE LAN And Audio
PICO319
-
The PICO319 is powered by the onboard Intel® Atom® x5-E3940 quad-core processor. The noise-free pico-ITX motherboard offers combinations of ruggedness, high computing capabilities and enhanced graphics capability in an extremely compact size of only 100 x 72 mm. Moreover, the board features 12V DC power supply input with AT Auto Power On function. A dual-display capability is available through DisplayPort and 18/24-bit single/dual channel LVDS ports. For extensive storage needs, this compact embedded motherboard has one M.2 Key B slot (22 x 42 mm or 30 x 42 mm) for SATA or PCIe x2 SSD card and one half-size PCI Express Mini Card slot in support of mSATA. The Intel® Atom®-based pico-ITX board comes with rich I/O connectors, including two USB 2.0 ports, two USB 3.0 (USB 3.1 Gen1) ports, one RS-232/422/485 port, one RS-232 port, one HD Codec audio, and 4-channel digital I/O. It also supports SMBus that is compatible with I2C for smart battery support. The PICO319 offers watchdog timer and hardware monitoring function for reliable operation.
-
Product
Coil Analyzers & Power Supplies
-
Coil analyzers and power supply units are portable and lightweight devices intended for use in harsh switchyard and industrial environments. The typical application is switchgear and circuit breaker testing when substation battery is not connected or available. An advantage over substation battery is enabled testing in under-voltage and over-voltage conditions. Furthermore, the stable voltage outputs with a very low ripple (<0,5%) enable an analysis of the coil and motor current graphs recorded with circuit breaker analyzers from different vendors.SAT40AD, POB30AD, and POB40AD are unique devices in the market due to their dual purpose:Power supply for coils and spring-charging motorsTesting circuit breaker’s coils, motor, and auxiliary circuitAll DV Power coil analyzers and power supply units have four separate outputs for opening and closing coils.SAT40AD has two powerful motor outputs (AC and DC) which can withstand up to 40 A inrush current.POB30AD and POB40AD have DC motor output rated up to 30 A and 40 A respectively. With the use of motor outputs, POB and SAT can also be used as a power source or a temporary battery charger.SAT40A II series instruments can be controlled via PC. The DV-Win application software is used to control both SAT and CAT (Circuit Breaker Analyzers & Timers) devices at the same time, making a unique test system for switchgear and circuit breaker testing.
-
Product
PXI Switch - 16-CH General-Purpose SPDT Relay Module
PXI-7901
Relay
ADLINK PXI-7901 is a general-purpose (GP) switch module implementing 16-CH independent single-pole double-throw (SPDT) relays (1 Form C). PXI-7901 can connect one input to one output and be used as signal switching and routing for measurement system or ATE. Thanks to its high switching capacity, PXI-7901 can also be used to turn on or turn off devices such as motors, fans, heaters, and lights. The contact position of the relays can be changed either by direct software commands or by following the instructions previously stored in the on-board scan list. The scan list advances upon the trigger from external measurement devices, such as a DMM. The scan list could also advance when the scan-delay timer expires. In the PXI-7901, PXI trigger functions are supported and software programmable. Multiple modules can therefore be synchronized without additional field wiring.
-
Product
Circuit Breaker Analyzer
CAT Standard Series
-
The CAT Standard series circuit breaker analyzers & timers are stand-alone or a PC-controlled digital instruments for circuit breakers condition assessments. The timing channels record closing and opening of the arcing, resistor, and auxiliary contacts. CAT Standard series records graphs of both, trip and close coil currents and displacements of the HV and MV circuit breaker moving parts. The main contact channels can also measure the resistance value of the pre-insertion resistors (if present in the circuit breaker). Test results can be downloaded to a USB memory stick or saved to internal memory. The CAT Standard series internal memory can store up to 500 test results (numerical and graphical data). Test results can also be printed on the 80 mm (3.15 inch) thermal printer (optional accessory) in tabular and graphical form. CAT Standard series provides an easy selection of different operational modes:
-
Product
Venturi Flow Measurement Trainer (UITM-22)
-
Unitech Scales And Measurements Pvt. Ltd
UNITECHS venturi flow measurement trainer comprises of an Venturi meter fitted between the piping. A small FHP pump is used to circulate the water through the piping. Pressure ports brought out from the Venturi meter are connected to a U tube mercury manometer to measure the pressure difference. Collecting tank of capacity 5 liter is provided with graduations to measure water level. Digital timer is fixed to calculate the flow rate. Flow can be controlled using a manual control valve. The complete setup is mounted on a table top model.
