-
product
RF Matrix Switch for Wireless Technologies up to 4 GHz
NEXUS-4
Quintech Electronics and Communications Inc.
The NEXUS-4 is a bi-directional fully non-blocking 3232 RF matrix switching system that can route any input ports to any outputs in a 6 RU chassis. With the frequency range of 700 MHz to 4 GHz and the capability of expanding to 256256, it enables large scale wireless testing that involves many MIMO base stations and devices. The built-in programmable attenuators and efficient automation interface provide ease-of-use testing of signal fade and emulation of mobility scenarios. It can dramatically increase lab efficiency by eliminating manual patch panel and cabling as it can be remotely reconfigured for different test setups consistently in seconds.
-
product
Relay Testing Voltage Source
PTE-FCL
It is the easiest and most economical way of increasing the relay types that can be tested with the PTE-100-C. The PTE-FCL upgrades the PTE-100-C to the PTE-100-C Plus model.
-
product
500 AMP Carbon Pile Load Tester
710
The #710 will perform variable load testing on 12 volt batteries rated as high as 1000 Cold Cranking Amps. Use this battery tester to simulate actual cranking loads. Also tests alternator charging voltage and relative starter current draw. The #710 features large dual meters to display the battery voltage and load current simultaneously, during the test.
-
product
PCI Precision Resistor Card 3-Channel, 2.5Ω To 773kΩ
50-297-143
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
DC High-Voltage Test Device
PGK 80
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PGK 80. The portable, one-piece PGK 80 high-voltage test device for generating negative DC voltage up to 80 kV is primarily used for onsite testing of paper-insulated mass-impregnated cables in the medium-voltage network. The high voltage is generated through a high-voltage transformer with secondary voltage-multiplier. The internal operating frequency of 20 kHz enables the smallest of device dimensions.* Continuous adjustable output voltage* The voltage measurement is done directly at the high voltage output* Timer of 1-30 min* Sensitive current measurement for recording the smallest of insulation currents with 6-time range switch, decadal
-
product
RelayDoc
RelayDoc makes testing relays easy. Simply plug in a relay and select test. No training required! RelayDoc tests all the important parameters of a relay against the manufacturer’s specification. Test reports are displayed on the touch screen and stored onboard for viewing and retrieval. They are also synchronised to a cloud database providing analysis and reporting tools.
-
product
Glass Vials Testing Equipment
Glass vials - as used in medicine - can be checked for vacuum before and after being put into storage.
-
product
Thunderbolt™
SCHILLER AUTOMATION GmbH & Co. KG
Thunderbolt™ test adapters and test fixture kits facilitate Source and Sink compliance testing.
-
product
Fibre Channel Simulator & Analyzer Applications Software
fcXplorer Simulyzer
Avionics Interface Technologies
FC-1, FC-2, and FC4 Analyzer modes and displays - Frame parser for custom display of FC frames and payload data - Captured data can be saved as binary or “csv” files - User-defined trigger and filter features - “Live Capture” real-time display - Error detection and reproduction - Complete control of the transmit link - Replay of recorded data with precision timing or corrected protocol timing - Special testing functions such as defining command/response for exchange management
-
product
Flow Leak Testers
If you need high-quality air flow testers, you’ve come to the right place. We carry equipment for mass flow and leak testing, laminar flow, and continuous flow. You have the option of choosing touch screen or standard digital. All our equipment is compact and includes high-performing, state-of-the-art technology. Begin testing your equipment with our premium-grade flow testing equipment. Explore our amazing selection of flow testing equipment.
-
product
Environmental Functional Test Fixtures
Circuit Check builds test fixtures for Halt/Hass testing whether a fixture is used within an environmental chamber or is a standalone fixture. Circuit Check has the capability to manufacture these types of fixtures.
-
product
Microwave Power Amplifier 1/4 Watt, 2 GHz to 50 GHz
GT-1050B
The Spanawave/Giga-tronics GT-1050B Microwave Power Amplifier offers linear high-power amplification across multioctive bandwidths. Ideal for testing in EMC, wireless communications applications, and Defense EW systems.
-
product
Personal SerDes Testers
C Series
Everything you need to develop and verify your high-speed digital algorithms is contained in these ultra-portable test instruments. They will forever change the way you think about developing and verifying Gbps digital and mixed-signal algorithms, and they will allow you to measure signals in ways that were not possible in the past. Each personalized SerDes tester is equivalent to multiple hardware platforms, containing everything that you need to make high-performance measurements like bit error rate testing, signal generation, and signal measurement.
-
product
Advanced SoC/Analog Test System
3650-EX
Chroma 3650-EX is specifically designed for high-throughput and high parallel test capabilities to provide the most cost effective solution for fabless, IDM and testing houses.
-
product
Glow Wire Apparatus
GW-4
Is designed to perform tests specified in many standards to check Resistance to Fire in Insulating parts. The best method for testing electro-technical products with regard to fire hazard is to duplicate exactly conditions occurring in practice.
-
product
PXI 8-slot BRIC Multiplexer, 8-Channel, 80-Pole (6 Sub-cards)
40-570A-114
The 40-570A-114 is a 8-channel, 80-pole High-Density Multiplexer and is part of our BRIC family. The 40-570A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
product
WaveMaster / SDA / DDA 8 Zi-B Oscilloscopes
WaveMaster / SDA / DDA 8 Zi-B Series
The WaveMaster 8 Zi-B combines the performance, signal fidelity and feature set needed for today’s high-speed measurements with the ease of use of a standard benchtop oscilloscope. Featuring the highest-speed serial data triggers, the only complete multi-lane serial data analysis and eye diagram solution, and the most comprehensive set of compliance packages, the WaveMaster 8 Zi-B simplifies the most complex testing.
