IR Sensor
Detect infrared radiation and produce a measurable signal of the detected amount.
-
product
Power Sensor and SNS Noise Source Cables (3 m/10 feet)
11730B
The Keysight 11730 series power sensor cables are used with the 8480 and E-series power sensors (except the E9320 family of peak and average sensors). These cables are designed to reduce RFI effects on low power readings with an improved shielding design in the cable itself. Cables may be ordered individually or in pairs in any combination desired for single and dual-channel measurements.
-
product
E-Series Average Power Sensor
E9300A
The E9300A diode power sensor measures average power over the frequency range 10 MHz to 18 GHz and power range -60 to +20 dBm (80 dB dynamic range).
-
product
10 MHz To 6 GHz LAN Wide Dynamic Range Average Power Sensor
L2051XA
Frequency range of 10 MHz – 6 GHzLAN connectivity with a wide dynamic range of -70 to +26 dBm for small signal measurementsFast real-time measurement of 50,000 readings/secReal-time measurement with zero dead time to ensure every single continuous pulse is measuredAverage mode time-selectivity function allows full dynamic range for average and time selectivity average power measurementsInternal zero and automatic calibration saves time and reduces measurement uncertaintyA BenchVue software license (BV0007B) is now included with your instrument. BenchVue makes it simple to connect, control instruments, and automate test sequences
-
product
10 MHz to 50/53 GHz USB Wide Dynamic Range Peak and Average Power Sensor
U2065XA
The Keysight U2065XA is a fast, accurate and wide dynamic range 10 MHz – 50/53 GHz USB peak and average power sensor.
-
product
Diode Power Sensor
8481D
The 8481D diode power sensor measures average power over the frequency range 10 MHz to 18 GHz and power range -70 to -20 dBm (50 dB dynamic range).
-
product
Thermocouple Power Sensors
N8486AQ
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
product
10 MHz to 50/53 GHz LAN Wide Dynamic Range Peak and Average Power Sensor
L2065XA
The Keysight L2065XA is a fast, accurate and wide dynamic range 10 MHz – 50/53 GHz LAN peak and average power sensor.
-
-
product
Low Side, 200 MHz, 100 PA – 20 MA
CX1103A
The CX1103A low side current sensor is a dedicated accessory for the CX3300 series mainframe and features the series widest stand-alone bandwidth up to 200 MHz
-
product
S2 Spectra Sensors
ULP-S2 WBI/V
The ULP S2 Spectra Sensor tests for LED intensity, and for any color in the visual spectrum, plus white. The S2 Spectra Sensor is well-suited for the test of “boundary” color LEDs, as it can unambiguously and repeatedly distinguish between not only adjacent visual colors such as green and yellow, but it can determine different hues of the same color such as yellow and amber, regardless of LED intensity. Implemented in a unique and customizable 2-Part solution, the S2 Spectra Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsOutput Pins: 4 gold-plated standard wire-wrap pins (0.025 in. sq.)Output Loads: ‘Int.’& ‘Color’- 2Kohms min., 100pF max.Sensor Size: 0.560 in. dia x 1.38 in. long.Typical response time: Typical response time: <10mS capture time; <100mS overall response timefor color and intensity simultaneouslyFiber-Optic Probes: Can be paired with any Universal LightProbe Fiber-Optic Probe
-
product
IR Thermometers
This device truly stands out because of its fast response, high/low alarms and dual laser pointer. It is used by maintenance professionals to quickly locate worn machinery, hot spots in electrical panels and defective HVAC equipment.
-
product
IR Inspection System
EVG®20
The EVG 20 offers a fast inspection method, especially for fusion bonded wafers. A live imageof the entire wafer via IR transmission supports void detection down to a radius of 0.5 mm. The infrared inspection system is a perfect match for fusion bonding processes either as the stand-alone EVG 20 tool or as a station in EVG''s integrated bonding systems.
-
product
ATEX-Compliant IR Temperature Sensors
FLIR A310 ex
Explosive atmospheres need to be protected from ignition sources. Selecting equipment and protective systems which meet the requirements of the ATEX Product Regulations or similar regulations is essential. FLIR A310 ex is an ATEX compliant solution, with a thermal imaging camera mounted in an enclosure, making it possible to monitor critical and other valuable assets also in explosive atmospheres. Typical applications for the A310 ex include process monitoring, quality control, and fire detection in explosive locations. Because the FLIR A310 ex is rated IP 67, it can be installed in dusty environments. The Flame-Proof Enclosure "d"prevents any explosion transmission from the inside of the enclosure to the outside.
-
product
Thermal Power Sensors
NRPxxT/TN/TWG
The R&S®NRP power meter sensors have long been recognized for delivering supreme precision and speed. The R&S®NRPxxT, R&S®NRPxxTN and R&S®NRPxxTWG thermal power sensors are especially used for complex measurement tasks where highest accuracy counts
-
product
E-Series Peak and Average Power Sensor, 50 MHz to 6 GHz
E9322A
The E9322A power sensor has a 1.5 MHz video bandwidth and is ideal for time-gated peak, average and peak-to-average ratio power measurements on TDMA and CDMA wireless formats such as Bluetooth.
-
product
10 MHz - 18 GHz USB Power Sensor
U2000A
U2000-series USB Average Power Sensor enable fast, simple setup by providing plug-and-play USB connectivity and by eliminating the need for a separate power meter.
-
product
Pocket IR Dosimeter
Shenzhen Chuangxin Instruments Co., Ltd.
