Discharge
-
Product
Three-Pole Lighting And Surge Arrestor
PIVM12,5-275/3+0 Vseries
-
PIVM12,5-275/3+0 Vseries is a three-pole lightning and surge arrester Type 1+2 according to EN 61643-11 and IEC 61643-11. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 – 1 (according to IEC 1312-1 and EN 62305), where they provide the equipotential bonding and discharge of both, the lightning current and the switching surge, which are generated in power supply systems entering the building. The use of the lightning current arresters PIVM12,5-275/3+0 Vseries is mainly in the power supply lines, which are operated as TN-C system. The main use of PIVM12,5-275/3+0 Vseries arrester is in structures of LPL III – IV according to EN 62305 ed.2. The marking M specifies a type of construction with removable module.
-
Product
Vibration Sensors
-
SKF Condition Monitoring Center
Various machine operating conditions concerning temperature extremes, magnetic fields, vibration range, frequency range, electromagnetic compatibility (EMC) and electrostatic discharge (ESD) conditions and the required signal quality necessitate the need for a variety of sensors.
-
Product
Solution for Industrial Monitoring
PDScope
-
Techimp PDSCope is a brand new product of the PDCheck family particularly designed to suit all the requisites of the Techimp TiSCADA systems for on-line monitoring of diagnostic quantities in electrical assets.Techimp PDSCope is a powerful PD analyzer based on Techimp TF Map technology (patented) allowing preliminary noise rejection and automatic calculation of statistical parameters relevant to Partial Discharges.
-
Product
Universal PD & EMI analyzer
Spark P3
-
Doble Spark P3 is a universal partial discharge (PD) and electromagnetic interference (EMI) analyzer that uses a software defined radio signal detector to identify characteristics of insulation system deterioration that could lead to the failure of high voltage equipment. It detects signals from suitable sensors in a frequency range between 9 kHz to 2 GHz for PD and EMI, and DC to 500k Hz for acoustic and reference voltage measurements.
-
Product
High Frequency Current Transformer
HFCT Ø 140mm
-
Techimp Clamp High Frequency Current Transformer model 140 is an inductive sensor for partial discharge measurements. It is suitable for online /off line PD tests on : large diameter cables ; grounding rod bar ; etc. A TNC termination is available to connect the Clamp HFCT 140 to the TechImp PD analyzer : PDCheck , PDBase etc. The arrow indicates the requested input current (Iin) direction to get coherent output voltage (Vout) polarity respect to ground. When the sensor is installed with the arrow directed to ground, the detected voltage signal (Vout) has the same phase of the input current (Iin).
-
Product
76kWh Lithium Battery 384V 200AHSolar Energy Storage LiFePO4 battery System
SPVLI-76KWH
-
Zhejiang Sandi Electric Co., Ltd
SANDI ESS lithium battery system is composed of lithium battery modules, BMS system, PV charge controller, AC/DC Charger, central control unit CCU, temperature detector, integrated structure and other parts; the solar panels in the system are battery storage and power for output; BMS module completes the detection and control of voltage, current, temperature, SOC, SOH and charging and discharging related parameters of power battery pack; PV controller and inverter realize bidirectional AC/DC function to meet the charging and discharging conversion demand of power battery pack; each detector is used to monitor the ambient temperature in real time to ensure the safety of the system.
-
Product
Single-Phase Transformer Winding Resistance Meters
RMO-TT Series
-
RMO-TT series is perfect for measuring winding resistance of inductive objects such as power and distribution transformers or autotransformers. Additionally, every transformer resistance meter from RMO-TT series can analyze:tap changers,generators,electrical motors,high-current busbar joints,cable splices,and welding joints.Transformer demagnetization can also be performed with all RMO-TT instruments.The series is consisted of 3 models, with maximal test current from 40 A (RMO40TT) to 100 A (RMO100TT). RMO100TT is the only portable transformer resistance meter in the market with 100 A DC output current.The three independent channels enable testing of three windings in series. Consequently, a user can measure winding resistance in every tap position of an on-load tap changer without discharging between the tests.In addition to winding resistance measurement, a user can perform a detailed on-load tap changer analysis by analyzing recorded graphs (10 kHz sampling rate) and by measuring vibrations on an external tap changer tank.All RMO-TT instruments have a built-in tap changer control unit. Because of this, it is possible to remotely control on-load tap changer (OLTC) directly from the device. Also, a user can program DV-Win software to do everything automatically – running winding resistance tests and changing OLTC tap positions.The DV-Win software also enables control and observation of the test process, as well as saving and analyzing the results on a PC. It provides a test report, arranged in a selectable form as an Excel spreadsheet, PDF, Word, or ASCII format. Additionally, DV-Win measures and calculates the OLTC transition time, the ripple and the winding resistance for each tap changing operation. The software can also perform the calculations necessary for the “Heat Run” test.All results can be exported in the report format.
