Wrist Strap & Footwear Testers
-
Product
Solar Cell Testers
-
Solar Cell Testers are integrated systems incorporating Solar Simulator and I-V Measurement systems. PET offers Standard and Advance IV Measurement software. PET Cell Testers are capable of measuring a diverse range of solar cell parameters such as Isc,Voc, Imax,Vmax, Pmax, FF, Rsh, Rs and η cell conversion efficiency, complete light and dark I-V curves. All that needs to be done to test a cell is to load the cell, make electrical probes contact and press “Measure” icon on the I-V Measurement System software. The software will automatically open the Solar Simulator shutter, perform the test and close the shutter after the test is complete. The design is modular in nature and can be easily upgraded. Some options can added at a later time.
-
Product
Velcro Tester
TF151
-
TESTEX Testing Equipment Systems Ltd.
Velcro Tester, to determine the capability of Velcro used for shoes, garments, etc.Cut the specimen 540mm by 20 or 50mm in dimension from the sample being tested into the wheel of Velcro tester to be fitted completely. To subject Velcro (hook & loop) to repeated stripping and peeling for a certain number of times. Use tensile machine (another purchase) to measure its peeling strength (AS) and shear strength (PA) after this test.
-
Product
Wi-Fi / Bluetooth / GPS Tester
MP5010
-
*Wi-Fi/Bluetooth/GPS Mobile Phone Tablet Integration Tester
-
Product
RCD Testers
-
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2710 is a residual current tester, which is used to determine tripping currents and the tripping times of residual current circuit breakers, which are used in every new building according to current building regulations. Residual current circuit breakers are used for personal protection and switch off a circuit when a residual current is registered which flows off via the protective earth (PE). RCD testers let a fault current flow and thus determine at which fault current the RCD triggers. The tripping time is also measured. These two parameters, tripping current and tripping time, are the safety-relevant parameters of an RCD. The various selectable test currents and characteristics that can be set with this device make the PeakTech 2710 the ideal companion for every electrician.
-
Product
Oil Breakdown Voltage Tester
DTA 100 C
-
Insulating oil testing with the BAUR DTA 100 C. The BAUR DTA 100 C oil tester is designed for continuous operation in the laboratory and is characterised by the combination of extraordinary features. As a high-performance device with a test voltage up to 100 kV, with clear breakdown detection and absolutely reliable measurement results even across several measurement sequences, the BAUR DTA 100 C is the leading testing device for users in the electricity and other industries and in testing institutes.
-
Product
Analog In-Circuit Tester
406C
-
The 406C is an open architecture power up test platform designed to facilitate the implementation of functional testing after the MDA test is completed. Internally dubbed as "Armadillo" the new architecture provides the user almost unlimited flexibility by combining the best of the VME buss and a dedicated ICT buss.
-
Product
Resistive Current Tester
-
Weshine Electric Manufacturing Co., Ltd
Long Distance Digital Zinc Oxide Arrester Resistive Current Safety Testing Set
-
Product
Shoe Cold Insulation Tester
UI-FT09
-
Shoe Cold Insulation Tester is used to test shoe cold insulation ability / thermal insulation against cold performance..
-
Product
Oil Breakdown Voltage Tester
DPA 75 C
-
Insulating oil testing with the BAUR DPA 75C. The BAUR DPA 75C oil tester developed especially for mobile use in the field is one of its kind in the market due to its functionality and excellent user benefits in comparison to the costs. The BAUR DPA 75C delivers clear and reliable measurement results.
-
Product
Digital Earth Resistance Tester
8PK-ST1520
-
Capable of measuring earth voltage (Vac.) 2mA measuring current permits earth resistance to test without tripping earth leakage current breakers in the circuit. Battery operated. Auto power off function. Data hold function. Small and light weight.
-
Product
Thickness Tester
CX-Series
-
The Thickness Tester - CX-1000 combines our patented capacitance sensor with industry-leading software to give you plastic film thickness profiling resolution to one micron. This gauge can be run as a stand-alone bench unit, or can be connected to a computer for RS-232 operation by our Thickness Tester - CX-1100 Quality Control Software. Capacitance measurement is industry-recognized as the best choice for off-line, high resolution, continuous gauge profiling for plastic films.
-
Product
Keyboard Button Testers
-
Infinity Machine International Inc.
Keyboard Button Testers by Infinity Machine International Inc. - for applications such as keyboard button compression force tester, keyboard durability test machine, adjustable keystroke life-span tester, mechanical keyboard switch tester, computer keystroke tester, button force testing, key stroke force tester for load stroke curve test, rubber keystroke tester, and more.
-
Product
Multifunction Tester
M70
-
M70 is a mobile device dedicated to measuring Insulation resistance with test voltage up to 1000VDC and Continuity of protective and equipotential conductors with current of 200mA in private and industrial electric installations.
-
-
Product
Color Tester
OCM-510 series
-
The OCM-510 Color Tester has an internal Czerny-Turner spectro- scope and along with providing both high-wavelength precision and high-wavelength resolution in a compact unit also employs a high-precision yet high-sensitivity line sensor in the detector to serve as a versatile spectrophotometric device for making optimal high-speed measurements.
-
-
Product
6-Phase Protection Relay Tester
HME-1200
-
HAOMAI Electric Power Automation Co., LTD.
Economical 6-phase Protection Relay Tester 6-phase current (6×30A) + 6-phase voltage (6×120V) output.
