-
product
Meter Test Benches
Test Station
The meter test station allows simultaneous testing of 3, 5, 10 or 20 induction or static electricity meters. The test station could be constructed for single-phase electricity meters or for three-phase meters.
-
product
Battery Testing
With the increasing dependency of back up systems on battery strings, and the escalating cost of replacing batteries, instrumentation and software systems that can measure, trend and manage the life-cycle of cells is a cost effective option.
-
product
NI-9222 , ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
781397-01
±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9222 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The NI‑9222 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the NI‑9222: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
product
PCI High Density Pecision Resistor Card, 6-Channel, 4Ω To 5.82MΩ
50-298-052
The 50-298-052 is a high density programmable resistor card with 6 channels which can be set between 4Ω and 5.82MΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Warm-Up Board
WECO 9000
The WECO 9000 Warm-Up Board from Radian Research provides a safe, easy to use, affordable solution to your AMI meter functional testing. The WECO 9000 originated as part of RADIAN Innovate™ Custom Design Solutions. Numerous process improvement workshops RADIAN facilitated at electric utilities have shown us that meter shops are experiencing as low as 65% pass yield on AMI meter testing. This means almost half the meters arriving are transported through the testing process and not ready for accuracy testing. Typical failures include inoperable display, diagnostic errors, disconnect switch in an open state, wrong firmware version, and inability to register on the communications network.
-
product
Torque Measurement Systems
Proper torque measurement is critical in many assembly operations. AIMCO provides expertise and measurement equipment for all three phases - before, during, and after assembly. Tool testing and capability studies can be easily performed in the tool crib or lab. Fine tuning of torque settings and process verification are achieved on the assembly line with rotary transducers. Use our complete line of electronic wrenches for final residual torque testing.
-
product
Cable Tracer and Phone Tester (2 in 1)
183 CB
Standard Electric Works Co., Ltd
Cable Tracer● Trace wires or cables.● Volume control.● Tip & Ring identification.● 2 bi-colored LEDs ( Line 1 & Line 2).● Tone speed selection : Fast & Slow.● A phone jack is designed for headset or handset. (Amplifier probe)Phone Tester● Continuity and resistance testing for voltage-free objects.● Check direct and alternating voltages.● Testing capacitors.● Testing diodes.● Power ON/OFF switch.● The indication of the LED lamp and the sound of the buzzer can occur at the same time.● The LED indication for Power ON status.
-
product
Multiple-Bus Architecture Cable/Harness Test System
CKT1175-MBA
The CKT1175-MBA (for multiple-bus architecture) will provide seamless testing of electronic racks, panels and chassis containing passive and active components such as relays, solenoids, switches, circuit breakers, lamps and LED's, diodes, resistors, capacitors, etc. This functionality is made possible by a switching matrix that is up to 10 levels deep, plus a multiplexer that controls the various stimuli sources, instrumentation connections, and external energization outputs.
-
product
DC High Voltage Test Set
It is extensively used in electrical and power generation industry for varied testing operations.
-
product
PXI 3A Power MUX BRIC, 16-Channel, 12-Pole
40-571-304
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
Secondary Current Injection Test Sets
Our range of units covers applications up to 200A and includes single phase and three phase units with applications for testing and timing of IDMT relays, thermal overloads, MCB’s and auto-reclosers.
-
product
Non-Destructive Testing Equipment
BOLT-Tester
BTS(BOLT-Tester) is developed in 2012 after the collapse at SASAGO Tunnel on the Chuo Expressway in Japan. Visual inspection and hammer sound testing are main inspection methods for maintenance and management of anchor bolts in a tunnel. However, these methods have some issues in regard to objectivity and reliability of the results. Pull out testing is also one of a testing method for the soundness test of anchor bolts, however, this method have also some issues in regard to cost and time, and t...show more -
product
Single Screw Electromechanical Universal Testing Machine
CMT Series
Jinan Testing Equipment IE Corporation
The CMT series single screw testing machine is designed for mechanical property test mainly on metal materials, cement, asphalt, and bitumen etc. A variety of fixtures can be offered to do compression, bending and shearing test as well. This series of single screw testing machine is suitable for the applications in quality inspection, research, metallurgy, rubber & plastics, and knitting materials, and widely used in many fields such as industry factories, mineral enterprise and high schools.
-
product
AC Hipots for Apparatus Testing
PFT Series
PFT Series test sets are portable, ideal for testing substation apparatus. These are among the smallest, lightest, and most economical AC hipots available. Standard models are available from 10 kV AC – 100 kV AC and rated 1 kVA – 3 kVA.
-
product
Commutator Testing Unit
SCR ELEKTRONIKS have designed “Commutator Testing Setup” to provide Commutator manufacturers and users a simple and speedy method for testing their Commutators. This single station commutator testing set up therefore user can test one commutator at a time. In Automatic mode of testing this set up performs two tests automatically.
