Voltage Standards
-
Product
High Voltage Snubber Capacitor
STP-01RAN/STP-01RFN/STP-01RFB
-
This series of capacitors is Plastic Enclosure, Dry construction design and doesn't have leakage problem when compared with traditional Metal Enclosure Oil impregnated capacitors.Handle Medium Frequency range, high surge current, RMS current and surge voltage with temperature up to +105CCapacitance : 0.1uF - 15uF ( can be customized )Voltage range : 1,200Vdc to 17,000Vdc / 350Vrms to 6,900VrmsRMS Current - Irms : up to 100Armspeak to peak pulse current - Ipp : up to 5,900AppTemperature ranges : +85C / +105C
-
Product
Dielectric Withstanding Voltage Test
-
The dielectric withstanding voltage test (also called high-potential, over-potential voltage-breakdown, or dielectric-strength test) consists of the application of a voltage significantly higher than rated voltage for a specific time, between mutually insulated portions of a component part or between insulated portions and ground. This is used to prove that the component part can operate safely at its rated voltage and withstand momentary over-potentials due to switching, surges, and other similar phenomena.
-
Product
Ultra Low Level DC Voltage Amplifiers
-
The EM A10 is a low level amplifier module for sensitive measurements, data collection and systems, where signals below 1 nanovolt may be measured. It is ideal for the input unit for precision voltage measuring systems, requiring voltage sensitivity for measuring low noise and low impedance sources. The noise level of the A10 is equivalent to a perfect resistor of about 20 ohms. When used with a digital voltmeter, steady one nanovolt digits may be displayed, with a response time constant of less than a second. The input voltage stability of the A10 is very high, with the drift around a nanovolt per degree C. The input connectors are made from pure copper. The input impedance is very high, and is time dependent, determined by the loop gain.
-
Product
AC DC Current and Voltage Converters
-
The DAT5023 I is an AC or DC current converter, the input current range is selectable on order from 0-5Amps, 0-10Amps, 0-20Amps, 0-25Amps, 0-30Amps, 0-40Amps, 0-50Amps, 0-60Amps. It measure the current with the use of a Hall effect transducer. There is a coil (current transformer) inside the current converter which is isolated from the current input. The cable passes through the housing of the converter and the coil and the true root mean square measurement is taken from this coil then converted to a standard industrial signal output.
-
Product
Standard 1.10 (31.00) - 3.85 (109.00)General Purpose Probe
SPA-64-2
-
Current Rating (Amps): 3Average Probe Resistance (mOhm): 50Test Center (mil): 100Test Center (mm): 2.54Test Center Remark: max. test center 187 mil / 4,74 mmFull Travel (mil): 50Full Travel (mm): 1.27Recommended Travel (mil): 50Recommended Travel (mm): 1.27Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 375Overall Length (mm): 9.53Overall Length Remark: Exact length depends on selected tip: Tip 1,4, 7: 0,375″; Tip 2,3: 0,365″; Tip 8: 0,385″; Tip ,9,10: 0,363″
-
Product
HIPOTS (High Voltage Testers) / AC Hipots
5 kV Digital
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Panel mounted controls & indicators. Variable from zero to 5 kV. Digital kV and leakage mA meter.
-
Product
T3 Low & High Voltage Differential Probes
T3 Series
-
Teledyne Test Tools Low & High Voltage Differential Probes offer end user versatility with all models powered by an external universal power supply and work with any Oscilloscope with a high-impedance BNC input. The range consists of one Low Voltage and three High Voltage models with varying bandwidths to satisfy a wide array of customer applications.
-
Product
PXI/PXIe High Voltage Multiplexer, Single 23-Channel, 2-Pole
42-321-127-HI
-
The 40-321-127-HI (PXI) and 42-321-127-HI (PXIe) are single 23-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-353-HI
-
The 40-230-353-HI (PXI) and 42-230-353-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 11.32MΩ with 1Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-022-HI
-
The 40-230-022-HI (PXI) and 42-230-022-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 3Ω and 1.81kΩ with 0.5Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
LXI High Voltage Switching - 40xSPST Plugin Module
65-233-901
-
The 65-233-901 plug-in module is part of a scalable high voltage switch platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
Relay Testing Voltage Source
PTE-FCL
-
It is the easiest and most economical way of increasing the relay types that can be tested with the PTE-100-C. The PTE-FCL upgrades the PTE-100-C to the PTE-100-C Plus model.
