Showing results: 196 - 210 of 416 items found.
-
ES4640 -
ETAS GmbH
The ES4640 Connector Box offers a standardized wiring and connectivity for HiL testing systems in the powertrain domain. Its front panel provides connectors for the ECU, CAN bus communication, on-board diagnostics, and LEDs for ignition and injectors. Its rear panel connects loads, failure simulation, and other components. Sample applications of the ES4640 are closed loop HiL systems for 8 cylinder gasoline and diesel engine ECUs.
-
Hilkar
Test Laboratory Reactors are designed for high voltage and high power test laboratories. They are designed to withstand the most extreme electrical service conditions during test periods. Design techniques are implemented in accordance with the most demanding service conditions. These reactors are used for various purposes in test laboratories such as current limiting and synthetic testing of circuit breakers, capacitor testing, artificial line simulation etc.
-
Bloomy Controls, Inc.
The Airframe Environmental Control System Test Platform provides a hardware-in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of cockpit and cabin environmental control systems for airframes. The system simulates a military or commercial airframe cabin, including sensors and actuators from the control system and the passengers. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation systems.
-
National Technical Systems
Transportation simulation testing involves the application or simulation of environments found in the transport of goods and equipment. These environments may include vibration, drop or shock, temperature, loose cargo or bounce, as well as other dynamic or climatic environments. Products and equipment are usually tested in the “shipping” configuration which means they would be packed in the default shipping container or transit case during the test. However, some items may also be tested in an unpacked state if there is an expectation that they might frequently be transported in that manner. Tests are performed not only to test the effects of transport on the product itself, but also to test the adequacy of shipping container design and the interaction between product and container during shipping. There are a number of possible modes of transport for any given item subject to shipping.
-
BMS HIL -
Bloomy Controls, Inc.
The BMS Hardware-in-the-Loop (HIL) Test System is a high performance platform providing all necessary input signals used for battery pack simulation. A real-time operating system executes complex cell and pack models commonly used for BMS algorithm development and firmware regression testing.
-
EA-SERIES -
Envisys Technologies
A-Series Altitude Chambers offering the best of the unique and uncompromised features at competitive prices. Ideal for choosing your best suit for variable product sizes from the available range of standard sizes for meeting your test application for temperature, RH and low-pressure simulations of wide ranges. High performance & inherent reliability guaranteed for continuous testing of your products. These chambers can be easily movable on the wheels to convenient places and easy to maintain.
-
PAS-F -
Intepro Systems
The Intepro PAS-F Series is a broad line of programmable three phase output regenerative utility grid simulator products. With power levels ranging from 45kVA up to 1.6MVA, the series is capable of testing the largest of dispersed energy inverters. The PAS-F combines utility grid simulation with regenerative bi-directional AC source controlled power that is capable to both source and sink full current from the equipment under test (EUT).
-
Yangzhou Power Electric Co., Ltd
High current test systems are used to test the thermal stability of equipment and components. The test system induces a current in the test object causing it to heat up.The system can perform the heat cycle testing for power cables type test and pre-qualification test according to IEC 60840, and IEC 62067 etc. Based on pre-qualification test needs, test system is divided into two parts: test sample loop and simulation temperature loop.
-
Bloomy Controls, Inc.
The Bloomy Simulation Reference System provides a hardware in-the-loop (HIL) test environment for dynamic, closed-loop testing of many aerospace and transportation control systems. The reference system integrates the computing, I/O, and software components needed for standalone use or to form the basis of a more complex test system.
-
CAST Navigation
The CAST-CRPA Simulation Systems provide a precise, coherent, and repeatable GNSS RF signal “wavefront”, that is a perfect solution for testing phased array, or “CRPA” antenna systems, in a laboratory environment. The system generates a complete set of RF signals for each antenna element, which are referenced to the phase center of the antenna manifold. In addition, the CAST system allows users to add interference and IMU signals that can also stimulate EGI’s and a wide range of modernized navigation devices.
-
Altair Engineering, Inc.
Altair model-based development (MBD) tools drive fast development for smarter connected systems. Altair customers simulate complex products as systems-of-systems throughout your entire development cycle from early concept design to detailed design to hardware-in-the-loop testing (HIL). Explore more by combining mechanical models with electrical models (in 0D, 1D, and/or 3D) to enable multi-disciplinary simulation and leverage automatic code-generation for your next generation embedded systems.
-
61800 Series -
Chroma ATE Inc.
The increased demand for Distributed Energy Resource (DR) products such as PV Inverter and Wind Energy systems, have increased the demand for regulation test standards to insure proper operation and safety of on-grid products. Manufacturers testing to prove compliance, need test equipment that can simulate and measure and test their products. Chroma’s 61800 family of Regenerative Grid Simulators provide a full 4 quadrant, regenerative, grid simulation for compliance, safety, and product verification testing
-
Testhouse Ltd
Is your software working the way it is intended to? Will it work in the real world as it does in simulations? Is the code really executing as per its outlined specifications? Do various parts of the application interact as planned? Will users find the application functioning as per their requirements or will they get lost in the flow? Functional testing answers all these questions and more:- Tests your application against its intended output parameters to make sure it works the way it is meant to.- Tests if the functions of the application are working as intendedUnderstand if various parts of the application are interacting as planned.- Check if the user navigation is simple, free-flowing, and friction-less.- Functional Testing ensures optimum quality for content, design and user experience.
-
40-190B-002 -
Pickering Interfaces Ltd.
The Dual Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Polaris Networks
The C-SGN Emulator combines the MME, SGW, and PGW functions, simulating the optimized EPC network required for CIoT. As part of the NetTest suite, the C-SGN Emulator creates an end-to-end lab environment for testing functions and features that characterize enhanced Machine Type Communication (eMTC) and Narrow Band Internet of Things (NB-IoT) implementations. In order to reduce complexity in the setup of a test environment, it also supports simulation of SMS Central Function (SMS-SC) and the Service Capability Exposure Functions (SCEF).