-
Product
48V / 300 Amp Load
BD18-48P-24/12
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 12V, 24V and 48V Battery systems and isextremely cost effective.
-
Product
Inrush Current Generators for Zno Production Line
-
Shanghai Guantu Technology Co., Ltd.
Inrush Current Generator Standard: IEC61008, IEC61009, I61051/61643, ANSI C62.31, C62.33, C62.35, TU K20, K21, K44, K45, UL943Inrush Current Generator Features1. LCD screen display, built-in computer control, man-machine dialogue, easy to operate.2. Program-controlled high-voltage power supply, high voltage stability and precision3. Imported non-inductive high-power resistors are used to ensure the consistency of surge waveforms4. The main switch adopts electronic switch discharge mode, and the output polarity is automatically switched
-
Product
Walk in Chamber for Altitude Simulated Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
Walk in Chamber for Altitude Simulated Test Relative Standard test requirementsTest Object: battery pack and systemTest Conditions: Altitude 4000m or the equate air pressure condition, atroom temperature.The test objects stay in the test condition as Item 2 for 5 hours.Subject the test object to 1C(no more than 400A) constant current discharge until reaching the cutoff condition.After testing, observe for 2h under the room temperature.
-
Product
Lightning Surge Generator
CDN-5810
-
Shanghai Sanki Electronic Industries Co., Ltd.
CDN-5810 signal line/data line coupling decoupling network, unshielded symmetrical communication line suitable for surge pulses and ringing wave pulses, designed according to Figure 10 of the new standard IEC61000-4-5.Ed3. It also satisfies ringing Figure 10 requirements of wave standard IEC61000-4-12.Ed2. According to the characteristics of the line, the pulse coupling can be realized by gas discharge tube, capacitor, diode and other different methods.
-
Product
Radiometer
X1-1-RCH-116-4
-
The X1-1 radiometer from Gigahertz-Optik features an RCH-116-4 detector and is ideal for measurement of the irradiance of high power LEDs in the UV-A and blue light range. The device can accurately measure irradiance levels of up to 40,000 mW/cm². One of the outstanding features of the RCH-116-4 detector is its proven concept of a passive radiation absorber coupled to a UV sensor. This provides stability even in high temperature and intense UV radiation environments. In addition to the passive radiation absorber, the device also has a cosine-corrected field of view. The sensor’s housing also serves as a handle. The battery-powered X1-1 optometer supports a usable dynamic range from less than 1 mW/cm² to 40,000 mW/cm² thanks to its high-end signal amplifier. It can be used to perform precise measurements of up to 5 standard LED wavelengths for which the detector was calibrated for active irradiance. In addition to the CW measurement function, the device also has a dose measurement function. The radiometer can be used with other detectors from the RCH series. e.g. for gas discharge lamps. Remote control of the device is possible via its user software and a software development kit is offered for integration of the device in the user’s own software.
-
Product
Static Grounding for Process Plant & Equipment
Earth-Rite MULTIPOINT II
-
The Earth-Rite® MULTIPOINT II is a unique multi-channel static grounding system that can monitor the simultaneous grounding of up to eight (8) individual pieces of equipment at risk of discharging electrostatic sparks.
-
Product
Battery Analyzers
CA 1550 – Commercial Version
-
*Portable Battery Charger / Analyzer.*0-25 Amp Charge.*0-50 Amp Discharge.*Fully adjustable.*115/230 Volt AC Input.
-
Product
Programmable DC Electronic Loads (conventional and regenerative)
-
Elektro-Automatik GmbH & Co.KG
Our programmable electronic loads are composed of an optimum mix of analogue- and digital technology (µ-controller/FPGA based). By combination of standardised electronic platforms out of a modular structure, we generate a large portfolio of electronic-load series, perfectly adapted in power, function, performance and cost to the numerous applications in industrial environment and R&D. EA programmable electronic loads are available in conventional technology (heat dissipating) and as “regenerative” loads. The latter allows, specifically under long-term testing condition (e.g. battery discharging) a full amortisation of its invested value by its energy-saving capability, similar as with Photovoltaic installations.
-
Product
Charge/Discharge System Controller
PFX2500 Series
-
PFX2500 Series is a high performance Charge/Discharge system controller that takes measurements in combination with our DC power supply and electronic load in order to evaluate test sample (electric storage elements such as secondary batteries) characteristics. It is also capable to perform evaluation test with high-performance, large capacity and wide range of rating with the combination of DC power supply and electronic load.Execution of the test is conducted by the exclusive application software. The test corresponds to long time continuous test and synchronization test with temperature chambers with the multiplexed protection performance. In addition, easy data editing is also capable with fulfilling graphic performance.