-
product
AUTOMATED SAFETY AND COMPLIANCE
DMC's test and measurement system offerings include designs and development of Automated Safety, Compliance, and Benchmark Testing. These serve interests of commercial product certification, including fire hazards, safety and signaling, lighting, building safety, energy, and hazardous location testing. These also serve interests of product and technology benchmarking, including brand quality protection, consumer quality, and energy efficiency. Test systems have been developed by DMC to support many standards, including UL (Underwriters Laboratories), Consumer Reports, Intertek, Energy Star, and EN / CEN European Standards.
-
product
In House Testing
Burnsco Environmental Test Chambers
Burnsco Technologies Inc recognizes that many customers have one-time testing requirements or, from time to time, an overload of testing. With that in mind we are pleased to offer you a test center with a unique difference!
-
product
Automotive Fuse Current Probe
FUSE PEEKER
Automotive Diagnostics and Publishing
Automotive Fuse Peeker Current Probe for Testing Injectors, Coils, Solenoids and most components. The FUSE PEEKER Automotive Fuse Current Probe works with your own scope, the Auto Scope 1 or any other type of oscilloscope. It uses magnetic sensor technology, which is accurate and safe for your tool. It can detect small amounts of current as small as 5 milli-amps.
-
product
Melt Flow Index Testers
Instron® melt flow testers are specifically designed for easy and accurate measuring of Melt Flow Rate (MFR) and Melt Volume Rate (MVR). Our extrusion plastometers range from manual to semi-automated plastic melt flow index testers performing multiple weight tests. All our Melt Flow Index testing equipment meets the latest ASTM and ISO standards.
-
product
Torque Tester
TorqueLab® LTT-Series
The torque analyzer is designed for calibrating tools, joint testing, auditing and measuring torque. Torque tools go out of calibration with use. To maintain consistent accuracy, torque tools must be checked periodically for wear or defective parts. A power or hand torque tool is a measuring tool that must be properly calibrated and maintained.
-
product
Battery Testing
With the increasing dependency of back up systems on battery strings, and the escalating cost of replacing batteries, instrumentation and software systems that can measure, trend and manage the life-cycle of cells is a cost effective option.
-
product
Ultrasonic Portable Hardness Tester
MET-U1A/MET-U1A50/MET-U1A100/MET-U1A110
The PHASE II ultrasonic portable hardness testers are capable of measuring the surface hardness of a broad variety of metals on flat, round, thin or large surfaces. Unlike the standard Dynamic hardness testers, these "state-of-the-art" portable hardness testers incorporate "Ultrasonic UCI" technology, which enables the hardness testing of very thin and small workpieces, which otherwise could not be tested accurately using a portable device.
-
product
Test Automating Software Tool
SeqZap
Use SeqZap to automate your software test and save a lot of time in development projects. The primary goal for SeqZap is to enable professional, easy and pragmatic automation of system testing. System Testing Automation is both the formal test discipline of automating the execution of the system testing test cases during the software development phase of a product, but it is also the ad-hoc testing done throughout the whole product development life cycle.
-
product
Quality Of Service
Traffic is prioritized according to its importance and some types of traffic are more sensitive to latency, jitter and packet loss than other. Xena offers QoS validation solutions in accordance with RFC 2544 and Y.1564, as well as advanced statistics functions that help users track, analyze and troubleshoot QoS to maintain a high service quality guarantee. Testing that link performance complies with a Service Level Agreement (SLA) includes verifying Frame Transfer Delay (FTD), Frame Delay Variat...show more -
product
Validation, Mapping and other Services for GxP Regulated Applications
The individuality of your GxP application may require a variety of function-specific settings and measurement systems. Benefit from our know-how and let our application engineers design the optimal measuring system for you. With our consulting services in GxP, we support you from project planning (URS) to implementation and testing of your system. This ensures an optimal and efficient design.
-
product
LED Burn-In Test
Burn-in system, based on LXI instrumentation, for concurrent testing of up to 80 DUTs in a climatic chamber. Devices to be tested include modern light emitting diodes and LED modules.The system consists of 2 control cabinets, each with 40 independent supply and measurement channels. Each channel can be configured individually via the operator software (current or voltage, including the relevant limit values). The software supports logging of current and voltage values for each DUT on all 80 chan...show more -
product
100Hz-50kHz LCR Meter –
11021/11021-L
Chroma Systems Solutions, Inc.
The Chroma 11021/11021-L are the most cost-effective digital LCR Meters available, providing 100Hz, 120Hz, 1kHz, and 10kHz test frequencies for the 11021 and 1kHz, 10kHz, 40kHz, 50kHz test frequencies for the 11021-L. The standard RS232 interface, optional GPIB & Handler interfaces, high speed and stable measurement capabilities enable the Chroma 11021/11021-L for use in both component evaluation on the production line and fundamental impedance testing for bench-top applications.
-
product
Portable System for High-Voltage Solid Dielectrics Testing
HVT-70/50
Portable system HVT-70/50 is designed for carrying out high-voltage withstand testing of cable insulation and other solid dielectrics with DC (rectified) voltage up to 70 kV and AC voltage up to 50 kV RMS at industrial frequency (f = 50 Hz).
