Switching
Controls consisting of a mechanical or electrical or electronic device for making or breaking or changing the connections in a circuit. (www.cogsci.princeton.edu)
See Also: Switching Matrix, High Voltage Switching, Switching Matrices, Multiplexers, General Purpose Switch
-
Product
PXI Dual 6 to 1 RF Multiplexer 6GHz 50 Ohm SMA Terminated
40-881-002
Multiplexer Module
The 40-881 is a 50 Ohm 6 to 1 6GHz multiplexer available as a single or dual MUX in one and two PXI slots respectively. The 40-881 exhibits low VSWR characteristic over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensure a long service life with no wear out mechanism, making the 40-881 ideal for ATE systems requiring frequent and fast operating RF switching with no contact bounce.
-
Product
Chassis - Controls up to 16 8x1 Modules, 32 4x1 Modules or Mixtures or 8x1's, 4x1's, 2x1's and 2x2 Modules in Any Combination or Configuration up for up to 128 Relay Drives
CXM/128-MF
Chassis
These Chassis controls up to 16 8x1 modules, 32 4x1 modules or mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 128 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional. Chassis is available with sink or source relay drivers from + 5 to + 28 volts, ot TTL drivers for programmable attenuators. Firmware commands for Fade and Handover for WiFi, Cell Phone and WiMax labs. Fully custom systems built with little to no NRE.
-
Product
PXI 4 Slot BRIC 264x4 2-pole (6 sub-cards)
40-562A-022-264X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-010-012
-
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
LXI Microwave Multiplexer, SP4T, 4-Bank, 40GHz, 50Ω, SMA-2.92, Terminated
60-803-504
-
Our 60-803-504 is a 4 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 40GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
Low-leakage Switch Mainframe
E5250A
Mainframe
The Keysight E5250A low-leakage switch mainframe expands a single measurement station, such as the Keysight B1500A, 4155C, or 4156C, to an automated measurement system. Plug-in modules can be configured either as a cross-point matrix for general parametric measurements or as a multiplexer for long-term reliability measurements.
-
Product
PXI 8-Slot BRIC Matrix, 88x8 1-Pole (4 Sub-cards)
40-562B-121-88X8
Matrix Switch Module
The 40-562B-121-88X8 is a high density BRIC8 matrix module with a size of 88x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 2 Amp Multiplexer, Quad 8-Channel, 2-Pole
40-635A-009
Multiplexer Module
The 40-635A-009 is a quad 8-channel, 2-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI 4x3 10GHz Matrix with Loop-Thru
40-787-518-4X3-L
Matrix Switch Module
The 40-787 Microwave BRIC platform is designed to provide a solution for complex RF matrix applications. Using a common mechanical platform the module can be constructed to provide scalable non-blocking or blocking microwave matrix for frequencies to at least 20GHz. The standard configurations provide up to a 4x4 matrix. More complex matrix can be constructed by adding further switching functions and other devices inside the module.
-
Product
Regular Flex I/O For Remote Switch
98R17500401
Expansion Module
Flex I/O expansion on the front panel for same-side cablingCompatible with MIC-7500, MIC-7700, MIC-770, MIC-7900
-
Product
Coaxial Plug-in Switch Card
1260-152/172
Switch Card
The Astronics 1260-152/172 is a high- frequency coaxial switch card for use in either the Adapt-a-Switch® 1260-100, VXI carrier, or the 1256, GPIB/RS-232 Switching Mainframe.
-
Product
3-Ch 200 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-7 FPGA - XMC
Model 71721
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Three 200 MHz 16-bit A/Ds- Three multiband DDCs (digital downconverters)- Two 800 MHz 16-bit D/As- One DUC (digital upconverter)- Multiboard programmable beamformer- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
PXI Single 55x8 Matrix 1-Pole Switching
40-538-021
Matrix Switch Module
The 40-538 ultra high density matrix module is configured as a Single 55x8 reed relay matrix with 1-pole switching. Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability Sputtered Ruthenium Reed Relays, offering >10e8 operations to give maximum switching confidence with long life and stable contact resistance.
-
Product
PXI 4-Slot BRIC Matrix, 92x8, 1-Pole (2 sub-cards) Dual Bus
40-560B-021-92X8-M
Matrix Switch Module
The 40-560B-021-92x8-M is an ultra high density matrix module with dual analog buses and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 2-Slot BRIC Matrix, 2A 1-Pole 116x6, 2 Sub-cards
40-596A-202
Matrix Switch Module
The 40-596A-202 is a PXI 1-pole 116x6 matrix in BRIC2 format and is part of a range of high density matrix modules able to switch up to 2 A or 300VDC/250VAC. The 40-596A BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
5G Switch LNA Modules
-
Macom Technology Solutions Holdings Inc.
