-
product
Digital H.V. Insulation Tester(12kV)
7012 IN
Standard Electric Works Co., Ltd
● Protection class: IP66 (Lid closed)● Test insulation resistance up to 20TΩ (20000GΩ).● Short-circuit current up to 5mA● Microprocessor controlled.● 24 insulation test voltages : 500V, 1kV, 1.5kV, 2kV, 2.5kV, 3kV, 3.5kV, 4kV, 4.5kV, 5kV, 5.5kV, 6kV, 6.5kV, 7kV, 7.5kV, 8kV, 8.5kV, 9kV, 9.5kV, 10kV, 10.5kV, 11kV, 11.5kV, 12kV ● AC/DC voltmeter (600V)....show more -
product
Network Infrastructure Testing
Xena VulcanBay
Xena Networks’ VulcanBay is a scalable Gigabit TCP test chassis that offers extreme performance for stateful traffic load testing, analysis and characterizing of Ethernet equipment and network infrastructure. It supports 1/2.5/5/10/25/40GE interfaces and can be used for simulating millions of real-world end-user environments to test and validate infrastructure, a single device, or an entire system.
-
product
Permeation Analyzers
MOCON Permeation Analyzers are used to test the gas permeability of packaging films and whole finished packages. Our analyzers provide Oxygen Transmission Rate (OTR) and Water Vapor Transmission Rate (WVTR) testing capabilities for a diverse range of materials and packages. MOCON Water Vapor and Oxygen Permeation Analyzers offer the highest repeatability and lowest limits of detection for OTR and WVTR measurements. This means better QC of your packaging processes and higher confidence in your R&D results.
-
product
Multiple Output Bidirectional PSU
LAB-MOBI
Electronic Test & Power Systems
The LAB-MOBI is a series of multi channel High Power Bidirectional PSUs. Each system is able to operate as either a DC Source or a DC Electronic Load. This integrated approach features high dynamics enabling the user to switch seamlessly between quadrants. When sinking energy from the unit under test the LAB-MOBI automatically inverts the DC to AC and synchronises this output to the grid. Dedicated application modes are available for battery cycling and emulation, which can be used to implement ...show more -
product
ADI Test Fixture
TA-6500
The TA-6500 test fixture combines the features of the OEM's Instrument Servo Tester(T307962), the Pointer/Flag Test Fixture(T307951) and the AD-650/600 Test Panel(T334043) all into one panel to facilitate testing of these Attitude Director Indicator's. The panel switches and adjustment pots are labeled to match the test procedure numbers and the duplicity in marking makes it easier for the technician to understand each function. The UUT interface is through a 96 pin zero insertion force(ZIF) typ...show more -
product
Protection Relay Testing
ARTES
Compact, powerful relay test systems for carrying out highly complex tests with ease and precision. The test systems of the ARTES product line are used to carry out functional tests on all types of protection devices, including DT/IDMT relays, distance protection relays and differential protection relays, to ensure that they function correctly. More than 20 years of experience in developing and manufacturing automatic relay test systems have gone into creating the fourth generation of ARTES test instruments.
-
product
Doble Test Assistant Software
DTA Software
Doble Test Assistant software is your comprehensive software tool for the collection, analysis and management of test results for the Doble M-Series family of instruments.DTA is a trusted and intelligent software platform that takes asset testing and data analysis to the next level. DTA is available in a Basic or Professional version depending on your testing needs.Professional versions of the software include features such as the First Response ANalytics Knowledgebase. FRANK is an artificial intelligence system that "thinks", helping you instantly analyze your test results along with clear recommendations and explanations.
-
product
Twin columns automated force test stand 48" travel - 10,000 lb
710TN
The advanced 710TN Series Universal Test Systems are ball screw driven test stands, excellent for affordable, precision tensile and compression testing of a wide variety of materials, products or ASTM standards. These variable speed testers have increased speed ranges and include adjustable travel limit switches. With the unique dual testing area, users can setup for two tests, tensile and/or compression, without having to switch out fixtures.
