Network Load
-
product
Auto Calibration for Load & Extensiometer
Jinan Testing Equipment IE Corporation
TE electronic calibration module provides an easy way to calibrate load cell or extensometer and signal conditioning electronics without using a mechanical calibrator. It enables performing on-site electrical calibration and easy to periodically “spot check”, which will help ensure that the load cell and the extensometer and electronics are calibrated correctly.
-
product
Coupling Decoupling Network
TBCDN-M4
The TBCDN-M4 is a Coupling Decoupling Network for conducted immunity testing according to IEC 61000-4-6.
-
product
USB And Network Cable Tester
PinMaster PK-2018/2020
The PinMaster is designed to quickly and easily check all types of USB cables (USB 2.0, 3.0, A, B, 2.0 mini B and 2.0/3.0 micro B) and common cabling system includes Network/Data, Telephone/Voice and Coaxial/Video cables.
-
product
LED Load Simulator
63110A/ 63113A/63115A
As shown on the V-I curve in figure 1, the LED has a forward voltage VF and a operating resistance (Rd). When using a resistor as loading, the V-I curve of the resistor is not able to simulate the V-I curve of the LED as shown in blue on figure 1. This may cause the LED driver to not start up due to the difference in V-I characteristic between the resistors and the LEDs. When using Electronic Loads, the CR and CV mode settings are set for when the LED is under stable operation and therefore, is unable to simulate turn on or PWM brightness control characteristics. This may cause the LED driver to function improperly or trigger it’s protection circuits. These testing requirements can be achieved when using a LEDs as a load; however, issues regarding the LED aging as well as different LED drivers may require different types of LEDs or a number of LEDs. This makes it inconvenient for mass production testing.
-
product
48V / 200 Amp Load
BD12-48P
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
product
PNA Network Analyzers
The PNA Series of network analyzers offers industry-leading performance for testing amplifiers, mixers, and frequency converters. Built-in pulse modulators and pulse generators provide pulsed S-parameter measurements quickly and accurately. All models are available in two-port single-source and four-port dual-source versions.
-
product
Embedded And Networking Processors
From communications processors that enable a broad range of networking applications to embedded processors that drive consumer multimedia applications, Broadcom leads the industry with a broad range of cutting-edge processor products. Our knowledge-based processors deliver flexibility and scalability to address the needs of a large landscape of networking applications and our secure processors deliver better protection of personal information or sensitive corporate data.
-
product
Network Security Appliances
Full range network appliances for applications such as NGFW, UTM, DPI, IDS/IPS, comes with scalability, modular design, reliability & manageability.
-
product
AC Load Banks
K-1000 Series
Kongter Test & Measurement Co., Limited
Load bank testing is vital to replicate and verify the operation of critical backup power systems such as diesel generators and uninterruptible power supplies (UPS). Kongter offers a wide range of customer-tailored AC load banks that excel in a range of load test applications and environments.
-
product
Real-Time Ocean Sensor Network
Powered by the Sofar Spotter network: the largest real-time ocean sensor network in the world. Save on fuel and costs while leaving a smaller footprint on the planet.
-
product
RF Match Networks
Enable fast, accurate, and reliable matching. Advanced Energy’s match networks expertly perform in multiple power ranges. Available in plug-and-play models or configurable units, easily install, expedite tuning, and tighten process control.
-
product
Wireless Network Firewall and Switch
AWSNS
AWSNSWireless Network Firewall and SwitchAvaLAN’s Secure Networking Service “SNS” is an affordable centralized managed service that provides top-level security whether it’s for a single site or mega-site enterprise. This service manages your PCI compliance from the store and into your forecourt. It is the ideal service for monitoring and maintaining your store's critical network infrastructure and also offering LTE Failover and WiFi capability. This cloud-based management means large network changes can be made quickly and easily even if it’s to thousands of sites. AvaLAN’s Secure Network Service takes the pain, hassle, and complexity out of your data network so you can focus on your business and your customers.
-
product
High Precision Electronic Load
PEL-8000
PEL-8000 series adopts high-performance chip high-speed and high-precision design, providing resolution of 0.1mV, 0.01mA (basic accuracy is 0.03%, basic current rise rate is 2.5A / US)
-
product
Network Cable Tester
PA-40
The PA-40 is designed to check both shielded and unshielded twisted pair (STP/UTP) and coaxial BNC-type network cables. With the push of a button, it tests all wires for continuity, miswiring, and polarization. Dual-colored LEDs let you identify correct and reversed pairs; using the included remote unit, cables may be tested before installation or after installation. Features tip/ring polarity test. Uses 1 9V battery.
-
product
Waveguide Loads
Smiths Interconnect offeres high power Waveguide loads that can with stand up 200Watts at 18 GHz
-
product
Load Cell Indicator
Morehouse Instrument Company Inc.
This indicator can read mV/V and use free, custom Morehouse software to convert the mV/V units to engineering units with coefficient files from ASTM E74 or ISO 376 reports. This meter is often the choice for accredited calibration service providers that want high accuracy and convenience but do not want to break the bank.
-
product
RF Waveguide Load
RF Lambda’s waveguide loads are used at end of an RF signal chain to provide a good 50ohm match and dissipate any RF energy into heat. They are available in a variety of power levels and offer low VSWR.
