Tunable Laser Sources
See Also: Tunable Lasers, Laser Sources
-
Product
AC Power Source
LSP-500VAR
-
• AC-DC-AC frequency conversion technology, Controlled & tested by 16 bits MCU • Protection for over hot, thundering voltage and current • Total voltage distortion: ≤0.3%; Voltage stability: ≤0.05%/30min • Load adjust rate: ≤0.05%; Frequency stability: ≤0.01%/30min • Output voltage range: AC 0.0~300.0V, Output Frequency Range: 45~70Hz, 100Hz, 200Hz and 400Hz • It is pure sine wave AC power source with low harmonic and high accuracy • Input Power: 220V and 50/60Hz (110V can be option) • Communicate with PC via software, the Voltage & Current set by the software and Power Output can be remote controlled.
-
Product
Picosecond Lasers
-
High single pulse energy: over 100 μJ@100kHzTotal pulse controlBurst modeVariable rep rate: single shot to 2MHzOption to 8MHzPEC: power or pulse energy controlPulse width <15ps, optional 20-100psZero leakageExcellent beam quality (M²<1.3)Exceptional beam pointing stabilityCompact industrial grade ps laserLow maintenance
-
Product
Controllable, Programmable DC Source
LAB SMP
-
*Easiest operation via the front panel*Indication via graphic display*Constant current, voltage, resistance, power operation and simulation of PV characteristics*Creation of any voltage and current curves via memory card or digital interface (sequential control)*Voltage and current rise time (U and I slope) adjustable*Umax and Imax can be set by the user in order to limit the output voltage or current
-
Product
MP field sources calibration set
-
The MP field source calibration set is used to measure electric or magnetic fields in a frequency range up to 3 GHz. RF fields or transient fields can be measured. The MP field source calibration set is used to check fields of the Langer EMV-Technik GmbH field sources, fields of TEM cells and IC striplines.
-
Product
CO2 Laser Spectrum Analyzer
-
The spectrum analysis screen has a response time of 1/4 seconds and permits the instrument to resolve all the CO2 rotational lines. The Model 16-A is light, portable and can easily be introduced into laboratory setups.
-
Product
Broadband Mid-Infrared Femtosecond Laser Source
FemtoFiber dichro midIR
-
The new FemtoFiber dichro midIR represents an ideal laser source for mid-infrared spectroscopy and imaging. It provides a tunable broadband output in the wavelength range of 5 to 15 m (20 - 60 THz, 670 - 2000 cm-1). The unique 400 cm-1 broad emission spectra allow to excite a wide range of materials at the same time. The air-cooled system is based on TOPTICAs proprietary fiber laser technologies and includes a difference frequency generation (DFG) unit as well as all necessary electronics into the same box. All functions and features are computer controllable by Ethernet or USB interfaces.
-
Product
Voltage Integrated Sources
VIS
-
The VIS voltage integrated source was designed to be used as a stable alternating voltage source for electricity meter test equipment, and in laboratories. The output voltage is isolated and independent of mains voltage. VIS is available in a variety of configurations depending on the values of output power and output voltage.
-
Product
Picosecond Lasers
PL2250 Series
-
Featuring up to 100 mJ pulse energy and less than 30 ps (20 ps optional) pulse duration, PL2250 series picosecond mode-locked Nd:YAG lasers set new standard in high pulse energy picosecond lasers. Innovative and cost effective design allows to improve laser reliability, while reducing running and maintenance costs.
-
Product
Laser Power / Energy Meter
StarBright 7Z01580
-
*Compatible with all standard Ophir thermal, BeamTrack, pyroelectric (PE-C series) and photodiode sensors*Brilliant color large size TFT 320x240 display*Choose between Digital with Bargraph, Analog Needle, Line Plot (for laser tuning), Pulse Chart, Pass/Fail, *Position, Stability, Real Time Statistics displays*Sophisticated power and energy logging, including logging every point at up to 5000Hz with Pyro sensors*Math functions for advanced processing such as Density, Scale Factor, Normalize against base line, etc.*Can mix functions together and display the results graphically. Function results can also be logged.*USB Disk on Key (Thumb Drive) for nearly unlimited data storage.*USB and RS232 interfaces with StarLab PC applications and User Commands document
-
Product
Laser Diode Characterization Systems
-
Artifex Engineering GmbH & Co. KG
The LIV100 and LIV120 employ digitally programmable analogue end stages for flexible and accurate current control. A wide range of current end stages are available with maximum currents of 250mA for low power and telecom lasers or up to 1200A for high power laser bars. Custom units are available with even more current!
-
Product
Power Profiler, DC Energy Analyzer, Power Supply, Digital Multimeter, Source Measure Unit, Power Debugger
Otii Arc Pro
-
Otii Arc Pro is an instrument that can precisely source voltage or current and simultaneously measure voltage and/or current. It computes power and energy and syncs with software output, enabling engineers and developers to easily see what drains the energy and optimize the battery life of their devices under test.
-
Product
Industrial Short-Pulse Lasers
-
Short-pulsed industrial lasers from nanosecond lasers with up to 1 Joule pulse energy, through picosecond lasers with up to 80 MHz repetition rates, to femtosecond lasers with up to 900 fs pulse widths.
-
Product
Laser Rangefinders
-
A rangefinder that uses a laser beam to determine the distance to an object.
-
Product
Laser Diodes
-
Our laser diode portfolio is broad, extending from cw laser diodes to pulsed laser diodes to high-power laser diodes. For special areas of application VCSELs and quantum cascade lasers are also included in our range of products.
-
Product
Power Source
-
Beijing GFUVE Electronics Co.,Ltd.
A power source is any type of electrical or mechanical device that is capable of delivering an electrical load and/or a back-up power supply.
