-
product
Bit Error Rate Tester
100G NRZ BERT
The C-BERT 2810-4 is a complete bit error rate tester dedicated for 100G Ethernet applications. The four independent channels enable an actual operating environment with traffic on all lanes. The simultaneous testing of 4 channels is much faster than testing each channel individually saving time and money. The BERT eye scan reveals low-probability events and shows the true performance of the DUT to aid troubleshooting. The high RF port density eliminates long cable length which degrades the sign...show more -
product
Optical Fiber Test Platform
Fiber Lab 3200
Fiber Lab 3200 from M2 Optics Inc. is a must-have solution for anyone developing or testing fiber optic products and systems. Available in two types of rack-mount chassis with up to 300km per unit, it offers the most professional approach for using fiber in the laboratory or network. In addition, it provides maximum protection against potential fiber and connector damage.
-
product
High Range UV Fluorescence SO2 Analyzer
Model N100H
Teledyne Advanced Pollution Instrumentation
The Model N100H instrument uses the proven UV fluorescence principle, combined with a state-of-the-art modular architecture, and intuitive operating software to provide accurate and dependable measurements of high range SO2 gas. The instrument includes interferent rejection, providing a simple and precise solution for a broad range of continuous emission monitoring systems (CEMS) and stack testing applications.
-
product
Event Detectors
EDH Series
Is designed to monitor electrical connectors undergoing reliability testing. This instrument detects nanosecond-range electrical resistance fluctuations characteristic of malfunctioning electrical contacts.
-
product
Transient Over-voltages Tester
SUG335
The SUG335 is a 1.2/50μs Transient Over-voltages Tester. The polarity interval time can be at least 1s. The standard voltage waveform complies with the IEC 60335, IEC61180, IEC 62052-11: 2003, IEC 61008-1: 1996, IEC 61009-1:1996 and IEC 60947-1: 1995, IEC60060, IEC1036 surge voltage test and has been used for safety testing to determine if the clearance was fulfilled the safety requirement while the transient voltage in the circuit.
-
product
Rack Based Test Solutions
Most equipment manufacturers and large enterprises prefer rack-based test tools as they are compact and higher density form factor solution for testing, monitoring, and troubleshooting network conditions. GL’s Multiple TDM Optical and Packet (mTOP™) rack enclosure can house any combination of USB based test equipment which are easily deployed and securely fixed to an equipment rack to provide extraordinary scalability to test switches, routers and end-to-end networks. These rack based pl...show more -
product
ST2817B+ LCR Meter (50Hz to 100kHz, 10 points))
ST2817B+ LCR meter is a high-performance and cost-effective measuring instrument. It can automatically measure the inductance L, capacitance C, resistance value R, impedance modulus |Z|, quality factor Q and loss tangent value D and other component parameters. The instrument combines powerful functions, superior performance and simple operation, which can not only meet the needs of high-speed measurement on the production site, but also meet the needs of precision testing in quality inspection, measurement, scientific research and experiment departments.Applications: Passive component / Other component
-
product
Industrial Battery Manufacturing
Analog Devices precision analog front ends and controllers for testing and monitoring battery cells simplify design by providing excellent accuracy, performance over temperature, flexibility with functionality, and overall reliability in a space saving package. Our devices measure battery charge/discharge current through precision fixed gain and programmable gain instrumentation amplifiers, and measure battery voltage via fixed gain and programmable gain difference amplifiers.
-
product
Thermal Vacuum Testing
When you want to test your product for extreme space conditions, that include temperatures from 155°C to -175°C at space vacuum altitudes, Environment Associates is your solution. Using this test to determine the unique failures of space mechanisms that orbit the earth is key in improving system reliability. Thermal vacuum testing is similar to thermal cycling but adds deep space vacuums for detecting corona/arcing and intermittence and increases a product’s out-gassing. The key failure modes fo...show more -
product
Innovative Testing
Originally founded as a test house, the IPTE Group today has in-depth knowledge in all areas of testing and test automation. Our internationally producing customer groups value our expertise in all areas of measurement and test technology as well as the often combined technologies such as software flash or optical test for their quality assurance.
-
product
IC Testing System
Is a system for giving electrical signals to a semiconductor device to compare output signals against expected values for the purpose of testing if the device works as specified in its design specifications.
-
product
PXI 3A Power MUX BRIC, 40-Channel, 6-Pole
40-571-405
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
Digital Earth Resistance Tester
ERT-1501
Electronic Digital Earth Resistance Tester is direct replacement of the conventional hand generator type tester. It is designed for measurement of the resistance of earthing used in the electrical equipment as well as for measurement of ground resistivity. It can be used for measurements of the other low regular and liquid resistances. It can also be used for measurement of voltage AC, voltage DC and resistance. This instrument finds wide application for testing earthing installation in power based industries, telecommunication networks and electrical traction systems etc.