MACOM offers a complete portfolio of high-power switch and LNA modules to cover many sizes and classes of 5G base stations, including Macro Cell, Small Cell, and massive-MIMO AAS in frequency bands up to 6GHz. SOI-based switch modules with up to 20W LTE power handling are extensively used in mMIMO and Small Cell radios, and MACOM proprietary PIN diode Switch modules with up to 160W LTE power handling are widely deployed in Macro radios. Featuring ultra-broadband, low noise figure and excellent power handling and reliability, the family of Switch LNA modules are also well suited for a variety of TDD based communication systems in commercial and military applications.
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 6-Bank 18GHz SMA
60-801-206
Microwave Multiplexer
The 60-801-206 is a 6-channel, 6-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
Digital Interface Boards
Model 4863 OEM
-
* 114514 Board has same digital capability as the 4863 described above with GPIB IO.* GPIB interface header includes GPIB address switch input signals.* Use with any IC GPIB Connector/Address Switch Assembly.* Uses 9-32 Vdc power.* 114515 Board has same digital capability as the 4863 described above with GPIB and Serial IO.* GPIB interface header includes GPIB address switch input signals.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* Use with any IC GPIB Connector/Address Switch Assembly or with a 114597 Serial Connector Kit.* Uses 9-32 Vdc power.
-
Product
USB, Communications, Avionics And Optical Switching
-
From USB and Optical Switching to ARINC Switching
-
Product
Intelligent Pressure Display Controller
HR5310/HR5311
-
HighReach Measuring & Controlling System Co.,Ltd
HR5310 intelligent pressure display controller is an intelligent pressure measurement and control product that integrates pressure measurement, display, output and control, with RS485 digital interface; the product is a fully electronic structure, using international brand pressure sensors, high-precision A/D conversion, microprocessor operation processing, on-site display, and output of one analog quantity and five switch quantities.The intelligent digital pressure controller is flexible to use, simple to operate, easy to debug, safe and reliable, and is widely used in hydropower, tap water, petroleum, chemical, machinery, hydraulic and other industries to measure, display and control the pressure of fluid media.
-
Product
Switch Probe F88617B300G120LM
1004740
-
The F88617B300G120LM Switch Probe is an innovative device designed for precision and durability in various applications. It features a normally open (NO) configuration that allows for reliable operation in automated systems. This basic contact probe falls under the F886-NO family, capable of withstanding extreme temperatures ranging from -45°C to +100°C, making it ideal for both industrial and laboratory environments. The probe's compact design and high sensitivity ensure it operates effectively even in tight spaces, offering a minimal switch travel of just 1.70 mm and minimal contact resistance of 50 mOhm, which enhances performance and longevity.
-
Product
EBIRST 50-pin D-type To 9-pin D-type Adapter
93-005-238
Test Adapter
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
LXI High Voltage Switching - 1-Bank, 1-Pole, 48:1 Multiplexer Plugin Module
65-231-700-HI
Multiplexer Module
The 65-231-700-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 7 kV. Multiplexers are created by populating the 65-200-002 scalable chassis with multiplexer plug-in modules that provide access to the Channel and Common signals on 51-pin front panel connectors.
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 7-Bank 18GHz SMA
60-801-207
Multiplexer Module
The 60-801-207 is a 6-channel, 7-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
Vibration And Packaging Equipment
-
LR Environmental Equipment Co. Inc.
LR/RAD Drop Testers are available to simulate the impact a package would encounter during handling and shipment. The machine is air actuated to provide a reliable long life. Drop height ranges from 12-60 inches.The Drop Tester is supplied with a variety of standard features to earn its reputation as the industry standard: motor hoist with hand held control box to automatically raise and lower drop arm with package in place, Microswitch to preset drop height for repeatable drops, drop height indicator, remote hand switch actuated and a one inch vertical drop prior to drop arm swing to insure that package is not subject to rotation. LR/RAD Drop Testers are designed so packages may be released from any angle and be assured of landing in the same position. Special fixtures are available to allow for corner and edge drops.
-
Product
AC Insulation Testing
-
Weshine Electric Manufacturing Co., Ltd
High-voltage Dividers (High Potential Divider) are used to measure voltages and decouple partial discharges in high-voltage test systems. Depending on the specific type, they are used to measure alternating voltage (AC), direct voltage (DC), lightning impulse voltage (LI), and switching impulse voltage (SI) systems. High-voltage dividers by HIGHVOLT comply with the relevant IEC standards. The systems are available for both indoor and outdoor use.
-
Product
LXI High-density 896x4, 2A Matrix
60-553-007
Matrix Switch Module
These high-density single pole LXI matrix modules are capable of switching up to 150VDC/100VAC, or 2A (60W max). The use of high-quality electro-mechanical relays offer high switching confidence and make it suitable for signal routing in large ATE systems.
-
Product
PXI 8-Slot BRIC Matrix, 2A 2-Pole 330x4, 6 Sub-cards
40-566B-106
Matrix Switch Module
The 40-566B-106 is a 330x4 matrix with 2-pole switching and is part of a range of high-density large PXI matrix modules with the ability to switch up to 2 Amps or 300VDC/150VAC. They are available in 4 or 8-slot PXI sizes and are constructed using quality electro-mechanical relays for high switching confidence.





























