Glow Wire
evaluates flammability of a material due to circuit overload.
See Also: Flammability Test, Needle Flame
-
Product
PXI Pull-Thru Adapter, Wired, QuadraPaddle, 68-Pin Male VHDCI
510140132-1
Pull-Thru Adapter
PXI Pull-Thru Adapter, Wired, QuadraPaddle, 68-Pin Male VHDCI
-
Product
Wire Harness Tester
NX Pro
-
The Dynalab NX Pro Wire Harness Tester is a low-cost, feature-packed, stand-alone continuity tester with a maximum capability of 512 test points. The flexibility of the NX System allows each program to perform multiple tests, display custom messages or sounds, and analyze the results of a test or an input to "decide" which operation to perform next. The NX Pro Tester has 1.3Mb memory capacity for program storage and is compatible with Printers, Scanners, and all other Dynalab NX System accessories.
-
Product
Bespoke Wire Rope Solutions
-
Wire ropes with customized end fitting, or MS Standard Wire Ropes.
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, PXI 160 Pin DIN
510140311
Pull-Thru Adapter
Pull-Thru Adapter, Wired, QuadraPaddle, PXI 160 Pin DIN
-
Product
Gauge Type T Thermocouple Wire
W-TW-44
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Gauge Type T Thermocouple Wire
W-TW-36P2
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Male Adapter, .025" Square Post for Wire Wrap
610138118
Signal Contact (Receiver)
Primary mating contact 610138200. (May mate with other Twin Female contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
Product
Wire Crimp Pull Tester (Motorized)
WT3-201M
-
The WT3-201M motorized wire crimp pull tester is designed to measure pull-off forces of up to 200 lbF [1 kN] for wire and tube terminations. The tester conforms to numerous UL, ISO, ASTM, SAE, MIL, and other requirements for destructive testing. Non-destructive testing is also possible, such as pulling to a load or maintaining a load for a specified period of time, as per the requirements of UL 486A/B. Programmable pass/fail limits with red and green indicators and audio alerts help identify non-conforming samples.
-
Product
Non-destructive Eddy Current Testing of Long Products such as Tubes, Rods, Wire, and Profiles
DEFECTOMAT® Product Familiy
-
Foerster Instruments, Incorporated
The DEFECTOMAT systems by FOERSTER were specially developed for quality testing and process monitoring of long products. From hot testing to all bright steel processing steps, the surfaces of semi-finished products made from austenitic, (non) ferromagnetic metals can be tested for defects. The DEFECTOMAT systems operate in a contactless and non-destructive manner in accordance with the eddy current method and are used for detecting short defects, such as holes or localized defects and transverse defects. The systems detect defective materials fully automatically and reliably. Defects can be marked, classified, and automatically discarded. the test speed of up to 150 m/s facilitates 100% testing, even at high production speeds. The systems benefit from low operating costs and frugal energy consumption as well as low maintenance costs, few wear parts, and low use of materials.
-
Product
PXI Pull-Thru Adapter, Wired, QuadraPaddle, to 78 Pin Female D-Sub
510140194
Pull-Thru Adapter
PXI Pull-Thru Adapter, Wired, QuadraPaddle, to 78 Pin Female D-Sub
-
Product
Heavy Duty Circuit Tester with 12' Retractable Wire & Battery Clip
27300
-
Features an extra long wire that stretches up to 12 feet for use, then automatically retracts. Quickly and easily check electrical circuits and accessories on 6 and 12 volt systems. Great for use on cars, trucks, boats, trailers, motorcycles, airplanes and snowmobiles. Heavy duty ground clip with insulator. 3 1/4" standard length probe
-
Product
LAN and telephone wiring testers
-
Measurement and analysis instruments for the deployment of telephony networks, Ethernet, and generally telecommunications networks via copper cable.
-
Product
Drawing Die And Wire Measurement
Drawing Die Inspector DDI
-
Optik Elektronik Gerätetechnik GmbH
Special microscope setup for visual inspection of wire drawing dies.
-
Product
Signal, Module, ID, CASS, 210 Position, Discrete Wiring
510114106
ITA Module
Module, ID, Cass, Signal, 210 Positions, Discrete Wiring
-
Product
3 Wire (Digital) Earth Resistance Tester
2120 ER
-
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● 0Ω adjustment.● Battery operated.● Data hold function.● Low battery indication.● Calibration performed with supplied test leads.
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, 90 Series, 2 VHDCI Male
510140158
Pull-Thru Adapter
Pull-Thru Adapter, Wired, QuadraPaddle, 90 Series, 2 VHDCI Male.
-
Product
Gauge Type T Thermocouple Wire
W-TW-40P
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Wire Damage Test Device For Pull Testing
IEC60884 FIG11
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 FIG11 Wire damage test device for pull testingThe wire damage test device is a special test instrument designed and manufactured according to the requirements of IEC884 Figure 11, , etc. It is mainly used to judge whether the screw-clamp type terminal is in design and structure.