-
product
Fully Automatic Rubber Tensile Testing System
Compactly Integrating Functions Required for Quality Control of Rubber Shimadzu Fully-Automatic Tensile Testing System This system provides full automation, from measurement of specimen dimensions, supply to the testing machine, and fixing of chucks to measurement of extension between standard lines and data processing. The system can be used for continuous nighttime testing, which helps save labor costs.
-
product
Optical Fiber Tensile Jig
This jig is designed for tensile testing optical fibers and other brittle fibers. The jig consists of upper and lower pneumatic flat grips with flat grip faces followed by large-diameter capstans.
-
product
High-Voltage Test Hood
HVE900
The large, bright test room with a ball-bearing cover is designed for high production quantities. Thanks to the easily exchangeable exchangeable plate, retrofitting for testing different products is also a simple task. Product properties: External dimensions (W * D * H) approx. 940 * 716 * 640mm Usable test space (W * D * H) approx. 750 * 500 * 460mm Contacting Installation space approx. 100mm high under removable plate Dielectric strength min 10kV Application area up to 2000m above sea level Po...show more -
product
PXI Strain Gauge Simulator Module 2-Channel, 3k
40-265-102
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 3kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
Judder testing machine
This machine is used to measure and evaluate friction characteristics such as temperature, frictional force, sliding velocity, etc. of steel plates, friction materials, ATF and additives of wet clutches.
-
product
Mobile Battery Scanner
CS-4001/127
Our CS-4001/127 is the perfect mobile test system for periodic battery testing. In combination with an electronic load, the condition of a battery system (SOH) can be determined exactly during a capacity test.
-
product
Bidirectional DC Power Supply
62000D
Chroma 62000D programmable bidirectional DC power supplies provide both power source and load characteristics. These two quadrant power supplies allow power from the DUT to be converted back to the utility grid and so are ideal for testing renewable energy power systems such as PV, storage, and EV inverters as well as a wide range of bidirectional power conditioning system (PCS) and may also be used as a battery simulator.
-
product
Professional Cable Tester
1EA560
Multifuncional tester with LCD display enables to show wire maps and combination of pairs and their lenghts. It also measure the lenght until the broken line / cable. It is suitable for CAT5, CAT5E, and CAT6 cables. With special interface is also suitable for testing of coaxial and telephone cables. It has special unit for testing of cable ends in the other room.
-
product
High Voltage Pulse Attenuators
Barth High Voltage Pulse Attenuators are matched impedance coaxial attenuators for use primarily in pulsed 50 ohm systems, or where occasional transients would damage ordinary units. The attenuator design closely matches the impedance around each resistor, to that resistor. These attenuators feature an input impedance very close to 50 ohms, with characteristics as good or better than most microwave attenuators. These units are ideal for use in nuclear and high energy experiments. Extensive testing during manufacturing insures very high reliability for single-shot experiments. A voltage coefficient of the resistive film of less than .0001 %/V allows low voltage calibration of most systems.
-
product
O.N.E. Platform
O.N.E. platform allows to connect any HW component to any SW component independently of a vendor. With this data distribution and scheduling framework the user can build HW/SW architectures of any complexity. „Testing & Validation Phase“ and „Real World Deployment“ are covered by the O.N.E. technology. This results in ONE single environment for development and for productive systems at big scale.
-
product
Multi-Tone Test Systems
AR RF/Microwave Instrumentation
AR’s state-of-the-art multi-tone systems are designed to test RF Radiated and Conducted Immunity faster than ever before. Both the MT2IEC10V3M and MT4IEC10V3M fully comply with IEC 61000-4-3:2020 Edition 4, allowing for multiple tone testing, reducing test time by up to 74%. Commercial, aviation, and automotive industries, will perform RF radiated and conducted immunity testing faster, more accurately, more efficiently, and more closely to a real-world environment.