-
product
Electronic Loads
PeakTech Prüf- und Messtechnik GmbH
Can be used for important test procedures in quality assurance as well as e.g. testing of power supplies and control units, batteries, fuel and solar cells. For precise load control for various purposes, this device offers load control according to constant voltage (CV), constant current (CC), constant load resistance (CR) or constant power (CP) with a highly precise resolution of 1mW, 1mV, 1mΩ and 1mA. The device also offers additional test modes, e.g. the battery test or the dynamic test. The PC interface and software offer the option of implementing freely programmable test sequences with data evaluation.
-
-
product
Mesh Network System
BR-400AN
BR-400AN uses Silex's enhanced IEEE802.11s implementation to not only making it easier to construct a mesh network, but also improve and enhance the network stability and performance.
-
product
Dual DC Electronic Load
3330F Series（40W~250W）
3330F Series Dual DC Electronic Load is a two load unit in one module. Each 3330F Series module has its own control and display panel, CC/CR/CV/CP/ Dynamic modes, plug in 3300F with 150 sets Store/Recall memory which provides load set-up more efficiently，also can be remote controlled via RS232、Ethernet、USB and GPIB interface.
-
product
USB Network Gate
With USB Network Gate you will never experience any issues accessing and using the USB devices that are plugged into remote computers. You can work with those devices as if they were physically connected to your local machine. All that is needed to do for that is install USB over Network Connector on the computer with USB device physically attached (server) and on the computer where you want to use this device (client). USB over IP Connector will do all the rest. No additional hardware needed! BTW you can choose whether Mac, Linux or Windows machine will be a client or a server.
-
product
Network Configuration Management
NCM
Motadata Network Configuration Management (NCM) organizes and maintains critical network configurations of each and every component of the IT network infrastructure. The IT teams can repair, modify, configure or upgrade devices remotely with NCM. Reduce the time required to manage critical network changes and repetitive manual tasks across complex, multi-vendor networks with network automation. The platform is pre-integrated with well-known network device vendors like Cisco, HP, Juniper, D-Link.
-
product
1U Rackmount Network Appliance Platform
NA591
The NA591 is an advanced 1U rackmount network appliance platform with a maximum of thirty-four LAN ports. This high-performance network appliance system is powered by the Intel® Xeon® E-2200 and 9th/8th gen Intel® Core™ i7/i5/i3 processors with the Intel® C246 chipset. The NA591 comes with four expandable LAN module slots that support 1GbE/10GbE/25GbE/40GbE/Fiber/Copper/LAN Bypass interfaces, greatly enhancing its flexibility and scalability. This scalable 1U network appliance platform delivers security, stability and reliability for VPN, firewall, network bandwidth controller, WAN accelerator and surveillance system applications. This outstanding network security appliance features Intelligent Platform Management Interface (IPMI) to allow administrators to monitor system health and manage systems. Trusted Platform Module (TPM) is supported to bolster hardware-based data protection. Moreover, it features latch-type LAN Bypass functions for fail-over option as well as featuring BIOS console redirection. The NA591 is an ideal platform for network security, cloud computing and data centers applications.
-
product
Load Cells
Load cells are electronic weight sensors whose purpose is to receive the electrical excitation caused by a certain weight applied to the scale or balance and transmit it to a weight indicator . The load cell is an essential component in any scale or electronic balance and they come in different models and specifications. A Wim load cell is essential for a weighing system where precision, durability and a fair price are required. WIM-Systems manufactures a wide variety of load cell models, one for each need, in addition to offering all the advice you need to choose the model that best meets the particular needs of your weighing system and always backed by WIM-Systems quality and technology.
-
product
In Line Load Cell (10KN-50KN)
106, 107, 108 Series
Miniature Threaded in Line Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type measures tensile and compressive loads up to 50kN and 10klb with better than ±0.5% non-linearity. This type is also available with fully welded cover.
-
product
DC Electronic Load
63600 series
Chroma's 63600 series DC electronic loads are designed for testing multi-output AC/DC power supplies, DC/DC converters, chargers, batteries, server power supplies, and power electronic components. They are excellent for research, development, produc t ion, and incoming inspection applications. The 63600's state of the art design uses DSP technology to simulate non-linear loads using a unique CZ operation mode allowing realistic loading behavior. The 63600 series can draw its rated current under very low voltage (0.4V typical). This unique feature guarantees the best loading performance for modern Point-of-Load conditions and fuel cells.
-
product
Mechanical Load Tester
Solar modules and collectors, whether on roofs, in façades, or freestanding, are often exposed to high mechanical stress or load: A deep layer of snow or strong winds can greatly affect the materials and connections. Mechanical load test stands accurately test the durability of PV modules and thermal solar collectors.
-
product
Load Cell Amplifiers
Datum Electronics load cell amplifier range is designed to increase (or amplify) a signal, generated by a strain gauge load cells with a full bridge connection, pressure transducers or torque sensors, allowing the user to use the data from the load cell in a more efficient and productive way.
-
product
Access Network Diagnostics
As fiber networks are built and services scale, Fiber Diagnostics helps Service Providers manage their customers’ experiences by ensuring successful installation and service start up, while decreasing time to revenue. Once the fiber network is in service, Enghouse Fiber Diagnostics assures customer satisfaction through improved customer service and rapid time to repair, while reducing operational costs.
