Wrist Strap & Footwear Testers
-
Product
Earth Resistance Testers
-
Precision Mastech Enterprises Co.
Specialized instruments used to measure the effectiveness of grounding systems in electrical installations.
-
Product
Vehicle Actuator Tester
7651
-
Peaceful Thriving Enterprise Co Ltd
This device is design to test electronic components actuate by magnetic field or electronic magnetic field. Devices like actuator, ignition coil, AC generator, indoor air blower, valve controller EGR (exhaust gas control), injector, spark plug, relay and hall effect sensor can be tested.
-
Product
CW Repeater Tester
MS 1108
-
The CW Repeater Tester is a computer-controlled system used to test CW Unit Electronics and its modules.
-
Product
DC Resistance Tester
DCSS502BC
-
Resistance meter is designed to measure copper resistance of transformers, wires, cables, other conductors and other coil products etc. It is widely used of low resistance measurement of switches, heater wires, transformers, relays, motors, electric films and PC circuit boards, wires, cables, etc. With reliable Good/ NG judgement, it is a premier resistance meter for the use in production line or QC department.
-
Product
Programmable Parametic Tester
IST 878
-
IST Information Scan Technology, Inc.
The IST 878 is a low cost test instrument that provides in-circuit or out-circuit testing for a wide range of discrete semiconductors
-
Product
Electronic Tire Tester
Model BTT-5700
-
The Branick BTT-5700 was created from the ground up to be the most efficient, durable and reliable electronic tire tester available. The electronic detector accurately locates flaws that may be missed using conventional methods. A visible spark occurs at the site of a flaw and the rotation stops to allow the flaw to be marked. The adjustable height platform reduces physical strain that can often lead to workers compensation claims. The BTT-5700 also features a bi-directional variable speed electric rotation motor that is whisper quiet. The auto extend/retract ramp makes tire loading easy. Hand controls are located on a locking swing arm that can be adjusted in seconds. Four air tool ports and two electric outlets are also provided so any needed tools can be kept close for improved efficiency. A high power LED light and Medium Truck Probe are also included. All probe heads require only the push of a button to change and are available to fit all common tire sizes. And, like everything from Branick, it's made in the USA.
-
Product
Reconfigurable Automatic Tester
-
Quick-Start Reconfigurable Automatic TesterCompact, Efficient Desktop Tester with Customer-Configurable PXI/PXIe Insert PXI/PXIe Insert – 8 Slots: 1 Controller, 7 Customer-Configurable PXI/PXIe Slots.
-
Product
Carbon Black Tester
-
Chongqing TOP Oil Purifier Co., LTD
Carbon Black Tester by Chongqing TOP
-
Product
Bare Board Tester
1232
-
High-Precision Batch Fixture-Type Testing System that Support Boards with Embedded Passive and Active Devices. The 1232 is a bare board tester that utilizes the full range of Hioki’s in-circuit testing technologies to deliver LSI reliability testing, complex component separation testing, high continuity and insulation testing, and more. (Double-sided alignment) Testable board dimensions: 50 × 50 to 330 × 330 mm (including clamp area) • Support for build-up boards that require resistance guarantees.
-
Product
Franklin Tester
Model 717
-
The Model 717 Franklin Tester provides a means of testing single strips or punchings of flat rolled electrical steel, for surface insulation resistance under predetermined conditions of voltage and pressure.
-
Product
60204 Safety Testers
-
For testing the electrical safety of machines and devices according to the machinery directive EN60204 and VDE113.
-
Product
Display Tester
-
Yuyao City Yinte Neon-Electroscope Factory
This neon-electroscope is applicable for directly detection of 12-240V zero line indirect detection of DC.
-
Product
Press-type Vibration Tester
9363-PC-ESS
-
King Design Industrial Co., Ltd.
This machine complies with the IEC, JIS and other 5-100Hz low-frequency specifications; applied to test the post-assembly products at end of the production line. Use resonance amplification, the product’s flaws can be screened out in advance. The operation is convenient, fast and effective.Apply Japan-imported motor; durable and safe in operation.Bellow-type damper: use special damping material that can effectively absorb vibration; allowing the test to be performed without affecting floor structure.Motor drive system is embedded in the seat; good in vibration block-out; rigidity is strong. Follow specimen to design fixture.
-
Product
Bally Flexing Tester
TF116
-
TESTEX Testing Equipment Systems Ltd.
Bally flexing Tester is designed for flexing resistance test to be and ingor other types of failure at flexing creases. The machines applicable to all flexible materials,in particular leathers, artificial leather below thickness
-
Product
Flying Probe Tester
FA1817
-
Flying Probe Tester FA1817, an automatic testing system designed to inspect printed wiring on bare boards. The FA1817’s features and capabilities make it ideal for use in inspecting high-density printed wiring boards. With support for a broad range of test types, from low-resistance measurement to high-insulation-resistance measurement, the system reliably detects the latent defects that trouble end-users.
-
Product
AMIDA 2020XP Tester
-
AMIDA 2020XP CIS tester is the latest generation of CMOS image sensor-specific measuring instruments from Metatech. In addition to the original true and accurate measurement, the high-throughput mass production solution designed for the high-throughput inspection of image lens modules and camera lenses has been well received after nearly 20 years of mass production experience. First-class factories at home and abroad import production. AMIDA 2020XP CIS testing machine not only meets the customer's testing time and high output and accuracy requirements. Within the range of functional flexibility, users can customize their measurement requirements according to the definition of various sensors. AMIDA 2020XP CIS tester is a new generation of CMOS Image Sensor dedicated tester, which integrates DC open/short/leakage test, AC Pattern test and image test. It uses 180 Pin high-speed cable to connect to the test end
-
Product
Torque Tester
DI-9M-8/08
-
Ideal for daily inspection of electric screwdrivers. Uses OW joints that do not require rewinding. Five channels of pass/fail judgment conditions can be saved, and settings can be made simply by switching channels even if the tightening conditions change. Efficient measurement without rewinding by "OW joint".