-
Product
Modbus Simulator & Tester
Modbus Poll
-
Modbus Poll is a Modbus master simulator designed primarily to help developers of Modbus slave devices or others that want to test and simulate the Modbus protocol. With the multiple document interface you can monitor several Modbus slaves and/or data areas at the same time. For each window you simply specify the Modbus slave ID, function, address, size and poll rate.
-
Product
Ink Rub Tester
RT-01
-
Ink Rub tester, also known as abrasion resistance tester, using ASTM D5264 and is designed to measure the ink resistance against rubbing on packaging materials. RT-01 Ink Rub Tester is designed for the abrasion resistance of surface coating layers of printed materials, such as ink layer or photosensitive coating.
-
Product
Insulation and Continuity Tester
MIT2500
-
The MIT2500 insulation and continuity tester has been designed for motor and cable testing, specialist applications and electrical testing applications, where operation voltages exceed 1000 V and higher insulation test voltages are needed. The MIT2500 offers both fixed range voltages of 50 V, 100V, 250 V, 500 V, 1000 V and 2500 V, as well as a variable range that allows any voltage between 50 V and 2500 V to be "dialled in". This is supported by the new test voltage feedback control, which maintains the output test voltage to within 2% of the selected range, even when under test.
-
Product
Single-Functional Testers
-
Electrical installation safety testing is a wide subfield of general electrical safety testing and encompasses both troubleshooting and fault-finding in complex industrial installations and simple, often periodic testing of only specific parts of the installation. The former usually requires the use of multifunctional testing devices, while the latter can be more conveniently done by testers with far fewer test and measurement functions.
-
Product
Digital ELCB Testers
6221 EL-M
-
Standard Electric Works Co., Ltd
● High contrast OLED display.● Designed for viewing in the dark, for mining industry.● Microprocessor-controlled.● Indicates phase rotation● Indicates phase presence● TEST for disconnection sensitivity● Battery status indicator● Measures Voltage Phase to Earth● Select one of 3 Phase to test ELCB.● Color-coded test leads.● Phase presence indication from as low as 100Vac.● Fused earth leakage tester.● ELCB works 50Vac to 330Vac 50Hz / 60Hz.● Phase rotation and presence does not require battery to indicate.
-
Product
Leakage Current Tester
-
Test Voltage : - 1V to 500V DC settableAccuracy : ± 1% of set Value ± 1digitLeakage Current : - Accuracy - ± 0.5% ± 1digitDigital Model – 19.99μA / 199.9 μA / 1.999mA / 19.99mAAnalog Model - 10μA /25μA/100 μA/1mA/2.5mA/10mASeparate Indication for Charge / Measure and Discharge modeAvailable in Digital Version Also
-
Product
Digital In-Circuit tester
MTS180/300
-
Analog in-circuit inspection and function inspection are realized on this inspection equipment. IC pin float function is standard equipment. The MTS180 is a press type jig, and the MTS300 is a vacuum type jig. In the board mounting process at the production site, electrical inspection is performed on the mounted board after component mounting, and non-defective or defective products are automatically judged. The main inspection contents are short / open inspection, analog inspection of resistors, capacitors, coils, diodes, etc., lead floating voltage measurement of QFP and BGA, Digital IC inspection, frequency measurement.
-
Product
Electroscope Tester
-
Weshine Electric Manufacturing Co., Ltd
1. The high voltage is extremely spherical and the grounding voltage is annular.2. The grounding electrode is fixed and the high voltage electrode can be electrically driven to move to the left and right.3. The motor is controlled by two ways: button and wireless remote control. At the same time, there is fine tuning control, which is easy to adjust the distance accurately.
-
Product
Electromagnetic Field Tester
-
The EMF tester is designed to provide user a quick, reliable and easy way tomeasure electromagnetic field radiation levels around power lines, home appliancesand industrial devices.
-
Product
Surge/Impulse Testers
-
specifically designed to perform the Input Test on PV Panels in accordance with IEC 61730-2, Para. 10.5.3. The output is in accordance with the published waveform from 800-10000V peak (open circuit).
-
Product
Roughness Testers
-
Roughness is an important parameter when trying to find out whether a surface is suitable for a certain purpose. Rough surfaces often wear out more quickly than smoother surfaces. Rougher surfaces are normally more vulnerable to corrosion and cracks, but they can also aid in adhesion. A roughness tester is used to quickly and accurately determine the surface texture or surface roughness of a material. A roughness tester shows the measured roughness depth (Rz) as well as the mean roughness value (Ra) in micrometers or microns (µm). Measuring the roughness of a surface involves applying a roughness filter. Different international standards and surface texture or surface finish specifications recommend the use of different roughness filters. For example, a Gaussian filter often is recommended in ISO standards.
-
Product
Compact Tablet Hardness Tester
HC 7
-
The new member of our Lab.line product family: the HC 7 hardness tester for manual use in the laboratory.Equipped with a touch display and the new database-driven touch software, the HC 7 impresses with its exceptional user-friendliness. The new software can be operated intuitively and is equipped with all important functions for quick operation.Start your quick, direct and product testing with just a few clicks directly via the touch display and set up to 50 products. Reports can be printed externally via USB or LAN interface. It is also possible to connect DYMO* and EPSON* roll printers (*special models only).
-
Product
Wire Harness Tester
NX Solo
-
The Dynalab NX Solo Tester is an economical, feature-rich, stand-alone wire harness tester offering up to 256 test points. The powerful NX Editor software application is used to create unique program files to successfully validate all electrical and electro-mechanical wire harness parameters. This tester is compatible with all Dynalab NX accessories such as printers, scanners, control ports, and much more. The NX Solo Tester supports network communications with the NX Server for efficient file transfers and advanced data collection.
