Power Calibration
Verify power measuring instruments accuracy.
See Also: Calibration, Calibrators, Display Calibration, Calibration Standards, Calibration Software, Calibration Services, Calibration References
-
product
Sound Level Calibrator
511E
Accepted internationally 1 kHz represents the "0 dB" reference point of A, B, C Weighting and other filters utilized in acoustic measurement. The Pistonphone - a mechanical sound source - offers a slightly higher degree of accuracy at a substantial increase in cost. In addition, the 200 or 250 Hz operating frequency is mechanically limited and not suited for measurements of filtered inputs. The 0.2 dB accuracy is quickly lost in the 0.7 to 1.5 dB tolerances acceptable for weighting filters at frequencies around 250 Hz.
-
-
product
Power Supplies
CU - SERIES
The CU-series is a semi-modular power supply that lets you select the cables you need while powering your system at a healthy voltage. Everyone likes a clean and easy installation. This power supply allows you to keep what you want and remove what you don't. While necessary connectors, like the 20+4 pin power connector, are attached to the unit, you decide which of the others should stay. Customize your power supply to reflect your system.
-
product
High Power Digital Lab Series Regulated DC Power Supply – 2KW
- 2000W different combination- High current density.- 19″ rack adaptable -3U high- Front panel potentiometer to set V&I- Remote sensing- 3Digit seven segment display for V&I- High stability and close regulation- Phase controlled preregulation plus linear post regulation- Optional, at extra cost- Over voltage protection- 19″ rack mounting- Analogue programming and monitoring for V&I
-
product
Universal AC-DC Power Supplies
PS-RS35-24-0
The PS-RS35-24 is a small, convection cooled 35W power supply for embedded systems. It is a universal design that accepts 88 to 264VAC input and generates up to 1.5A of current at 24 volts. The 24 voltage output can be adjusted with an on board trimpot. The PS-RS35-24 is small, measuring only 99 x 82 x 36mm.
-
product
Modular DC Power Supply
62000B
Chroma Systems Solutions, Inc.
Chroma’s 62000B series of Modular DC Power Supplies offer 5 types of power module with ranging from 1V to 150V, current from 10A to 90A, and offers two mainframe type of six and three position. The six position mainframe can envelop in up to six power modules paralleled operation for 9KW power output. The 62000B can easily parallel up to 14 mainframes to 120KW with current sharing and CAN bus control for bulk power applications.
-
product
Wind Power Solution
EVO ACCIONA
The EVO ACCIONA is custom-made with firmware and fixtures designed specifically for Acciona turbines. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
product
PICMG® 2.11 47-Pin Hot-Swap Redundant 3U CompactPCI® 8HP 250 W Power Module
cPS-H325/48
- PICMG® 2.11 CompactPCI® Power Interface compliant- 3U CompactPCI® 8HP form factor- PICMG® 2.11 47-pin CompactPCI® in-rack power module interface- 250 W DC output- Active PFC (Power Factor Correction) meets IEC1000-
-
product
Power Bead Inductors
Power bead inductors are typically used in high current multi-phase voltage regulators that power processors, memory modules and high current ASICs and FPGA in a wide range of applications including servers, graphics cards, storage and data centers. The construction consists of a ferrite core assembled over a 1T or 2T winding and which allows for extremely low DCR, high peak current and low AC losses. Pulse has single phase, integrated phases and coupled inductor versions. Our high volume manufacturing enables us to produce components that are cost-effective while maintain exceptional quality and reliability.
-
product
Standard RF Power Sensors
Coaxial Dynamics "Standard" line of RF Power Sensors provide DC currents proportional to the forward and reflected power flowing through the line. All models are designed to drive a 30A, 1400-Ohm meter, or provide approximately 100 millivolts across a 5K load.
-
product
Calibration Management Software
MET/CONNECT™
Calibration Management Software through Fluke Calibration MET/CONNECT™ Qualer is a premier asset, maintenance and calibration management system providing a pre-configured, business-in-a-box, best in class, software solution for progressive companies. Fluke Calibration’s MET/CAL® is the leading calibration automation software platform, allowing calibration labs to harness the power of thousands of automated procedures. Qualer and MET/CAL® can now be connected through Fluke Calibration's MET/CONNECT™ integration app. This enables labs to leverage the power of MET/CAL® procedures and provide the results seamlessly to Qualer as their system of record. Qualer's partnership with Fluke Calibration and MET/CONNECT™ provides a seamless way to integrate the two platforms and bring the benefits of automated calibration into the Qualer platform.
-
product
Power Supplies
CUL-650B
The CUL-series is a semi-modular power supply that lets you select the cables you need while powering your gaming system with a 140mm Blue LED cooling fan and 6 pin PCI-E ready. **850W & 950W is offering 140mm Blue LED cooling fan & Dual 6+2 PCI-E ready. Everyone likes a clean and easy installation. This power supply allows you to keep what you want and remove what you don't. While necessary connectors, like the 20+4 pin power & 4+4 pin CPU connector are attached to the unit, you decide which of the others should stay. Customize your power supply to reflect your system.
-
product
Plastic Optical Power Meter
POFPM100
Shanghai Tarluz Telecom Tech Co., LTD
POFPM100 POF OPM used for the plastic optical fiber within 600 ~ 1000nm wavelength range, w, dBm units, five calibration wavelengths.
