High-Power Amplifiers
Amplify the transmission of an RF, Audio or Optical signal.
-
product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Analog Summing Amplifier
SIM980
Stanford Research Systems, Inc.
The SIM980 Summing Amplifier has four input channels that can be added or subtracted from each other. The output noise is less than 60 nV/√Hz, and crosstalk between channels is less than -80 dB. With a bandwidth of 1 MHz, a slew rate of 40 V/ms, and input offsets that are trimmed to ±100 µV, the SIM980 is extremely useful in many analog applications.
-
product
Portable Power Amplifier
PAC60Cip
PAC60Cip is the portable conventional linear power amplifier model with six channels of current output. It is with 6*30A/210VA output, and this current amplifier is similar to PAC60Ci but it has lower output power and less weight.
-
product
Portable Power Amplifier
PA30Bip-H
PA30Bip-H portable power amplifier is designed with linear amplifier principle. It is very light portable solution with three channels of current output and four channels of voltage output.
-
product
Automatic Level Control Amplifier
RF Lambda’s automatic level control amplifiers allow customers to implement an AGC function into their system to tune the gain and stay linear with high input signals without the need to manually control the input level. Hermetically sealed options are available upon request.
-
product
Intelligent Panel Mount Meter Amplifier/ Conditioner
MODEL DPM-2
The voltage-to-frequency microprocessor makes Transducer Technique's 4-digit panel mount meters the ideal solution for meeting the measurement, display and control requirements of noisy industrial applications, OEMs and system designers. Model DPM-2 accepts any full bridge transducer. Balance and span can be selected via the front keypad, thus allowing the display to read directly in engineering units. Front panel max and tare functions are ideal for industrial weighing applications. Isolated adjustable 9-11 VDC excitation with remote sense and 90 mA drive eliminates the need for external power supplies. Rear screw terminals connectors are included.
-
product
40-67 GHz Power Amplifier
1GG6-8070
The 1GG6-8070 is a high gain, medium power mmwave amplifier. It can be used as part of a banded solution to achieve respectable mmwave power. Input and output ports are matched to 50W. The amplifier is biased with a single positive drain supply (VDD) and a single negative gate supply (VG1).
-
product
EYDFA Amplifier
a high-power, versatile amplifier designed for optical communication and other general-purpose Polarization Maintaining (PM) optical amplification applications. This compact module housing ideal for OEM integration applications.
-
product
Composite 1×6 Video Distribution Amplifier
VDA106
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
product
Amplifiers
Monacor International GmbH & Co.
Amplifier technology from MONACOR supports you in many areas. You can use loudspeaker systems or electro-acoustic systems with our amplifiers perfectly, even in large buildings. Depending on the model selected, our amplifiers and power amps are also designed for PA systems or hi-fi devices. You will also find stereo amplifiers for car hi-fi in our range. All amplifier models are designed for reliable performance in professional and private use. Like all MONACOR products, this item also combines the perfect combination of low price and high performance.
-
product
Operational Amplifiers
Operational amplifiers from ams are ideally suited to audio applications. These CMOS devices are available as single, quad or differential amps. They feature good common-mode rejection, have low input bias currents, good gain bandwidth, low total harmonic distortion and an excellent rail-to-rail output-drive capability of 200mA peak.
-
product
Millimeter Wave Amplifiers
Ducommun offers Low Noise (ALN), High Power (AHP), Full Waveguide Band (AFB) and General Purpose (AGP) amplifiers to cover the frequency range from 18 to 96 GHz. These amplifiers utilize thin-film and microelectronics manufacturing techniques and are discrete and/or MMIC PHEMT devices based. These amplifiers feature low noise, high output power, single DC power supply and wide operation temperature range. The amplifiers are offered in two categories, standard and custom-built. Both standard and custom-built amplifiers are equipped with various RF interface, including standard waveguide or coaxial connector for convenient system integration. The optional input and output integrated isolators are available as an option to further improve the port return loss.
-
product
Converter Signal Amplifier – 4…20 mA – DIN Rail
HD978TR3
Configurable converter signal amplifier with 4…20 mA (20…4mA). Input range -10 …+60mVdc.
-
product
Analog Distribution Amplifier
DA 1:54
The DA 1:54 Analog Distribution Amplifier is designed to make it simple to distribute analog signals generated by Spectrum products to multiple locations and to overcome long cable runs. The DA 1:54 consists of three separate amplifier sections that are factory- configured to operate independently or ganged together, depending upon requirements.
-
product
Low Noise Op Amplifiers (≤ 10nV/√Hz)
Analog Devices’ portfolio of low noise (≤ 10nV/√Hz) op amps includes many amps with the lowest noise performance in the industry. These high speed, low distortion (1 nV or less) op amps enable better signal fidelity in the most demanding conditions, allowing system designers to achieve the lowest total system noise performance in applications with high source impedances. We feature a considerable variety of these amps with wide supply ranges and low power.
