Showing results: 61 - 75 of 100 items found.
-
aTCA-3710 -
ADLINK Technology Inc.
The aTCA-3710 is a high performance, high bandwidth, 40G Fabric switch blade for AdvancedTCA® platforms. This product is ideal for bandwidth intensive telecom applications such as wireless access controller, DPI/security network, IPTV, IP multimedia subsystem, RNC/BSC, broadband access/bearer network, data center, and LTE/4G network applications. The aTCA-3710 provides 40GbE hub-to-node connectivity and integrated switch silicon that supports load balancing, priority queues, packet classification, and flow control to enable strict bandwidth management for implemented applications.
-
ROM-Elektronik GmbH
High- frequency loads come from the transmission systems of telephone companies (GSM, UMTS, LTE), cordless telephones (DECT telephones), wireless computer networks (WLAN, Bluetooth,...), and radar, radio, TV (DVB), etc. The blood is acidified by this influence and Cell membrane tensions change.
-
Algodue elettronica
UEM1P5-4D R for RS485 Modbus RTU/ASCII communicationUEM1P5-D M for M-Bus communicationUEM1P5-4D E for Ethernet (Modbus TCP) communicationFor 1 or 5A CTProgrammable CT ratioFully bi-directional four quadrants measurements for all energies and powersFor 3 / 4 wire networks with balanced or unbalanced load (UEM1P5-4D R and UEM1P5-4D E only for 4 wire networks)Class B according to EN 50470-3S0 output for energy pulse emissionAvailable with MID certification
-
KHZ43201 -
Beijing KeHuan Century EMC Technology Co,.LTD
The KHZ43201 voltage probe is a standard low resistance test probe, which meets the technical requirements for this product in the CISPR16-1 and CISPR14-1 test equipment. When measuring the interference voltage of the power grid, the artificial power supply network cannot be used at the load port, and sometimes it is necessary to use a voltage probe to measure the interference of the signal port, the load port, and the antenna port. The input impedance of the voltage probe to the ground wire is greater than 1.5KΩ, which can protect the input terminal of the receiver.
-
TE3000-series -
LBA Group, Inc
The TE3000-series of RF vector network analyzers have full vector measurement capability, and accurately resolves the resistive, capacitive and inductive components of a load. The user can display the vector impedance plus a range of related parameters including SWR, reflection coefficient, return loss and R-L-C equivalent circuit.
-
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Network analyzers are used to measure so-called scatter parameters (S-parameters). These describe the behaviour of electrical components with the help of wave magnitudes. Whether simple cables, filters, amplifiers or complex subsystems, the following applies to all these components: Different loads can have unseen effects on the measured values over time.
-
BIDOYNG -
Kelvatek Ltd.
BIDOYNG fits into existing LV fuse positions using two LV fuses in parallel, creating a robust single-shot auto-recloser. The primary fuse carries the load current until a fault causes it to operate. Then, after a user programmed delay, the secondary fuse is switched in and the network re-energised without customer interruption.
-
F-SIM-LDR-615A -
Avionics Interface Technologies
The F-SIM-LDR-615A software application is an ARINC 615A data loader tool which is compatible with AIT’s family of ARINC 664 interface modules and standard LAN interfaces available on most PC’s. The F-SIM-LDR-615A application supports ARINC 615A load operations over Ethernet and ARINC 664 networks.
-
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Rosenberger offers the following types of calibration kits with a range of coaxial connector series for vector network analyzers (VNAs). All Rosenberger calibration kits can be used from DC to their maximum frequency. Full version with adaptors and sliding loads for variable measurements Industrial version for standard measurements LRL and TRL version
-
SIP Tester™ -
StarTrinity.com
StarTrinity SIP tester™ is a VoIP load testing tool which enables you to test and monitor VoIP network, SIP software or hardware. It is able to simulate and passively monitor thousands of simultaneous incoming and outgoing SIP calls with RTP media, analyze call quality and build real time reports.
-
Suzhou 3ctest Electronic Co.,Ltd.
High-end test instrument of EFT/Burst for new energy, which fully comply with CE and CCC certification. With a built-in three-phase five-wire automatic coupling /decoupling network EFTN 69100T, it can meet the requirements of new energy test system and high power load test. It is featured with good reliability, stable performance and easy use.
-
Mors Smitt Group
XM-series modular electronic monitoring relays *Voltage montoring models (1-phase or 3-phase) *3-phase network monitoring models (phase failure, sequence and asymmetry) *Current monitoring models (AC, DC) *Suited for 35mm rail (DIN) mountingFor general purpose, industrial applications, switching of AC or low DC voltages / resistive loads.
-
PerfectStorm ONE 1GE/10GE Appliance -
Keysight Network Applications and Security
PerfectStorm ONE facilitates network and security proof-of-concepts (POCs) and assessments, all in a compact device. This POC-in-a-box enables enterprises and service providers to select optimal devices and right-size data centers, as well as providing device vendors with a platform to fully showcase their product’s performance, resiliency, and throughput under realworld traffic loads.
-
NDB-DOC-3™ -
ndb Technologies Inc.
The NDB-DOC-3™ is a test instrument designed for distribution networks transformers from 5kVA to 3MVA. It can determine the presence of short circuits or open circuits in the distribution transformer primary winding & also short circuits on the secondary winding.The NDB-DOC-3™ is designed to be operated without disconnecting the transformer’s secondary windings from their loads.
-
Lifasa - International Capacitors, SA
The batteries of capacitors for automatic AT are designed for those applications in which the power levels in the AT network are variable. This type of equipment, with a number of steps normally between 2 and 4 to avoid phenomena in the installation resulting from the connection and disconnection of the capacitors in the electrical network, is controlled by a type MCX regulator, which tunes and regulates the input of the steps according to load levels, taking into account the expected waiting times of AT that between consecutive connections is 600 s., this time we can reduce it to less than 10 s. if we install TP for fast download.