-
product
Power Supplies
A power supply is an electrical device that supplies electric power to an electrical load. The main purpose of a power supply is to convert electric current from a source to the correct voltage, current, and frequency to power the load.
-
product
Power Distributions
LXinstruments Power Distribution Units (PDU) provide all of the functionality required to power a test system in a compact 19-inch rack. This means that devices can be supplied with both mains voltage and DC voltage. With the soft-on-off function, the PDU can be controlled remotely via remote buttons and other potential-free contacts. We carry single-phase devices for the 16 A connection to three-phase devices for the 3x63 A or for the 125 A connection.
-
product
Brick Power Module Test
Modern servers, workstations, and telecom equipment often use an Intermediate Bus Architecture (IBA) powered by isolated DC/DC converters known as "brick" modules. These brick converters step down the input voltage to a lower DC bus voltage, enabling designers to implement efficient, high-density, non-isolated Point-of-Load (POL) regulators that power components such as microprocessors, FPGAs, and ASICs on system boards. With smaller voltage step-down ratios now common, designing POL regulators has become more straightforward. Brick modules are so named for their standard physical formats (1/4 Brick, 1/2 Brick, Full Brick, etc.), making them easy to integrate and replace.
-
product
Power Supply Support
Renesas offers a complete portfolio of system supervisory solutions ranging from single to quintuple (five) voltage monitors. In addition, the system management ICs are voltage monitors with small amounts of I2C or SPI software programmable EEPROM memory. Renesas single-chip sequencing solutions sequence up to four different voltages while providing other useful features such as voltage monitoring, fault protection, and reset assertion.
-
product
DC Regulated Power Supplies
PGP Electronics Private Limited
PGP Electronics Regulated Power Supplies are robustically designed to withstand rugged operation. PGP Electronics manufactures both the Standard and Custom-built power supplies. Manufacuring of custom-built power supples is our speciality.
-
product
Uninterruptible Power Systems
SP Series
Clary's SP Series are the world's most advanced Uninterruptible Power Systems (UPS), designed specifically for electronics equipment in IT, Traffic and Security applications. Industry proven, each product in the SP Series delivers on-line double-conversion protection 100% of the time for reliable, continuous, and error-free operation regardless of utility power quality.
-
product
Pressure Calibrators
We offer pressure calibrators as portable and as workshop models. Pressure measurement is performed with internal and/or external pressure modules for better flexibility. Pressure measurement ranges go from vacuum up to 1000 bar (14,500 Psi). Both gauge (vacuum and positive) and absolute pressure can be measured with same modules meaning you don’t need to buy so many module for greater flexibility. Also, intrinsically safe pressure calibrators are available for use in hazardous areas.
-
product
Metra Power Clamp
400A
Metra Power Clamp 1000A/400A measures, calculate and displays important electrical pa-rameters of single phase or three phase power system. It also features Resistance, continuity, diode and non contact voltage detection.
-
product
Power Interface Module
SP 1250LX
The SP 1250LX products feature an integrated Power Interface Module (PIM) and programmable display. The LX Series are advanced Uninterruptible Power Systems (UPS) that provide clean, regulated Dual Conversion power for controllers and other sensitive equipment inside the cabinet.
-
product
Switch-Mode Isolated Power Supply
Renesas offers a wide selection of PWM controllers designed for switch-mode DC/DC and AC/DC power supplies requiring an isolation transformer, such as off-line AC/DC and -48V telecom-input DC/DC converters.
-
product
Power Device Test Systems
Power semiconductors are devices that control electric power, and are used in automobiles and a wide range of electrical products. Our power semiconductor test systems, developed and provided by CREA, an Advantest Group company, specialize in testing power semiconductors that handle high voltages and large currents, and have special safety features for this purpose.
-
product
Digital Load Calibrator
HS 2000
Jinan Testing Equipment IE Corporation
The load cell calibrator is used to calibrate the load of testing machine and hardness tester, and also can be used for force measuring. It is digital display type with high accuracy of less than +0.3%, and easy to operate
-
product
PD Calibrator
PDCAL has excellent pulse-with stability; scale calibration factors are permanently stored inside its flash memory. Thanks to on board photo coupler PDCAL output pulse can be synchronized with the actual line frequency through external surrounding electrical light source systems.
-
product
Portable AC/DC Power Supply
UPS S3
The Vanguard UPS S3 is an AC/DC adjustable output power supply designed to operate substation circuit breakers. The UPS S3’s AC and DC voltage sources can supply up to 10 Amperes during the circuit breaker coil energization and circuit breaker charging motor operation. Powered by a single phase 90-120 Vac voltage source, the UPS S3 provides an isolated adjustable AC/DC voltage source. Output voltages are variable via the front panel control knob.
-
product
Automated CMM Calibrated for High-Production Shop Floor Inspection
CMM Master
The CMM Master provides process control by delivering optimal price and performance to your application. The system brings highly repeatable, thermally insensitive, versatile, and programmable inspection to the shop floor.
-
product
Power Supply Equipment
It is a stabilized power supply such as constant current, constant illuminance, etc. to light the xenon lamp stably.
-
product
DC Power Supply
WPS Series
The WPS Series programmable DC power supply is a high-precision, wide range of voltage & current within the power rating of the power supply, full-featured high power density programmable DC Power Supplies. It can provide wide-range, low-ripple and stable DC output which is used for DC input products and components function testing and experimental simulation.
