Network Load
-
Product
High Current DC Load
3350F Series
-
3350F has its own control and display panel, CC/CR/CV/CP/Dynamic modes, 150 sets Store/Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB, RS232、USB and LAN interface.
-
Product
Low Profile Compression Only Load Button Load Cell with Mounting
LBM SERIES
-
The LBM Series (Load Button) load cells are offered for compression only applications where space is limited. This load button is a direct replacement for many of the same type and bolt patterns currently used in the industry. The matching surface must be flat and at least 2 inches in diameter. The loading diameter is slightly convex for accurate load distribution. Eight threaded mounting holes are provided on the bottom surface for fastening down from beneath. These sensors are manufactured from heat treated 17-4ph stainless steel, and the sensing element incorporates bonded foil strain gages of the highest quality. They are sealed for protection against most industrial environments.
-
Product
Network Cable Tester
LightingJoG Rack 8
-
Sensational 19 inch 2U rack mount Lighting/Network cable tester with SINGLE & DOUBLE ended testing, memory and intermittent fault detection.
-
Product
Phantom Load Test Set
-
Is a testing accessory, wisely designed for field testing service. This equipment helps in providing artificial load that is unaltered by the change in power supply.
-
Product
Copper Network TAPs
-
Network test access points (TAPs) are a hardware tool that allows you to monitor your network. Garland Technology offers copper network TAPs in network speeds of 10/100M or 10M/100M/1000M (1G). Copper TAPs are purpose-built hardware devices used for out-of-band monitoring tools and make a 100% copy of your networks data allowing your monitoring tools to see every bit, byte and packet.®
-
Product
Network Interface
-
VadaTech offers AMC Network Interface Cards (NICs), FMC networking modules and ATCA rear transition modules (RTMs) with a wide range of connector interfaces to make it easier for you to integrate an embedded computing system into your solution.
-
Product
Satellite Network Simulator
-
The DataSoft Satellite Network Simulator is a real-time software tool capable of simulating satellite links by operating as a hardware-in-the-loop tool for layer-2 verification and validation, or, as an offline planning tool for capacity and availability analysis for planned deployments.
-
Product
Interface And Load Box
MS 3646I
-
Interface and Load Box is standard portable 19” rack mountable unit. It is customized unit for single channel tester of IFCC. This unit has cable/harness interface between CPCI System and IFCC LRU. This box also houses all actuator loads and switching circuits.
-
Product
Network Probe for TC-NT2
TC-TP1
-
TRENDnet´s TC-TP1 is an easy-to-use amplified inductor and tone probe that is used for tone tracing and line testing. The TC-TP1 features a simple push button that provides easy operation and conserves battery power. This ergonomically designed device comes with adjustable volume control and signal LED for enhanced accuracy in noisy environments.
-
Product
Vector Network Analyzers Handheld
-
Wireless VNA Master + Spectrum Analyzer, the industry's broadest frequency handheld solution to address cable, antenna, component and signal analysis needs in the field: with frequency coverage from 5 kHz to 6/20 GHz.
-
Product
AC and DC Electronic load
63800 series
-
The Chroma 63800 Loads can simulate load conditions under high crest factor and varying power factors with real time compensation even when the voltage waveform is distorted. This special feature provides real world simulation capability and prevents overstressing thereby giving reliable and unbiased test results. The 63800's state of the art design uses DSP technology to simulate non-linear rectified loads with its unique RLC operation mode. This mode improves stability by detecting the impedance of the UUT and dynamically adjusting the load's control bandwidth to ensure system stability. Comprehensive measurements allow users to monitor the output performance of the UUT. Additionally, voltage & current signals can be routed to an oscilloscope through analog outputs. The instrument's GPIB/RS232 interface options provide remote control & monitor for system integration. Built-in digital outputs may also be used to control external relays for short circuit (crowbar) testing.
-
Product
AC & DC Electronic Load
3270 Series （350V,1875W~22500W）
-
3270 Series is suitable for the step, square and sine wave of the AC Power device test, especially for the uninterruptible power supply UPS, Inverter, fuses, circuit breakers, power regulator AVR, battery, AC / DC power supply / components ... and so on, absolutely is the best test solution in the market.
-
Product
Miniature S-Beam Load Cell
500 Series
-
The Miniature S-Beam Load Cell is a bi-directional Aluminium strain gage based transducer with high performance and builtin temperature compensation. This design provides better than ±0.1% (full scale) non-linearity and includes overload protection in both tension and compression directions. Options include IEEE1451.4 TEDS capability.
-
Product
Canister Load Cells
-
PCB's cost-effective canister load cells are easy to install and ideal for low-capacity applications. Canister style load cells include a built-in mounting base for a simplified installation in both tension and compression applications.
