Product

Mating Coax Connector and 20 Coax Pins Crimped (both ends) to 3' Wires

GX96405

-

Marvin Test Solutions, Inc.

GX96405 - Marvin Test Solutions, Inc.

Mating coax connector and 20 coax pins crimped (both ends) to 3 ft wires

Product

Mating Coax Connector and 20 Coax Pins Crimped (both ends) to 5' wires

GX96405-60

-

Marvin Test Solutions, Inc.

GX96405-60 - Marvin Test Solutions, Inc.

Mating coax connector and 20 coax pins crimped (both ends) to 5 ft wires

Product

Multimeter with Cable Checker Phone Test Lan Wire Test

VA43

-

Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD

VA43 - Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD

Lan Telephone test multimeter: VA43 is a multimeter with lan wire test. phone test .cable check.

Product

Cable Tester, HDMI Cable, Digital, LAN Tracer, Talk Mode, Tone Generator

TCT-320

-

Tenma

TCT-320 - Tenma

Designed to check and troubleshoot pin connections of HDMI cables. Tests the continuity of each pin of HDMI cable prior to installation to save time on install.

Product

Vibrating Wire Peripherals

-

Campbell Scientific, Inc.

Campbell Scientific, Inc.

Many Campbell Scientific vibrating-wire peripherals enable dataloggers to read vibrating-wire sensors (also known as vibrating-wire or vibrating-strip transducers). These sensors measure strain, load, pressure, and water level, and they output a frequency signal generated by a vibrating filament. Campbell Scientific also offers vibrating-wire dataloggers that read the sensors directly.

Product

Automatic Wire Test Set

AWTS

-

Eclypse International

AWTS - Eclypse International

The Automatic Wire Test Set (AWTS) is automated test equipment that aids wiring diagnostics of electrical and electronic devices. The Test Control Unit (TCU) uses resistance measurements, capacitance measurements, and AC/DC voltage measurements to perform continuity, insulation, and isolation tests. The AWTS Laptop CPU, hereafter referred to as CPU, controls the AWTS. The Eclypse Language Integrated Test Environment (ELITE) is application software that controls the TCU. The majority of the hardware for a test is contained in the TCU. The 128pin connector on the TCU front panel provides 128 energizable test points. Switch Modules (SM) can be connected in sequence or daisy chained to the TCU and provide an additional 1024 test points; 128 of those are energizable.

Product

Electrical Circuit / Wire Harness Analyzer

ECAD System 2005

-

CM Technologies Inc.

ECAD System 2005 - CM Technologies Inc.

The ECAD System 2005 is a suite of test instruments for both lumped and distributed data for analysis of electrical circuits and/or wiring harnesses. ECAD is completely self contained, and has a built-in multimeter, impedance meter, TDR, and megohmeter.

Product

Hipot Wire Harness Testers

NX Hipot

-

Dynalab Test Systems, Inc.

NX Hipot - Dynalab Test Systems, Inc.

* 50 to 1500VDC Hipot Testing* 50 to 1000VAC (optional) * 5Mohm to 1Gohm Insulation Resistance * Simple 4-button user interface * Tests for continuity and shorts * Tests a variety of components * Precision resistance measurements * Continuous high speed scanning for real time complete status information of harness assembly progress * Keyed security access and control * Built for rough industrial environments * 2 serial ports for connection to printers and scanners * Standalone operation * Uses a high capacity memory card * Available from 64 to 1024 test points * Networkable

Product

IV Curve Tracer

IVCT

-

PSE Instruments GmbH

IVCT - PSE Instruments GmbH

In recent years, we have been developing a sophisticated IV curve tracer for PV modules including a maximum power point tracking (MPPT) function. The IV curve tracer is designed for operation with any market-available steady-state solar simulator. Through our web-based software design, the operator can supervise the test results from every computer in a company network. The software contains functions such as an irradiation sum counter that helps to check requirements stated in a stabilization test like they are defined in IEC 61215 (MQT 19). We have also included a correction function to correct the traced IV curves to standard test conditions (STC) when the user enters the required temperature coefficients. One of the most important features is the multi-IV curve tracing function, which enables the user to display more than 150 IV curves in one graph. This eases the analysis of the weakest cells in hot-spot tests, which are required in IEC 61730 (MST 22) and IEC 61215 (MQT 09).