-
Product
Insulation Testers
-
Kyoritsu Electrical Instruments Works, Ltd.
The insulation resistance (IR) test (also commonly known as a Megger) is a spot insulation test which uses an applied DC voltage (typically either 250Vdc, 500Vdc or 1,000Vdc for low voltage equipment <600V and 2,500Vdc and 5,000Vdc for high voltage equipment) to measure insulation resistance in either k, M or G.
-
Product
Thickness Tester
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
The coating thickness gauge is designed for non-destructive, fast and precise coating thickness measurement.
-
Product
SAFETY TESTERS ( CURRENT LEAKAGE TESTERS )
ST-05
-
Safety Tester Model ST-05 is a test set for testing small equipment powered by 120V 60 Hz, from an approved U-ground source. Test also can be run on double-insulated tools an on appliances with two-pin parallel plugs.
-
Product
DSE Wire Testers
-
DSE Test Solutions your gateway to a world of wire technology.We supply high-quality test equipment for the wire and cable industry. Our extensive range of intelligent test equipment is used for quality control and production optimisation of enamelled wire and cable.
-
Product
Box Compression Tester
BCT-03
-
Jinan Leading Instruments Co., Ltd.
BCT-03 Box Compression Tester is professionallyused to test the compression resistance property of carton box, corrugated box,honeycomb cardboard box and other packaging. And it’s also applicable tocontainer compression test of plasticbucket (edible oil, mineral water), fiber drum, carton, paper, cans, containerbarrels (IBC barrels).
-
Product
Automatic Battery Testers
-
T100BT is an innovative, modular battery testing equipment able to combine, on a single test platform, all the tests required to detect any possible defect on battery cells and modules: from defective cell wiring, to geometrical or surface irregularities, to out-of-specs performances.The battery tester is designed for the high-volume production test of battery modules composed by prismatic, cylindrical, or pouch cells, as well in a Lab/NPI version for engineering, prototypes and low-volume battery testing. The complete configurability allows you to equip the tester with the modules and tools you need to test your products, reaching the desired throughput.
-
Product
Radio Vector Tester
-
Wuhan Sunma Technology Co., Ltd.
Radio & Vector Network Analyzer adopts the advanced digital and RF combination design technology, fundamental wave frequency mixing technology, digital IF processing technology, intelligent power management technology, etc. It comes with features of high precision, small size, light weight, battery power, can measure SWR, Return Loss, Cable Loss, Impedance, DTF, etc, is used to the field test of cable, feeder, and the reflection parameters test of RF components in science and teaching. SunmaFiber provide all kinds of CATV meters, such as Signal Level Meter, QAM Analyzer, Spectrum Analyzer, DVB/DVC/DVT Analyzer and other TV testers.
-
Product
IEC60065 Socket Torque Balance Tester Torsion Tester
-
Shenzhen Chuangxin Instruments Co., Ltd.
*Plug and Socket Torque Tester/Device is for compliance is checked by engaging the device, as during intended use, with the socket-outlet of a test apparatus. *Plug Torque Tester/Equipment is a device provided with pins intended to be introduced into fixed socket-outlets shall not impose undue strain on these socket-outlets.The balancing arm of the test apparatus pivots about a horizontal axis through the centre lines of the contact tubes of the socket-outlet at a distance of 8 mm behind the engagement face of the socket-outlet.*With the machine not in engagement, the balancing arm is in equilibrium, the engagement face of the socket-outlet being in the vertical position.After the device has been engaged, the torque to be applied to the socket-outlet to maintain its engagement face in the vertical plane is determined by the position o a weight on the balancing arm.
-
Product
Mini Lan Tester
21-8572-00
-
Auto decipher the straight and cross-over pinning?RJ45 each pair connected display.
-
Product
Roughness Testers
-
Roughness is an important parameter when trying to find out whether a surface is suitable for a certain purpose. Rough surfaces often wear out more quickly than smoother surfaces. Rougher surfaces are normally more vulnerable to corrosion and cracks, but they can also aid in adhesion. A roughness tester is used to quickly and accurately determine the surface texture or surface roughness of a material. A roughness tester shows the measured roughness depth (Rz) as well as the mean roughness value (Ra) in micrometers or microns (µm). Measuring the roughness of a surface involves applying a roughness filter. Different international standards and surface texture or surface finish specifications recommend the use of different roughness filters. For example, a Gaussian filter often is recommended in ISO standards.
-
Product
Initial Adhesion Tester
CZY-G
-
CZY-G Initial Adhesion Tester is suitable for pressure-sensitive tapes, medical patches, self-adhesive labels, protective films and other related products for initial tack testing.
-
Product
Network Tester
-
Shaanxi Aitelong Technology Co., Ltd
Devices that can be used to check network cables and network connections in the Ethernet.
-
Product
Servo Tester
105
-
Simulates a receiver so you can test your motors and servos without having to use a transmitter and receiver. It can send RC-PWM signal of 1ms to 2 ms in 20ms period. It connects to an ESC via three wires. The servo tester is powered by the BEC in your speed control or by a std 4 cell 5 volt receiver battery