This Pocket IR Dosimeter is a handheld radiometer with the characters of high-precision, pocket, stable property and easy to use
-
product
S2 Ultra High Sensitivity Sensors
ULP-S2 UHS
Universal LightProbe S2 Ultra-High Sensitivity Sensors are designed for the test of very dim LEDs, as low as 0.01 mcd minimum, and including very low light-level LED-illuminated action-indicator switches, controls and status indicators for night/dark viewing in automobile interiors. Recommend the use of wide-aperture stainless- steel encased Fiber- optic Probes with contacting tips.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. long.Typical response times: <190mSFiber-Optic Probes: Wide-Aperture Fiber-Optic Probe recommendedDesigned for the test of very dim LEDs, as low as 0.01 mcd minimum
-
product
S2 Spectra USB Sensors
ULP S2 SPECTRA USB
Universal LightProbe S2 Spectra USB Sensors test a wide range of LED intensities and any color in the visual spectrum, plus white, providing a linear response with a serial digital output via a PC. A standard USB Cable is provided to connect to a mini-type B five-pin USB connector, which is integrated into the S2 Spectra USB Sensor.Operating temperature range: 0oC to 70oCOutput Port: A standard mini-type B five-pin USB connector is integrated into the S2 Spectra USB Sensor,and a standard USB Cable is provided to connect to a USB portSensor Size: 0.560 in. dia x 1.38 in. long.Typical response time: < 10mS for color and intensity as a serial bit- stream (19200 baud rate)Fiber-Optic Probes: Can be paired with any of a wide range Universal LightProbe Fiber-Optic Probes
-
product
IR Carbon and Sulphur Analyzer
LD-LCSA-A11
IR Carbon and Sulphur Analyzer LCSA–A11 is a unit for determination of sulphur and carbon equipped with two treatment units including a high frequency induction burner and flexible temperature settings with automatic control. With an analysis time of 25 to 60 seconds and oxygen purity of 99.5 %, the multi-shielded isolation circuit prevents the machine for high frequency interference. High speed 24-bit sampling improves sensitivity and accuracy.
-
product
IR Thermometers
UEi Test & Measurement Instruments
Non-contact IR energy measurement to determine temperature.
-
product
IR Digital Laser Thermometer
214L
With a user switchable measuring range of -35°C to 365°C or -31°F to 689°F, a digital display of the temperature is produced in less than one second.Non-contact technology with laser spot indicatorºC / ºF user switchableFast, 1 second scanning of any surfaceMeasure objects as small as 25mm (1”)Distance-to-Target Ratio of 8:1Easy to read LCD display
-
product
Waveguide Power Sensor
Q8486D
Excellent SWR for reducing mismatch uncertainty50 MHz calibration port Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter Accurate average power measurements over -70 to -20 dBm Frequency range 33 GHz to 50 GHz Diode power sensing element
-
product
Near IR Image Plates
The IR Display Plate is a versatile instrument that presents clear, high contrast images of all near IR laser beams. These displays are made on infrared sensitive phosphors which offer a variety of unique features, variable image retention times for pulsed lasers, high resolution for CW YAG, and a good response to gallium arsenide light-emitting diodes. All near IR lasers are capable of being displayed over a wide sensitivity range.
-
product
C/I Non-Contact IR
Dual Laser Infrared Thermometer
*Both TG-1000 and TG-2000 offer:*Safe, non-contact temperature measurement.*Laser spot indicator shows approximate center of target measurement area.*Display temperatures in either Fahrenheit or Celsius.*Adjustable emissivity for optimum temperature reading accuracy on a wide range of materials and surfaces.*Min, Max, Difference and Average temperature functions.*Backlight display for easy readings in any environment.*Auto power off for longer battery life.
-
product
IR CAMERAS
IRC800
Sierra Olympia Technologies Inc.
The IRC800 Series cameras offer the ultimate in flexibility for research scientists. Camera operators can vary integration times, frame rates and cold filters to meet the most precise testing requirements making the IRC800 the perfect instrument for prototyping system development or where application requirements may change. A 1/3-liter LN2 pour-filled Dewar assembly maintains temperature for up to 20 hours unpowered and 9 hours powered which makes the IRC800 Series perfect for Scientific Imaging, Process Analysis and Quality Assurance. A developer’s kit is available for users who wish to create their own applications.
-
product
IR Thermometer w/ Twin Lasers
EST-67
*Twin Laser Pointers for Precise Accuracy & Aiming *Lasers converge at optimal measuring distance *Temp Range: -58 to 1022F / -50 to 550C *12 to 1 Distance to Spot Ratio *Continuous Max Hold Feature *Continuous Backlit Display - Easy to See Readings *Fast response time (150 Ms) for quicker work *High Accuracy Rating of +1% *Carrying Case Included *One year warranty
-
product
Universal LightProbe S2 Sensors
Optomistic Products’ Universal LightProbe S2 Sensors are designed for the In-circuit, Functional or Finished Product test of an LED’s color and/or intensity. Implemented in a unique and customizable 2-Part solution, the S2 Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.
-
product
IR Thermal Camera
AMG8833
This is the Thermal Camera FeatherWing: thanks to the Panasonic AMG8833 8x8 GridEYE sensor, it adds heat-vision to any Feather main board. Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top of your Feather board and let the board take flight!This part will measure temperatures ranging from 0°C to 80°C (32°F to 176°F) with an accuracy of +- 2.5°C (4.5°F). can detect a human from a distance of up to 7 meters (23) feet.
-
product
High Precision IR Tester
TH2684A
Changzhou Tonghui Electronic Co., Ltd.
TH2684 High Precision IR Tester is an intelligent measurement instrument that is used for rapid measurement on IR Tester is an intelligent measurement instrument that is used for rapid measurement on IR properties of electronic parts and components, dielectric materials, equipments, cables, etc. Large LCD and user friendly menu provide you easier operation.
