Cable Trackers
Identify a wire's path.
-
product
USB Cable
780534-01
USB Cable - The USB Cable works with SuperSpeed or Hi-Speed USB hosts and devices but is backward-compatible with USB 1.1 hosts and devices. You can use this cable for vision acquisition hardware, CompactDAQ or CompactRIO systems, or any device that supports USB Cables.
-
product
Cable Assembly, 25-Pin D-Type, Female to Unterminated With Ferrules, 2m
40-972-025-2m-FU
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Cable Testers
E445
Tests 3 pin XLR leads, 2 and 3-pole A-gauge jack leads, RCA (phono) leads, most commonly used fuses, and other continuity paths using test leads supplied. Continuity indication by buzzer.
-
product
Energized Cable Sensor
The purpose of the Energized Cable Sensor is to allow the lineman to readily determine whether a URD cable is energized. The sensor consists of an amplifier which is designed to give a meter reading when the small AC voltage between the semi-conductive sheath and the concentric neutral of the energized URD cable is applied to the test probe. The amplifier is housed in a rugged phenolic case. Sensor may be used to check for energized condition on concentric-neutral cable below an elbow without test points. At cable mid-span (left), hose clamps bridge all strands of concentric neutral at the test location. Sensor’s neutral lead clips to one of the hose clamps. Tip on probe lead contacts only semi-conductive cable sheath to test for voltage presence.
-
-
product
Sediment Tracker™
Track the settling location of sediment caused by stormwater runoff. The Sediment Tracker's™ high-drag drogue lowers at a controlled rate approximating sediment falling to the ocean floor.
-
product
Cable Identifier
K&S Engineering and Scientific Ltd
K&S Engineering and Scientific LTD's Cable Identifier Set offers the user a compact, portable solution for cable identification. Depending on the user preference, the Cable Function Generator and Cable Identifier Unit can be jointly housed in a rugged briefcase, or alternatively, for the user requiring a more rugged unit, can be delivered as two individual units each with their own carry-case. With the Cable Identifier Set, power optimum levels are selected by means of a rotary switch and the power levels are displayed on a meter located on the Cable Function Generator. As the Cable Identifier Unit is capable of detecting magnetic fields around mains cables it has the added advantage of the user being able to use this as a stand-alone unit to detect power cable configuration.
-
product
CABLE TESTER
MCT-7
Whirlwind Music Distributors, Inc.
This diagnostic cable tester has connectors for analyzing almost any type of cable combination. The convenient rotary switch allows testing of each conductor within the cable and can determine the internal wiring configuration. Tests NL4, 5 pin DIN, BNC, XLR, TRS, RCA and 3.5 mm types.
-
product
Datapaq Reflow Tracker System
Monitor the temperatures for every soldering application – including wave, reflow, vapor phase, selective and rework stations – in real-time with the Datapaq Reflow Tracker Systems. Ideal for the electronics manufacturing and semiconductor applications.
-
product
Cable & Antenna Analyzers
Site engineers and technicians have been using sweep testers also known as cable and antenna analyzers to validate installations or to find trouble locations and imperfections in wireless sites.
-
product
Cable Fault Locators
Every day, GAOTek cable fault locators are used by electricians and technicians to find faults and breaks in underground electrical and communications cables.
-
product
Recloser and Sectionalizer Test Cables
OMICRON offers a comprehensive range of cable packages as an accessory to CMC test sets for testing various recloser and sectionalizer controls.
-
product
160 Pin Female DIN to QuadraPaddle Flying Lead Cable, 72", 024070
VFL103124-072
Vendor Flying Lead (VFL) Cable, 160 Pin Female DIN to QuadraPaddle Leads, 24AWG Twisted Pair, 80 T/P's(1:2) 160 connection points, M2.5 x .45 fastener, CONN: 024070 WIRE: VPC, for PXI-2737, PXIe-2738 families, VPC Contact 610138216 - QP RCV (22AWG-28AWG) (5 AMP/25 mΩ MAX), 20" length.
-
-
product
Cable Assembly, 9-Pin D-Type Male to Unterminated With Tinned Ends, 1m
A009DM5-T-0A100
A range of 9-Pin D-Type cable assemblies with unterminated connections at one end and constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation.
-
product
Cable Assembly, Receiver, QuadraPaddle, 36", 78-Pin Female D-Sub
540034010240
Cable Assembly, Receiver, QuadraPaddle, 36", 78-Pin Female D-Sub
-
-
-
product
GPIB Cable, 6 Meter
10833F
The Keysight 10833F (6 meter) GPIB cable is engineered for exceptional reliability and durability even under the harshest conditions. When you buy Keysight GPIB cables, you can be sure of automatic, seamless compatibility between computers and instruments throughout your system. GPIB interface cables, cards, and software for your computers make it easy for you to access and control instruments and exchange data - and it all starts with the cables to connect your computer and instrument. Keysight GPIB cables are fully compatible with the IEEE 488.1 mechanical specification.
-
-
-
product
ITA, I2 Micro ICon, Wired, QuadraPaddle, 36", Flying Leads
410130409
ITA, i2 Micro iCon, Wired, QuadraPaddle, 36", Flying Leads This i2 Micro iCon comes wired with a flying leads cable assembly containing 168 QuadraPaddle patchcords with 24 AWG PVC.
-
product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Tinned Ends, 0.5m, Screwlocks
A068SMR-T-6B050
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Tinned Ends, 2m, Spring Latch
A068SFR-T-5B200
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
product
External PCIe Cable Adapter
PXIe7800 / PCIe7800 / PCIe7801
The external cable adapter family supplies a high speed PXI Express x1 interface. Due to the low latency and high data transfer rate it is pefectly suitable for multi-channel systems with high data volumes and high speed test environments.
-
product
Wire Trackers
Used to locate wires and identify circuits and breakers without having to put unnecessary holes in walls or waste time guessing to find the correct wire in a bundle or run.
-
product
Cable Testers
The CableTool uses TDR (Time Domain Reflectometry) technology to quickly identify an open or a short from 0 to 2,500 feet within a foot of the fault.
-
product
Cable Assembly, Receiver, TriPaddle, 20", 10 Position Combicon and 4 Position Omnimate
540295010101
Cable Assembly, Receiver, TriPaddle, 20", 10 Position Combicon and 4 Position Omnimate
-
product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Ferrules, 1m, Screwlocks
A068SFR-F-6B100
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
product
Cable Assembly, 9-Pin D-Type Female to Unterminated With Tinned Ends, 1m
A009DF4-T-0A100
A range of 9-Pin D-Type cable assemblies with unterminated connections at one end and constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation.