-
Product
32-CH Sourcing Type Digital Input EtherCAT Module
EPS-1032
-
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
Product
Calibration Light Source
CAL2
-
Image Engineering GmbH & Co. KG
The CAL2, based on our 22 channel spectrally tunable iQ-LED source, can be adapted for use in many different areas.
-
Product
Point Source
JF Series
-
The JF Series contains EAW’s high-output, two-way systems intended for mobile production or permanent installation.
-
Product
Fiber Coupler Diode Laser
CAWS-XX
-
* High Power，High Efficiency* Coupling efficiency ≥80%* Standard fiber connector type* Lifetime > 10000h
-
Product
Programmable AC Power Source
LSP-500VAC
-
• Applied with the AC-DC-AC inverter technology and digital waveform synthesis & waveform feedback technology, low distortion power; • Applied with entire cycle high-precision measurement technology and high-speed sampling technologies, panel of instrument will directly and accurately displays the power output of the voltage, frequency, current, active power and power factor to achieve the integration of the source table; • Applied with SCM control and measurement technology, high intelligence; • Applied with zero output impedance technology, the output equivalent impedance is almost zero and further improve the stability of power supply; • Applied with isolated floating output technology, the power output and input have good isolation, floating output, conducive to make sure power itself safety and operator’s safety; • Perfect voltage, current anomalies and overheating protection, improve the reliability of power supply; • Applied with power limiting technology to avoid strong interference on the power grid and other electrical equipment, while facilitating reliable operation of the power supply itself; • The input voltage can be option via a toggle switch of panel mains 110V/220V; • The initial phase and end phase of the output voltage waveform can be set {0°-359° (±1°)}; • Measurement process can be programmed to control (1 to 50 memory groups, 1 to 9 steps for each memory group);
-
Product
Open Source Implementation fo the Open Management Group (OMG) Data Distribution Service (DDS)
Cyclone DDS
-
Cyclone DDS is the new fastest growing Open Source implementation of the Open Management Group (OMG) Data Distribution Service standard (DDS). Today, Cyclone DDS is gaining momentum in the Robotics, the Autonomous vehicles and the Automotive markets as well as in other mission critical and demanding IoT systems where:- Performance,- Robustness,- Safety ,- Security,- Interoperability, and- Opennessare fundamental for the success of these systems.
-
Product
Laser Source
TW3110
-
Techwin(China) Industry Co., Ltd
Laser Source TW3110 is the most rugged small size instrument in the industry. It integrates super small size and strong function in one unit. With 3 pieces of 1.5V alkaline batteries, it can work continuously for more than 40 hours. The total weight is only 110g. Together with the TW3205 Mini optical power meter, it provides an excellent solution for fiber optic network and for field work.
-
Product
Laser Head
5517FL
-
The Keysight 5517FL is used primarily in VME and PC based laser interferometer systems where the velocity of motion is faster, such as semiconductor lithography and flat panel applications. Please contact Keysight for custom requirements.
-
Product
Precision Laser Distance Meter with Clinometer
TRUPULSE 200X
-
F. W. Breithaupt & Sohn GmbH & Co.KG
*Scope magnification 7-times*Field of view 100m/915m distance*LED Display*Range to non-reflecting targets 1.900m*Range to reflecting targets 2.500m*Accuracy in range ± 4cm (± 30cm to weak targets; shown in display)*Accuracy in slope ± 0,1°*RS 232/Serial interface and bluetooth (iOS compatible)*IP protection IP56
-
Product
Laser Distance Sensors (Time-of-Flight)
optoNCDT
-
Laser distance sensors are designed for non-contact distance measurements: laser gauges for measuring ranges up to 10m, laser distance sensors for up to 3,000m. These sensors are used for positioning and type classification in machine building and handling equipment.
-
Product
Compact Deuterium, Tungsten Halogen or Glow Bar Light Source
LSH Illuminator
-
Compact lamp housing for a variety of types of light sources from the UV to the IR including deuterium, tungsten halogen and glow barApplications for compact arc lamp housings cover a broad range of scientific, OEM and research applications. Arc lamp illuminators are used for a broad range of applications almost as diverse as the wavelength range across which they emit.
-
Product
Programmable AC and DC Power Source
AFX Series
-
The AFX Series is a family of high power, single, split and three phase, AC, DC and AC+DC output capable Power Sources. Available models range from 6 kVA to 90 kVA with available configurations to 150kVA. Using a modern user interface for ease of use, the AFX Series is cost effective and fully programmable for both basic frequency conversion and advanced AC power line or DC power disturbance test applications.
-
Product
Laser Scanning Oil Film Detector
LO-300
-
LO-300 provides early warning by on-line detection of oil leakage with a laser and a security camera (option)LO-300 uses a laser to scan water surface or the ground to detect an oil film with high sensitivity.LO-300 with camera unit (option) enables to record the video when LO-300 detects the alarm and stores the image captured before and after alarm signal.
-
Product
AC Power Sources
-
AMETEK Programmable Power, Inc.
AMETEK Programmable Power's AC power sources range from 800VA to 480kVA. From compliance test systems to rack-mounted industrial power subsystems, AMETEK Programmable Power is the leader in the design and manufacture of precision, programmable AC power sources used in R&D, test and measurement, avionics testing, inverter testing, arbitrary waveform generation, bulk power and power conditioning applications across a wide variety of industrial segments.
-
Product
Spectroscopy Lamps and Light Sources
-
The StellarNet portable Light Sources facilitate measurements in the UV, VIS, and NIR for various samples and application types using standard SMA-905 optical connectors. These low cost modular components are robust, reliable, and designed to last in portable and industrial environments.