-
Product
High Voltage AC Test Systems
-
Our range of high voltage AC test systems cover from 5kVac to 100kVac. All units have a variable trip range setting and key lock operation to prevent unauthorised use. Applications include testing of insulation systems and measurement of break down voltage of electrical plant and components.
-
Product
High Voltage, High Current Linear Amplifier
P200
-
The P200 is a general purpose linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±100V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device.
-
Product
High voltage amplifiers (to ±500V)
-
These amplifiers provide high amplitudes and bandwidths, and are well suited for use as booster amplifiers for lower-voltage arbitrary waveform generators.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-220-HI
-
The 40-230-220-HI (PXI) and 42-230-220-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 3Ω and 472Ω with 0.125Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-225-HI
-
The 40-230-225-HI (PXI) and 42-230-225-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 3Ω and 13.6kΩ with 4Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
2kV, 400 MHz High Voltage Differential Probe
HVD3220
-
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
Product
Standard 0.62 (18.00) - 4.00 (114.00) High Performance Bias Ball Probe
POGO-1T1-4
-
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Two-pole Voltage Testers
-
PeakTech Prüf- und Messtechnik GmbH
Two-pole voltage testers are ideal for quick and uncomplicated voltage measurements.
-
Product
Standard Mechanical Calibration Kit, DC To 7.5 GHz, 7–16 (male)
85038M
-
Modern wireless communication systems require high-performance components offering low VSWR and low intermodulation distortion at high transmit power levels. To meet these needs, 7-16 connectors are becoming increasingly common in base station transmitters, amplifiers, duplexers, and other products. These connectors conform to IEC 169-4, DIN 47223, European standard EN 122190, and British standard BSEN 122190.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-342-HI
-
The 40-230-342-HI (PXI) and 42-230-342-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 392kΩ with 0.5Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Impulse Voltage Generator
SKS-255I
-
Shanghai Sanki Electronic Industries Co., Ltd.
The impulse voltage generator SKS-255I is manufactured in accordance with the IEC60255-5 "Insulation Test of Electrical Relays" promulgated by the International Electrotechnical Commission. It measures the insulation coordination between relays and protection devices and performs impulse voltage tests.
-
Product
Voltage Detectors
JSC
-
The JSC family of devices provides a highly reliable way to determine if voltage is present downstream of the disconnector or circuit breaker knives during zero-energy shutdowns. They dramatically increase the safety of personnel performing maintenance on electrical equipment. When voltage is present downstream of the disconnector knives, one or more LEDs on the JSC-88A will remain illuminated. The JSC's compact design allows for direct installation on the disconnector door, starter, or control panel.
-
Product
High Voltage Pulse
-
For thicker coatings such as coal tars, extruded and tape coatings, It has a range of infinite voltage settings from 1,000 to 15,000 volts. This wide range permits you to maintain a steady inspection rate on most types of coatings on most pipe sizes without changing detectors. Pulse voltage output only.
-
Product
Standard 0.62 (18.00) - 4.00 (114.00) High Performance Bias Ball Probe
POGO-1T30-4
-
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
High Voltage Oil Test Set
-
Supreme Instrument Laboratories
Supreme High voltage Oil Testing Apparatus is designed for testing of dielectric strength of transformer Oil or any other insulating liquids. It constitutes a complete equipment and apart of an A.C. supply of 230 / 240 Volts, no other supplementary facilities are required for its operation.
-
Product
Standard 1.60 (45.00) - 4.50 (128.00) General Purpose Probe
EPA-3A
-
Current Rating (Amps): 6Average Probe Resistance (mOhm): 35Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Standard 1.10 (31.00) - 3.85 (109.00)General Purpose Probe
SPA-64-1
-
Current Rating (Amps): 3Average Probe Resistance (mOhm): 50Test Center (mil): 100Test Center (mm): 2.54Test Center Remark: max. test center 187 mil / 4,74 mmFull Travel (mil): 50Full Travel (mm): 1.27Recommended Travel (mil): 50Recommended Travel (mm): 1.27Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 375Overall Length (mm): 9.53Overall Length Remark: Exact length depends on selected tip: Tip 1,4, 7: 0,375″; Tip 2,3: 0,365″; Tip 8: 0,385″; Tip ,9,10: 0,363″
-
Product
Low Noise Voltage Preamplifier
1201
-
The Model 1201 Voltage Preamplifier with Remote Gain Programming Option (06) is usable in both computer controlled and maual applications requiring uncompromising performance.