-
product
PXI/PXIe MIL-STD-1553 Multiplexer, Single 16-Channel, 2-Pole
42-739-001
The modules are ideal for the testing of multiple devices that use a serial communication interface, allowing the test system to select one target device from many. The design is bi-directional to permit use as a multiplexer or de-multiplexer with no impact on performance. The module uses long lifetime electromechanical relays characterized for use in communications systems.
-
product
Logic Analyzer Probe
FS2521
The FS2521 is a logic analyzer probe used to test DDR4 SO-DIMM memory. When used with the triggering and analysis capabilities of Keysight’s U4164A logic analyzer modules, it gives the user an extremely effective tool for debugging, testing and verifying DDR4 SO-DIMMs. Now qualified at 3200MT/s
-
product
2-port Battery Portable Passive Intermodulation Analyzer - iXA Series
iXA
The Kaelus iXA Series Passive Intermodulation (PIM) analyzer is a dual-port, battery powered PIM Test Analyzer. It supports multiple test scenarios such as testing at the top of the tower, the base of the tower, rooftop, in-building for DAS systems and external PIM Finding.No other PIM tester has ever been integrated to this level! The iXA includes a network of electronic switches to change from one-port to two-port measurement seamlessly. In addition, with integrated Range-to-Fault (RTF) on eac...show more -
product
Multiple-Input Multiple-Output (MIMO) Sine Test
EDM Modal Sine Testing includes a dedicated test setup and operation process flow using a single or multiple modal shakers outputting a sine wave to acquire FRF signals. The Source Output type is either Swept sine or Stepped sine. The sweep mode can be linear or logarithmic. The FRF signals of each measurement DOFs with respect to defined reference DOF will be constructed. The output drive level can be defined to run the test under no control strategy, or the response of a control channel can be specified to run the test in a closed loop.
-
product
Three-Phase Transformer Winding Resistance Meters
TWA Standard Series
When it comes to winding resistance measurement on three-phase power transformers and autotransformers, TWA Standard series offers some of the most technically advanced instruments with LCD display in the market. Both models are capable of testing six transformer windings with a one-time cable connection, as well as three-phase automatic transformer demagnetization. The stored magnetic energy is safely automatically discharged at the end of the test. The built-in tap changer control unit enables...show more -
product
In-Circuit Test Fixture Design Services
XJTAG offers consultancy services to design and build production test fixtures that integrate JTAG boundary scan with bed-of-nails testing.
-
product
Multi-Function Tester with Modular OTP Design for Chemical Analytics
Multi-function-tester, based on the LXinstruments OTP2 system platform. The system is utilized for assembly and final testing as well as calibrating measurement devices for chemical analytics in a high mix / medium volume environment.
-
product
LB-Series Digital AC Load Banks
The LB-Series AC Load Banks are designed for high power portable load testing of generators, UPS, and other critical AC power sources. Available models meet a range of voltages including but not limited to 208, 380, 440, and 480 VAC. Load power model options reach 1000 kW standard with other options available.
-
product
CMK Mechanical Kits
Columbia has created a unique mechanical click system using ball bearings and guiding sleeves. The UUT is connected to the spring contact pins that are connected to the testing environment in a completely linear fashion. Connecting the UUT to probes can be approached both from the top and the bottom and, optionally, even from the side. The ergonomic housing provides generous space for additional measuring electronics. The back and bottom of the housing can be adapted to the various test system interfaces.
-
product
Hi-Pot Testing
The CableEye HVX System combines our M3U tester with a high voltage module to provide Hi-Pot testing of insulation resistance and dielectric breakdown up to 1500Vdc and 1000Vac.
-
product
Test Compliance
AMETEK Programmable Power, Inc.
A growing number of electronic products manufactured today have to meet international regulatory requirements for emissions and immunity. This is particularly true for products sold in the European community as well as a growing list of countries in the Far East. AMETEK Programmable Power compliance testing solutions measure products for the latest standards.
-
product
150~300W DC Electronic Loads
JT631 Series
Nanjing Jartul Electronic Co., Ltd
JT631 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT631 series load very suitable for testing power supply when produced in large quantity. Besides, JT631 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT6...show more -
product
10 GHz Signal Source
YIG Series
The SC5503B and SC5502A are designed to meet demanding low phase noise applications. This is accomplished by employing a multiple phase-locked loop architecture as well as a YIG oscillator as the heart of its synthesizer. Frequency accuracy is provided by an onboard 10 MHz temperature compensated crystal oscillator (TCXO) which can be phase locked to an external reference source if required. These modules can be used as standalone CW signal sources or as LO sources for frequency conversion syste...show more -
product
Testing Solutions
FEV has been globally recognized for its flexibility and innovative ideas. In the Testing Solutions division, FEV continues this tradition, providing its customers with intelligent and innovative test cell solutions that meet their needs. From the earliest stages in the development of a project, FEV uses its experience gained from the operation of more than 150 test cells to ensure that newly planned facilities / installations are cost effective, modular and provide high utilization.
-
product
Audio Cable Testers
AudioJog Pro 3
Audio cable tester with SINGLE & DOUBLE ended testing, memory and intermittent fault detection .