Product

3'Harness, 50-Pin Male D-sub Connector on one end, loose wired (numbered) other end

GT97107

-

Marvin Test Solutions, Inc.

GT97107 - Marvin Test Solutions, Inc.

3' harness, 50-pin male D-sub connector on one end, loose wired (numbered) other end.

Product

Multi-purpose Cable Tracer and Non-contact Voltage Detector

168 CB

-

Standard Electric Works Co., Ltd

168 CB - Standard Electric Works Co., Ltd

● Four transmitter plug types - RJ-11 - RJ-45 - COAX - Alligator clips ● Two unique audible tones: - Fast alternating tone - Slow alternating tone ● Telephone line polarity check - Tip side - Ring side● Cable tracing ● Telephone line status check - Clear line - Busy line - Ringing line ● Continuity check.● Transmitter plug storage.● Easy to store different kinds of transmitter plugs (RJ-11, RJ-45, COAX, and alligator clips).● Easy to carry.● Flashlight function.

Product

Provides 3 Wire Voltage Output

SEM1620

-

Labfacility Ltd.

SEM1620 - Labfacility Ltd.

The SEM1620 signal conditioner provides a 3 wire isolated voltage output signal and accepts RTD, Thermocouple, mV and passive current sensor inputs

Product

Non-destructive Eddy Current Testing of Long Products such as Tubes, Rods, Wire, and Profiles

DEFECTOMAT® Product Familiy

-

Foerster Instruments, Incorporated

DEFECTOMAT® Product Familiy - Foerster Instruments, Incorporated

The DEFECTOMAT systems by FOERSTER were specially developed for quality testing and process monitoring of long products. From hot testing to all bright steel processing steps, the surfaces of semi-finished products made from austenitic, (non) ferromagnetic metals can be tested for defects. The DEFECTOMAT systems operate in a contactless and non-destructive manner in accordance with the eddy current method and are used for detecting short defects, such as holes or localized defects and transverse defects. The systems detect defective materials fully automatically and reliably. Defects can be marked, classified, and automatically discarded. the test speed of up to 150 m/s facilitates 100% testing, even at high production speeds. The systems benefit from low operating costs and frugal energy consumption as well as low maintenance costs, few wear parts, and low use of materials.

Product

PV Analyzer I-V Curve Tracers

-

Solmetric Corporation

Solmetric Corporation

The Solmetric line of PV Analyzer I-V curve tracers are widely used in Commissioning, Auditing, O&M, and Troubleshooting of PV systems.

Product

Cable Tracers

180 CB

-

Standard Electric Works Co., Ltd

180 CB - Standard Electric Works Co., Ltd

● The Amplifier Probe is designed to identify and trace     wires or cables within a group without damaging     the insulation.● Works with any Tone Generator to identify wires.● Volume control for increased sensitivity and adjustable    to suit work environment.● Recessed ON/OFF button prevents battery drain.● A phone jack is designed for headset or handset.

Product

Temperature Wire Sensors

-

Omega Engineering, Inc

Omega Engineering, Inc

Temperature Wire Sensors

Product

Fine Wire Versatile Thermocouples ANSI

-

Labfacility Ltd.

Labfacility Ltd.

An exposed junction thermocouple is the simplest form of thermocouple. It consists of two pieces of thermocouple wire joined together with a welded bead. Since they can be made very small, an exposed junction thermocouple can provide a very fast response time.

Product

3 Wire (Analogue) Earth Resistance Tester

1105 ER

-

Standard Electric Works Co., Ltd

1105 ER - Standard Electric Works Co., Ltd

● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● In addition to facilitating for precision measurement, test leads for simplified two-wire measuring system also are supplied as standard accessories.● Battery operated.● Battery life indicator. ● Calibration performed with supplied test leads.

Product

Field Portable Wire Analyzer

Model 2635

-

DIT-MCO International

Model 2635 - DIT-MCO International

The perfect tester for field use is rugged, mobile, and lightweight, without sacrificing the functionality and power of a larger system. That tester is found in the Model 2635. Weighing 32 pounds (14.5 kg), this wiring analyzer handles up to 400 test points of Series 10 switching per unit. The 2635 can be powered from any AC source 100-240 VAC or 28 VDC so you can use it anywhere in the world.