Coarse Wavelength Division Multiplexing
-
product
PXI 2 Amp Multiplexer, Single 4-Channel, 8-Pole
40-635A-104
The 40-635A-104 is a single 4-channel, 8-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
PXI Dual 4 to 1 Terminated RF Multiplexer 3GHz 50 Ohm MCX
40-873-102
The 40-873-102 is a 4 to 1 RF MUX with 2 banks in a single PXI slot. Additionally, extra switching allows unused channels to be terminated into 50 Ohm, maintaining signal integrity. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz.
-
product
PXIe Microwave Multiplexer, Dual SP6T, 26.5 GHz, 50 Ω, SMA, Failsafe
42-785C-532
The 40-785C-532 (PXI) and 42-785C-532 (PXIe) are dual failsafe SP6T 26.5 GHz unterminated microwave multiplexers. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
product
LXI Microwave Multiplexer, SP4T, 9-Bank, 18GHz, 50Ω, SMA
60-803-109
Our 60-803-109 is a 9 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
PXI 10A Power MUX 8-Bank 4-Channel
40-661-001
The 40-661 is a single pole PXI power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available. Signal connections are made via front panel mounted 20-way GMCT plugs.
-
product
LXI Microwave Multiplexer, 50Ω 4-Channel 1-Bank 40GHz SMA-2.9
60-802-401
The 60-802-401 is a 4-channel, 1-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
PXI High Density Multiplexer, 4-Bank, 16-Channel, 1-Pole, Screened
40-610A-014
The 40-610A-014 is a screened 4-bank, 16-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. The range includes a wide choice of switching configurations which are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems.
-
product
PXI 5 x 4 to 1 RF Multiplexer 500MHz 50 Ohm Multiway Connector
40-755-005
The 40-755-005 is a 50 Ohm high-density RF multiplexer (4 to 1) array available with 5 MUXs in a single PXI module. The 40-755 range is available with two connector options, an SMB connector that provides a frequency range of 1.8GHz and is available in single or dual PXI slots, or a multiway connector which limits the bandwidth to 1.3GHz but offers a high density solution occupying just one PXI slot. The RF switch design is identical in each case.
-
product
PXI High Density MUX 94-Channel 1-Pole
40-640-022-94/1
This series of high density multiplexer modules feature a choice of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The multiplexer module is available as a 47-channel 2-pole, 94-channel 1-pole or 47-channel 1-pole with screened relays. Connections are made via a front panel 96-pin connector. It may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available for this 1-pole version).
-
product
LXI Microwave Multiplexer, 50Ω 4-Channel 6-Bank 18GHz SMA
60-802-206
The 60-802-206 is a 4-channel, 6-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
Single 48-Channel 1-Pole 5 Amp PXI Solid State Multiplexer
40-652-001
The 40-652 range of multiplexers uses solid state relays with high tolerance to surge currents and hot switching events. Each multiplexer provides an isolation relay in the common to minimize capacitive loading when expanding the multiplexer across multiple modules. The 40-652 can sustain 30A for 300s on hot or cold switching. User connections are made via a 50-way D-Type connector which is fully support by our comprehensive range of cables and connector accessories.
-
product
PXI/PXIe MEMS Optical MUX, Single 2-Channel, Multi-Mode, 62.5/125 Fiber, ST Connectors
40-855A-512-M
The 40/42-855A-512-M is a PXI/PXIe 2-channel multiplexer with ST connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
PXI Microwave Multiplexer, Single SP4T, 26.5GHz, 50Ω, SMA, Terminated
40-785C-431-T
The 40-785C-431-T (PXI) and 42-785C-431-T (PXIe) are single SP4T 26.5GHz microwave multiplexers with automatic termination of unused signals. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
product
PXI/PXIe RF Multiplexer, Dual 4-Channel, Terminated, 3GHz, 50Ω, MCX
42-873A-002
The 40-873A-102 (PXI) and 42-873A-102 (PXIe) are 4 to 1 RF multiplexers with 2 banks in a single slot. Additionally, extra switching allows unused channels to be terminated into 50 Ohm, maintaining signal integrity. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz.
-
product
LXI Microwave Multiplexer, SP4T, 6-Bank, 50GHz, 50Ω, SMA-2.4
60-803-706
Our 60-803-706 is a 6 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
PXI High Density MUX BRIC, 5-Chan, 160-Pole
40-570-015
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
PXI Very High Density Mux 10 Ch 16 Pole
40-670A-022-10/16
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
product
PXI Single SP4T MUX 26.5GHz 50Ω SMA
40-784-131
Pickering Interfaces’ 40-784 PXI Microwave Multiplexer Modules have a characteristic impedance of 50 Ohm and are capable of switching signals up to 40GHz. Available in single or dual SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
PXI 16 Bank 5 Channel 1 Pole Multiplexer
40-616-021-16/5/1
The 40-616 16-Bank, 5-Channel, 1-Pole Multiplexer Module forms part of the System 40 PXI Programmable Switching system. The Module consists of 16 electrically isolated banks of multiplexers controlled by a PXI/ PCI interface. Each bank is a 1 to 5 multiplexer and operates with break-before-make action when a new channel is selected. Any Individual multiplexer bank can have a channel set by itself, alternatively, multiple banks can have channels selected simultaneously. The module is suitable for cascading in applications that require large multiplexer systems, it is also suitable for test systems that require the switching of a large number of signals in parallel.
-
product
PXI/PXIe RF Multiplexer, Dual 4-Channel, Terminated, 8GHz, 50Ω, SMA
42-882B-002
The 40-882B-002 (PXI) and 42-882B-002 (PXIe) are dual 50Ω 4 to 1 RF multiplexers with 8GHz bandwidth.The 40/42-882B range has automatic termination of unused signals and are available as a single MUX in one slot, a dual MUX in two slots, or triple and quad MUXs in three slots.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 62.5/125 Fiber
40-850A-314-M62.5-HI
The 40/42-850A-314-M62.5-HI is a PXI/PXIe 4-channel multiplexer with MU (mini SC) connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
PXI 3A Power MUX BRIC, 10-Channel, 24-Pole
40-571-105
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
LXI Microwave Multiplexer, 50Ω 6-Channel 16-Bank 26.5GHz SMA
60-801-316
The 60-801-316 is a 6-channel, 16-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
LXI Microwave Multiplexer, SP6T, 13-Bank, 67GHz, 50Ω, SMA-1.85
60-800-813
Our 60-800-813 is a 13 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
LXI Microwave Multiplexer, 50Ω 6-Channel 6-Bank 18GHz SMA
60-801-206
The 60-801-206 is a 6-channel, 6-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
PXIe Microwave Multiplexer, Single SP4T, 26.5 GHz, 50 Ω, SMA, Failsafe
42-784B-131
The 40-784B-131 (PXI) and 42-784B-131 (PXIe) are single failsafe SP4T 26.5 GHz unterminated microwave multiplexers. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber, LC Connectors
42-850A-414
The 40/42-850A-414 is a PXI/PXIe 4-channel multiplexer with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
product
PXI MUX 2 Banks of 32 Channel 1 Pole
40-610-021-2/32/1
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
product
LXI Microwave Multiplexer, SP4T, 7-Bank, 50GHz, 50Ω, SMA-2.4
60-803-707
Our 60-803-707 is a 7 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 62.5/125 Fiber, FC/APC Connectors, With Interlock
42-850A-014-M62.5-HI
The 40/42-850A-014-M62.5-HI is a PXI/PXIe 4-channel multiplexer with FC/APC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