-
Product
Circuit Break Timer Test Set
PME-500-TR
-
Before developing the system or equipment for the testing of a circuit break timer for distribution, the application information was obtained by consulting various users of this type of timer for circuit breaker. The customers consulted were from private service and maintenance companies, large industries, and of course from the Utility companies. It is essential to receive first hand information of the actual requirements and needs of each of these customers who are making these types of tests and then make a detailed study of the various alternatives offered by different manufactures of this type of circuit breaker timer.
-
Product
Digital Multimeter Instrumentation
-
Measurement instrumentation includes counter / timers, DMMs, digitizers, and RF power analyzers. These products are offered in PXI, PCI and ISA bus formats.
-
Product
Timers
-
ST offers industry-standard and low-power timers, in single and dual versions. These are highly-stable monolithic circuits, generating accurate time delays or oscillations. The industry-standard frequency generators are circuits designed in bipolar technology, while the the low-power frequency generators are designed in CMOS technology.
-
Product
Modbus-RTU I/O Modules
-
Sophisticated watchdog timer functions allow the application to define the module's failsafe output state. The watchdog timer invokes the failsafe condition when communication between the host and module exceed a duration specified by the application. For further security, a second hardware watchdog timer monitors the microcontroller for failed operations or a "lock-up" condition and automaticaly resets the unit.
-
Product
CPCI Based 486DX4 Board
MS 1501
-
- CPCI/PXI Bus Interface, 6U form factor- Watchdog Timer- Hot Swap Facility- PCI Bus Rear IO Expansion for External Bus Interface- Debugging Monitor interface through RS232- JTAG interface for 486 for boundary scan test- Power Source through the CPCI connector J1 (±12V, +5V, 3.3V)- 1Mbytes of Dual Port RAM, 256Kbytes of STATIC RAM- 1MBytes of FLASH PROM- RS232, RS422 Serial Interface- Intel 486DX4 operating at 100MHz frequency at the core- Driver interface for Windows2000/XP/VISTA and LINUX/RT LINUX OS
-
Product
8 SE Or 4 Diff. Input Channels, 8 Analog Output Channels, PCI Express
APCIE-3121-8-8
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
Product
MAGNA Series "Large Digit" Elapsed Timers
Models TIM4 & TIM6
-
4-digit model (TIM4) with MM:SS or HH:MM display, or 6-digit model (TIM6) with HH:MM:SS display. Large-digit displays with a digit height of 2.2" (57 mm), 4.0" (102 mm), 5.7" (144 mm), 7.9" (200 mm), or 11.0" (280 mm) for long viewing distances. Optional relays and data I/O. Choice of display brightness and cases for indoor or outdoor mounting.
-
Product
Intelligent 16 Bit Data Acquisition
CPCI-AD16
Data Acquisition Module
The CPCI-AD16 module provides a 3U high performance data acquisition subsystem. The Local DSP can be used to simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digitalfiltering, etc. Application software can be downloaded to the DSP via the CPCI interface. Instrumentation amplifiers provide over-voltage protection, gain and filtering on a per channel basis. Internal scan and trigger clocks are derived from either the CPCI bus clock or the local DSP clock. Dual 32 bit timers can programmed to pace the acquisition process. The CPCI-AD16 can also accept external scan and trigger signals from a front panel connector.