-
Product
DC Electronic Load
-
DC electronic loads are designed for testing a wide range of power conversion products including AC/DC and server power supplies, DC/DC converters, EV batteries, automotive charging stations, and other power electronics components. These units can be synchronously paralleled up to 240kW and dynamically synchronized for generating complex multi-channel transient profiles. The 300% peak overpower capability provides extra headroom for fault condition simulations in automotive batteries, fuel cells, and more.
-
Product
AC & DC Electronic Loads
-
The Adaptive Power Systems Electronic Loads cover a wide range of power levels, voltage and current profiles and feature sets.Supported voltages range up to 1250Vdc or 350Vrms AC. From bench to system and DC or AC requirements, we can more than likely offer you the optimal programmable load to meet your needs.
-
Product
Network Performance Testing
FortiTester
-
FortiTester helps enterprises and service providers maintain the most secure and resilient infrastructure through continuous validation of effectiveness and performance. With network performance testing and breach attack simulation (BAS), it assesses the people, processes, and technology on which the security of an organization depends.
-
Product
Filtering Network TAPs
-
Filtering network TAPs allow you to filter out the packets and traffic that is not needed by the tool to perform its function. Filtering ensures that monitoring ports do not become oversubscribed with unneeded data. Filtering TAPs are purpose-built hardware devices that let you see every bit, byte and packet.®
-
Product
Computer Networking Solutions
-
Today’s world has a never ending appetite for data. Everywhere you look there are connected devices that provide and consume that data at an astonishing rate, and the demand increases every day. Our computer and networking customers are constantly pushing the edges of technology to deliver data faster and more reliably than ever. They use the newest electronics available to keep our data flowing – data that is critical to the operation of the world’s infrastructure. As cutting edge technologies are developed, these faster more advanced capabilities require the most sophisticated testing available. Circuit Check is constantly evolving our test fixtures and systems to meet this industry’s most advancedrequirements.
-
Product
Low Profile Compression Only Load Button Load Cell with Mounting Holes
LBC SERIES
-
The LBC Series (Load Button) load cells are offered for compression only applications where space is limited. The matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Counter bored mounting holes are provided for fastening down from the top. These sensors are manufactured from heat treated 17-4ph stainless steel and sealed for use in most industrial environments.
-
Product
XR Resistive Reactive Load Banks
-
Mosebach Manufacturing Company
Mosebach’s XR series load bank offers you a range of options for resistive reactive loads in both lower voltages of 480 and 600 or MV at 4160 and higher. Outdoor rated user friendly for years of use.
-
-
Product
Power Networks Test
TX6000
-
The TX6000 is a hand held Time Domain Reflectometer with 11 range scales covering the range 0-6000 meters, with a 7 mater first range scale and a 0.5 meter dead zone near and far end faults are clearly displayed on its 128×64 pixel back light Liquid Crystal Display.
-
Product
Outdoor Permanent Mounted Load Bank
-
Mosebach Manufacturing Company
Mosebach Pad Mounted Load bank is designed to be permanently mounted next to a generator for dedicated testing. Its unique design allows it to be one of the smallest on the market! This size enclosure will fit 50 kW, 75 kW or 100kW of testing ability. Also available in 300kW and larger load banks.
-
Product
AC Load Banks
-
Guangdong EMAX Electrical Co., Ltd.
We offer AC load banks in a variety of capacities and any voltage combination, with custom models including resistive, inductive, capacitive or resistive/reactive combination loads, all tailored to meet any load testing requirement.
-
Product
Resistive Load Banks
R Series
-
Load banks are devices which contain resistive, inductive and/or capacitive loads, apply the load to an electrical power source and dissipate the power of the electrical source. Portable and stationary resistive load banks incorporate as low as 1 kW load step increments for testing small to large generating sets. The fine control resolution ensures accurate load control and power factor targeting adjustments.
-
-
Product
PXIe-S5090, 9 GHz PXI Vector Network Analyzer
787251-01
Vector Network Analyzer
PXIe, 9 GHz PXI Vector Network Analyzer - The PXIe-S5090 is a 2-port Vector Network Analyzer (VNA) that helps you measure amplitude, phase, and impedance. You also can use the PXIe-S5090 to perform time-domain analysis and to calculate the S-parameters of 2-port RF devices. It features a 300 kHz to 9 GHz frequency range, a wide dynamic range, and high sweep speeds for automated design validation and production test. Additionally, the PXIe-S5090 supports automatic precision calibration, full vector analysis, and reference plane extensions.
-
Product
Device Networking
-
Offers complete control of how and when the application can discover, connect, disconnect, and get status from the USB device across the network.By integrating the SDK, you can create your own user interface and make it work seamlessly with your application.The SDK supports searching device servers on the network.Supports getting information and status from the USB device server.
-
Product
Network and Application Monitoring
IxChariot
-
Instant performance assessment of complex networks from pre- to post-deployment