-
product
Rack Mount Type Amplifiers
Amplifiers for each of O-, S-, C- and L-bands– Compatible with high-speed transmission (up to 100 Gbps)– Available for all signal types and protocols– Compatible with transmitters from all manufacturers– Compatible with SNMP
-
product
Variable Gain Amplifier
VGA
RF Lambda’s variable gain amplifiers (VGA) are standard amplifiers which include a gain control pin to allow the customer to tune the gain for various applications without sacrificing performance and eliminating the need to use a separate amplifier and attenuator. Hermetically Sealed options are available upon request.
-
product
RF Signal Amplifiers
The A10200 RF amplifier was designed to extend the power range of the Tabor arbitrary waveform generators and RF signal generators, yet it is compatible with many signal sources instruments.
-
product
Pulsed ESR/EPR: Pulsed Injection-locked IMPATT Amplifiers
Insight Product Company offers pulse injection-locked IMPATT amplifiers for pulse ESR/EPR experiments. Pulsed injection-locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate the amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
product
Load Cell DIN Rail Signal Amplifier
LCD20
Our intelligent strain gauge bridge amplifier is a compact, stackable microprocessor based unit specifically designed to control and monitor process applications. Flexible connection to most load cells, pressure or strain gauges over a wide range of sensitivities. The unit provides isolated current 4-20mA and voltage 0-10V analogue outputs and two digital inputs. Two set point relays can be configured to set thresholds such as net, gross, peak and valley. Powered from a wide ranging DC supply, the DIN rail amplifier is supplied with 2 part screw connectors for ease of installation.
-
product
FTTx PON Optical Amplifier (1540~1563nm)
HA5800E (5RU)
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5800E (5RU) series is a low noise, high performance, FTTP high power, multi-ports optical amplifier with gain spectrum band within 1540~1563nm. Each output port for optical amplifier has built-in well-performed CWDM. Every external up-link optical port of optical amplifier can connect with OLT PON port very conveniently. Each 1550nm (CATV)'s output optical port multiplex 1310/1490n's data stream, in order to reduce the quantity of the component and improve the index and reliability of the system.
-
product
RGB Digital Fiberoptic Amplifier
CZ-V20 Series
SUPER HIGH POWER RGB sensor Industry's best color differentiation. High resolution amplifier for triple 16-bit calculation. New Luster Detection Sensor Head. Dual digital display & Direct access. New UV sensor head for fluorescent Detection. Three detection modes for every target [Super I / C' / C+I]
-
product
Wideband Power Amplifiers
Krohn-Hite Wideband Power Amplifiers are designed to meet today's industrial needs where wideband, precision performance is required. Applications include: meter calibration, piezo transducer driving, bridging applications requiring high input and low output impedance, low distortion ac power source, ion beam deflection, vacuum tube driver, ink jet testing and design and many more.
-
product
Amplifiers
Motion Control Systems'' linear amplifiers are high performance servo controllers that produce very smooth sinusoidal motor currents using a linear amplifier output stage. In combination with a sinusoidally wound MCS brushless motor, the linear amplifier can achieve extremely precise rotational control with less than 1% torque ripple, no acoustic noise and almost undetectable levels of electromagnetic interference. Standard programmable features allow greater design flexibility, easy installation and start-up.
-
product
Motion Control Terminal Board For Panasonic MINAS A4 Servo Amplifiers
DIN-814-A40
- Panasonic MINAS A4 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134
-
product
Third Party RF Amplifiers
We work closely with major manufacturers to supply a range of oscilloscopes, function generators and power amplifiers. We are the UK agent for the leading manufacturer of RF amplifiers Electronics and Innovation.
-
product
Loop Powered Trip Amplifier With Dual Relay Output
SEM1636
The SEM1636 monitors a (4 to 20) mA loop and provides two independent change over trip contacts set to trip at any point within the (4 to 20) mA range.
-
product
Waveform Amplifiers
Most waveform generators are limited to 20V pk-pk EMF output level. The WA301 waveform amplifier can be used to increase that level up to 30V pk-pk.
-
product
Shortwave Power Amplifier
OM2501A (OM3501A)
The OM Power model OM2501A and OM3501A are designed for all short wave amateur bands from 1.8 to 29.7 MHz (including WARC bands) and all modes. OM2501A is equipped with a FU728F or GU84B ceramic tetrode and OM3501A is with GU78b ceramic tetrode.
-
product
Fiber Optic Sensors And Amplifiers
Omron’s high-performance fiber optic sensors and amplifiers come in a wide variety of configurations to meet your specialized requirements.
