Coarse Wavelength Division Multiplexing
-
Product
PXI 2A Multiplexer, 1-Bank, 16-Channel, 8-Pole
40-614B-018
Multiplexer Module
This 1-bank, 16-channel, 8-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI Dual 6 to 1 RF Multiplexer 6GHz 50 Ohm SMA Terminated
40-881-002
Multiplexer Module
The 40-881 is a 50 Ohm 6 to 1 6GHz multiplexer available as a single or dual MUX in one and two PXI slots respectively. The 40-881 exhibits low VSWR characteristic over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensure a long service life with no wear out mechanism, making the 40-881 ideal for ATE systems requiring frequent and fast operating RF switching with no contact bounce.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 2-Bank 40GHz SMA-2.9
60-802-402
Multiplexer Module
The 60-802-402 is a 4-channel, 2-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PXI 2 Amp MUX, Single 64-Channel 1-Pole
40-635-001
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI MUX 1 Bank, 64 Channel Screened 1 Pole
40-610-021-S-1/64/1
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
PXI/PXIe MEMS Optical MUX, Single 2-Channel, Multi-Mode, 62.5/125 Fiber
40-855A-212-M-HI
Multiplexer Module
The 40/42-855A-212-M-HI is a PXI/PXIe 2-channel multiplexer with SC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP4T, 50 GHz, 50 Ω, SMA-2.4, Terminated, Remote Mount, Failsafe
42-785C-453-TE
Multiplexer Module
The 40-785C-453-TE (PXI) and 42-785C-453-TE (PXIe) are triple failsafe SP4T 50 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
PXI 8-slot BRIC Power Multiplexer, 12-Channel, 24-Pole (8 Sub-cards)
40-571A-106
Multiplexer Module
The 40-571A-106 is a 12-channel, 24-pole 3 Amp Power Multiplexer and is part of our BRIC family. The 40-571A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
Product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass, Single-Mode
40-860A-022-HI
Multiplexer Module
The 40/42-860A-022-HI is a PXI/PXIe dual insert/bypass switch with FC/APC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
PXI/PXIe RF Multiplexer, Dual 4-Channel, 3GHz, 75Ω, MCX
40-832A-102
Multiplexer Module
The 40-832A-102 (PXI) and 42-832A-102 (PXIe) are 75 Ohm 4 to 1 RF multiplexers with 2 banks in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
LXI 8:1 Optical MUX SC Multi Mode
60-851-211
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP12T, 18 GHz, 50 Ω, SMA, Remote Mount, Failsafe
40-788-221-E
Multiplexer Module
The 40-788-221-E (PXI) and 42-788-221-E (PXIe) are single failsafe SP12T 18 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
Product
PXI/PXIe MEMS Optical MUX, Single 2-Channel, Single-Mode, 9/125 Fiber, LC Connectors
40-855A-412
Multiplexer Module
The 40/42-855A-412 is a PXI/PXIe 2-channel multiplexer with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
PXI/PXIe RF Multiplexer, Single 4-Channel, Terminated, 3GHz, 50Ω, MCX
40-873A-101
Multiplexer Module
The 40-873A-101 (PXI) and 42-873A-101 (PXIe) are 4 to 1 RF MUX with 1 bank in a single slot. Additionally, extra switching allows unused channels to be terminated into 50 Ohm, maintaining signal integrity. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz.
-
Product
PXI Very High Density Multiplexer, 24-Channel, 8-Pole
40-675A-002-24/8
Multiplexer Module
The 40-675A-002-24/8 is a 24-channel, 8-pole MUX and is part of our range of PXI very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
Product
PXI-2530B, 128-Channel, 1-, 2-, or 4-Wire PXI Multiplexer Switch Module
778572-30
Multiplexer Module
128-Channel, 1-, 2-, or 4-Wire PXI Multiplexer Switch Module—The PXI‑2530B is a high-density, multiconfiguration reed-relay switch. With four multiplexer and three matrix configurations, the PXI‑2530B is an excellent solution for complex or high‑channel‑count systems. Multiplexer configurations include 128x1 (1‑wire), 64x1 (2‑wire), 32x1 (4‑wire), or eight banks of 16x1 (1‑wire). Matrix configurations include 4x32 (1‑wire), 8x16 (1‑wire), or 4x16 (2‑wire). You can implement these configurations by selecting the appropriate terminal block.
-
Product
PXI/PXIe Very High Density Multiplexer, 198-Channel, 1-Pole
42-675B-002-198/1
Multiplexer Module
The 40-675B-002-198/1 (PXI) and the 42-675B-002-198/1 (PXIe) are 198-channel, 1-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 67GHz, 50Ω, SMA-1.85
40-785C-572-E
Multiplexer Module
The 40-785C-572-E (PXI) and 42-785C-572-E (PXIe) are dual SP6T 67GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 5-Bank 18GHz SMA
60-801-205
Multiplexer Module
The 60-801-205 is a 6-channel, 5-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 50/125 Fiber, FC/PC Connectors
42-852A-118-M50
Multiplexer Module
The 40/42-852A-118-M50 is a PXI/PXIe 8-channel multiplexer with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
PXI/PXIe MIL-STD-1553 Multiplexer, Dual 4-Channel, 2-Pole
42-739-006
Multiplexer Module
The 40-739-006 (PXI) and 42-739-006 (PXIe) are dual 4-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
Product
LXI Microwave Multiplexer, SP6T, 7-Bank, 18GHz, 50Ω, SMA
60-800-107
Microwave Multiplexer
Our 60-800-107 is a 7 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
LXI Microwave Multiplexer, SP6T, 10-Bank, 50GHz, 50Ω, SMA-2.4
60-800-610
Multiplexer Module
Our 60-800-610 is a 10 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXI 5A Power Multiplexer, 2-Bank, 24-Channel, Independent Isolation
40-651A-102
Multiplexer Module
The 40-651A-102 is part of our range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC.
-
Product
PXI Very High Density MUX 24 Chan 8 Pole
40-675-002-24/8
Multiplexer Module
The 40-675 series of very high density low cost multiplexer modules are available in a versatile range of switching configurations. The modules are supplied pre-configured in one of six multiplexer modes suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
Product
PXI Single SP6T Multiplexer 26.5GHz 50 SMA
40-784A-031
Multiplexer Module
Pickering Interfaces’ range of 40-784A PXI Microwave Multiplexer Modules have a characteristic impedance of 50Ω and are capable of switching signals up to 40GHz. Available in single, dual or triple, SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors
-
Product
PXI High Density MUX BRIC, 40-Chan, 20-Pole
40-570-315
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
PXI/PXIe High Density 2A Multiplexer, 4-Bank, 16-Channel, 2-Pole
42-614D-007
Multiplexer Module
The 40-614D-007 (PXI) and 42-614D-007 (PXIe) 4-bank, 16-channel, 2-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI MUX 1 Bank of 64 Channel 1 Pole
40-610-021-1/64/1
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP4T, 50GHz, 50Ω, SMA-2.4
40-785C-452-T
Multiplexer Module
The 40-785C-452-T (PXI) and 42-785C-452-T (PXIe) are dual SP4T 50GHz microwave multiplexers with automatic termination of unused signals. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