-
Product
48V / 250 Amp Load
BD15-48P-24/12
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 12V, 24V and 48V Battery systems and is extremely cost effective.
-
Product
110V / 100 Amp Load
BD12-110P-48/24
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 110V battery systems and is extremely costeffective.
-
Product
PD (Partial Discharge) Tester
-
Weshine Electric Manufacturing Co., Ltd
Using the Windows system operating platform, you can freely choose ellipse, straight line, sine wave display, two-dimensional, three-dimensional graphic analysis mode, spectrum window, Q-V-F three-dimensional characteristic window, and static detailed measurement, observation and analysis of partial discharge pulse of one-cycle test voltage .
-
Product
Ion Blower Nozzles
-
VARIO discharge products consist of a separate AC power supply unit for connecting one or more Eltex discharging components. In SINGLE discharging, the voltage generation (power supply unit) is integrated in the bar.
-
Product
Pressure Relief Valves
-
WITT is a manufacturer of safety relief valves or pressure relief valves. Safety relief valves respectively pressure relief valves or pressure safety valves are designed to protect against overpressure by discharging pressurised gases and vapours from pipelines, pressure vessels and plant components. Safety relief valves are often the last line of defence against explosion – and such an explosion could be fatal.
-
Product
Battery Discharger & Capacity Tester
IDCE-8X0
-
Fuzhou Fuguang Electronics Co., Ltd.
Wide Range: IDCE-8X0CT series can cover 10V~480V for multiple batteries test requirements like telecom (48VDC), powerutilities (110VDC, 220VDC), UPSs (300-60 VDC), traction batteries(12-96VDC)etc.
-
Product
Partial Discharge Measurement and Analysis System
UHF 800
-
Our UHF 800 is a system for measuring and analyzing partial discharges in the ultra-high frequency (UHF) range in testing environments with high levels of external noise.
-
Product
Testing of Rear Axle Steering
-
*2 high-precision servo axes for linear load simulation*Communication via CAN / Flexray*Function and noise measurements (NVH)*Supply and discharge of the test specimens via WTs on double belt conveyors*Connection to the production control
-
Product
Lightning Warning Sensors
-
Lightning warning sensors measure the local, atmospheric electric field at the earths’ surface and the fluctuations in field strength. By monitoring the field strength, the potential for cloud-to-ground (CG) lightning discharges can be detected, and advance warning can be made when conditions are becoming favorable for lightning.
-
Product
Real-Time Online Monitoring to Detect and Analyze Potential Partial Discharge (PD) Signals and Insulation Faults using UHF, AE, and HFCT
PDMonitor
-
Power Monitoring and Diagnostic Technology Ltd.
The PDMonitor, which utilizes Ultra High Frequency (UHF), Acoustic Emission (AE) and High Frequency Current Transformer (HFCT) sensors and is designed to conduct real time online monitoring to detect and analyze potential Partial Discharge (PD) signals and insulation faults before they lead to breakdown or catastrophic failure in power assets. The system provides the developing trend of the PD, when occurring, as alarms in real time, thus helping to predict the insulation degradation status of the asset, prevent sudden accidents, and provide an effective database for Condition-Based Maintenance (CBM) of power assets.
-
Product
20KV 30KV Electrostatic Discharge Generator ESD
ESD-202AX
-
Shenzhen Chuangxin Instruments Co., Ltd.
ESD simulator is in full compliance with IEC 61000-4-2, EN61000-4-2, ISO10605, GB/T17626.2, GB/T17215.301 and GB/T17215.322. The ESD generator is designed for the assessment of electrical and electronic equipment to withstand ESD performan
-
Product
Digital Insulation Resistance Tester (CE)
MIS-D
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*The big digital and bar graph LCD display with back light enabled easy observation. Especially useful when working in dark place.*Hand free and continuous measurements with custom made switch.*Safe design with built in automatic discharging function for any capacitors present in the circuit.*The voltage in the circuit or capacitor can be checked by warning lamp for safe insulation measurements.*Data hold and auto power off function.*Compact, light weight and heavy duty rugged case.
-
Product
Capacitors
-
Offering you a complete choice of products which include repeated charge discharge test set, leakage current tester and million megohm meter.
-
Product
Partial Discharge Measurement Calibrator
DAC-CP-2
-
DAC-CP-2 is a calibrator for partial discharge measurements. The electric charge enables to generate up to max 10000pC. It is battery-operated and can be charged by connecting to the measuring instrument (DAC-PD-3).