-
product
Heavy duty pull tester for roofing - 1000 lb
FIXUROOF 1000
The Fixuroof 1000 portable pull-tester is an accurate unit, designed for testing in the field the pull-out force for base ply fastener. Easily determine whether the mechanical fastener provides sufficient resistance to static uplift force to meet the wind load requirements.
-
product
DC Holiday Detector
Elcometer 236
The Elcometer 236 Holiday Detector provides high voltage porosity testing to detect pits, flaws, holes, etc. in a wide variety of non-metallic coatings.
-
product
Multicom Tester
IQ2010
The LitePoint IQ2010™ is a comprehensive, one-box test solution for all your connectivity testing needs:WiFi, 802.11a/b/g/n and 802.11pBluetooth, Classic (1.x, 2.x, 3.0) and Low Energy (4.0)GPSFMMIMOWiMAXZigBee
-
product
Altitude Test Chambers
Altitude chamber testing is important for manufacturers of products that might be shipped via air. It is especially important for defense and aerospace applications where pressure and vacuum conditions are even more intense. Our altitude test chambers simulate a variety of environmental conditions including temperature, altitude, humidity, and vibration for the rigorous testing standards of combined environment.
-
product
Low Voltage High Current DC Electronic Load
N62400 Series
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N62400 series is developed based on NGI's years of experience in testing for fuel cell. It is with high accuracy, high reliability and high cost-effective. N62400 series is with high power density and elegant appearance, which is available for benchtop use or installation in 19 inch cabinet.
-
product
Professional Handheld
ST5S
*Built-in high-precision LCR probe*Convenient one-hand operation*Ideal for Surface Mount Devices*Automated component identification*Automated test range selection*Manual C, R, L, Z and ESR modes*Test signal levels 0.5 and 1.0Vrms*Swiss-made precise test leads*Diode Polarity/Short Testing*Secondary D, Q, ESR parameters*Portable and ergonomic design*Built-in Li-Ion battery*Universal Micro USB charger*High visibility OLED display
-
product
ISO Test Charts
ISO has been the governing body for Image Quality Testing all over the world. To that end, APPLIED IMAGE is proud to be a participant in assuring that the industry has products that meet or exceed the requirements of ISO. Since ISO covers many levels, we provide test patterns of various types that can be used for Image Capture and Evaluation of Optical and Imaging systems of all types.
-
product
Mechanical Tester
NANOVEA Mechanical Tester is the most versatile nanoindenter and scratch tester capable of precisely measuring the micro- to nanomechanical properties of wide ranges of materials from thin films, coatings, ceramics and composites to polymers and bio materials via Indentation, Scratch and Friction testing. All NANOVEA Mechanical Tester models come with true feedback load control from independent load and depth sensors that provide unmatched accuracy and the highest repeatability available on...show more -
product
Digital (1kV below) Insulation Tester
1160 IN
Standard Electric Works Co., Ltd
● Measures insulation (MΩ), Continuity (Ω) and AC voltage.● Three insulation test voltages(DC V) : 250V, 500V, 1000V.● 3½ digital LCD (2000 counts).● 68 × 34mm ( 2.677” × 1.338” ) large LCD display.● LCD backlight display.● Automatic circuit discharge.● Test insulation at rated voltage into a 1mA load.● 200mA short circuit testing current for continuity.● Auto ranging.● Fuse protection.● Data hold function.● BS 16 edition.
-
product
PXI BRIC8 FIBO Matrix Dual 30x4 3pin brkout
40-595A-010
The 40-595A is a matrix module based on the BRIC format that is designed for fault insertion applications in safety critical testing. As with other BRIC modules the matrix size can be scaled to suit the user application. The 40-595 has a very high current rating of 10 Amps, ideal for higher power systems, and can be used as a conventional matrix.
-
product
Test Studio Dev Edition
Test Studio Dev Edition is a Visual Studio extension allowing software engineers to create functional automated UI tests in Visual Studio using C# or VB.NET. It is designed to provide ready-to-use Visual Studio automated testing functionality across web and desktop. Applications that are built with the Telerik and Kendo UI controls can be automated in a snap, by way of built-in native component translators.