-
product
Crossbar
For more complex test setups and signal switching, the CB-series crossbar matrix is an excellent choice. It allows testing of multiple UUT/DUT (units/devices under test) with many input/output signals or high speed communication buses without having to connect and disconnect them from the setup.
-
product
USB Modular Oscilloscopes
U270xA
Roughly the size of a paperback book, these low-cost USB oscilloscopes make it easy to perform essential measurements — waveforms, voltage, current, resistance, and more. Inject standard or arbitrary waveforms into the systems or devices you’re testing with Keysight USB oscilloscopes.
-
product
NI-9222 , ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
783283-01
±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9222 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The NI‑9222 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the NI‑9222: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
product
Digital Test Switch
FT-14D
Test switch solution for digital switchgear using current and voltage sensors. With the FT-14D Digital FlexitestTM switches, a new era of protection relay testing can be performed more safely, quickly and easily. The FT-14D switch allows a customer to integrate current and voltage sensors within digital switchgear and protective relays and thereby enable the Industrial Internet of Things.
-
product
EMC Testing
Does your product send or receive electromagnetic data? This can be analyzed using various tests. We investigate the interference immunity and emitted interference of simple electrical devices and complex machinery. Our EMC measurements and tests conducted in accordance with standards recognize all activity in the electromagnetic field and ascertain how immune to interference a piece of equipment is. We will also offer guidance on optimizing the product in terms of its EMC properties during the development phase.
-
product
Handset One Box Testers
Anritsu's handset one box testers offers multi-system service test platforms. These are high-speed measurement solutions used in production testing and design proving.
-
product
30KHZ Measurement Microphone
M30
Used on countless full-scale concert tours, as well as in scientific research laboratories, tropical rainforests, and rocket testing facilities, the M30 has proven to be a lab-grade audio instrument that can handle any environment.
-
product
Battery Module (60v-300v) Test System
Shenzhen Sinexcel RE Equipment CO., Ltd
The module test equipment adopts sinexcel advanced high frequency isolation scheme, and the detection process supports multi-gear switching. The equipment integrates voltage, temperature, pressure and other auxiliary channels, and can also integrate temperature box, water cooler and other equipment, 20ms high-speed working condition simulation and other practical innovative functions to meet all aspects of battery electrical performance testing.
-
product
FMC 5-Channel Digital I/O Module
FMC DIO
Sundance Multiprocessor Technology Ltd.
The fmc-dio-5chttla 5-channel digital I/O module is a simple board for digital I/O on LEMO connectors. It has been designed for testing White Rabbit functionality as part of the SPEC Demonstration Package for White Rabbit, and it can be used for other general purpose applications too.
-
product
Resonance Circuit for GIS Testing
CP RC
For HV testing OMICRON’s CPC 100 + CP RC are directly connected to the voltage transformer of the GIS, forming a resonance circuit. This reinforced “Power VT” is an integrated part of the GIS. So the need for draining and refilling any SF6 gas is eliminated. Acting as both the measuring and controlling device, the CPC 100 injects the required energy.
-
product
Memory Burn-in Tester
B6700 Series
B6700 can test as many as 48 burn-in boards in parallel at speeds up to 10 MHz, which helps memory suppliers get their newest products to market faster while also reducing testing costs. An original high performance chamber improves yield by assuring high temperature accuracy while generating high temperature. It also shortens the temperature rise and fall time which leads to shortening the test time.
-
product
Compatibility Testing
Cross-Browser Testing Ensures equal user visual experience Provides identical functional behavior of applications Cross-Platform Testing Ensures flawless product processing under different OS types, versions and locales Confirms seamless application functioning
-
product
Capacitive Discharge Testers
For IEC Testing of residual voltage after plug disconnect. The CDT-240 disconnects the line at the voltage peak and analyzes results to the requirements of various Standards, allowing quick results. Scope output for viewing decay waveform. Presets for EN 61010, EN 60065, EN 60950, EN 60601-1 and EN60335. Recommendations for Pluggable Type B equipment. NIST calibration supplied; A2LA calibration available. 16A option for testing large equipment.
-
product
Programmable Parametic Tester
IST 878
IST Information Scan Technology, Inc.
The IST 878 is a low cost test instrument that provides in-circuit or out-circuit testing for a wide range of discrete semiconductors
-
product
Strength And Hardness Testing
Strength measures how much stress can be applied to an element before it deforms permanently or fractures. Hardness measures a material's resistance to surface deformation.
-
product
3U VPX Bus Extension Kit PCIe Gen. 3
A PCIexpress bus extension kit permits a standard desktop PC to expand its available PCIe slots and is used as a system master for control of a VPX chassis for industrial applications in measurement, control and testing.
-
product
Ohmmetrie
0.1 Ohm to TeraOhms each ohmmeter or AOIP resistance meter covers a very broad spectrum of applications for resistance testing, electrical continuity but also isolation.
