Traces Wire
Identify a wire's path.
-
Product
Gauge Type T Thermocouple Wire
W-TW-40P
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Trace Moisture Analyzer
PPM1
-
Model PPM1 is a trace moisture analyzer designed specifically for monitoring moisture levels in dew point and PPM units. This trace moisture analyzer utilizes an electro-chemical (P205) sensor in combination with a proprietary semi permeable diffusion membrane.
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, 90 Series, 2 VHDCI Male
510140158
Pull-Thru Adapter
Pull-Thru Adapter, Wired, QuadraPaddle, 90 Series, 2 VHDCI Male.
-
Product
Wire Damage Test Device For Pull Testing
IEC60884 FIG11
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 FIG11 Wire damage test device for pull testingThe wire damage test device is a special test instrument designed and manufactured according to the requirements of IEC884 Figure 11, , etc. It is mainly used to judge whether the screw-clamp type terminal is in design and structure.
-
Product
Minigrabber® Test Clip For Max. .090" Wire Dia, Do-It-Yourself
3925
-
Minigrabber? test clip for max. .090" wire dia, Do-It-Yourself, available in ten colors
-
Product
System Trace Emulators
XDS560v2
-
The XDS560v2 System Trace Emulator is the second generation of the XDS560-class emulator design from Texas Instruments. It provides cost effective real-time emulation, debugging, and high-performance System Trace (STM) for Texas Instruments devices over both USB and Ethernet PC interfaces.
-
Product
Wired Hazard Monitoring
-
Grain dust is extremely volatile and can easily explode with the proper ignition source in confined spaces. OSHA has mandated that grain elevators in Class II, Division 1 environments must have the 3 monitoring sub-systems for elevator safety (1910.272(q)(4)(ii), 1910.272(q)(5), 1910.272(q)(5)).
-
Product
U Type Glow Wire Loop
IEC60695-2-10
-
Shenzhen Chuangxin Instruments Co., Ltd.
Thermo resistance, spare part set of Glow Wire Apparatus Acc IEC60695-2-10. Thermo resistance loop is a wire loop that is defined at a temperature and is pressed against a standardized test platelet made of plastic (or other materials) for a prescribed period of time under precise test conditions.
-
Product
Four Wire Modem for SEL Mirrored-Bits
MBT 9600
-
Application specific features set the MBT9600 Four Modem apart from the conventional high speed modems. Its compact size and ease of installation make the MBT9600 an ideal, low cost alternative to conventional audio tone teleprotection systems.The circuitry is ideally suited for use over private networks such as conventional voice channels over analog microwave.
-
Product
Banana-Triax Adapter For 2‑Wire (Non-Kelvin) Connection
N1297A
Accessory Kit
The N1297 Series is a collection of banana-triax adapters for the Keysight B2900 Series precision source measure unit (SMU). It consists of both 2-wire as well as 4-wire connection requirements.
-
Product
Wire Strippers
-
Thermocouple wire, cable and OMEGACLAD™ wire at strippers. Specialized wire and cables require specialized tools. Make your choice with a range of diameters and gauges.
-
Product
Bench-Top Wire Crimp Pull-Force Tester
PT-1500
-
PT-1500 Bench-Top Wire Crimp Pull-Force Tester, Manual Lever-operated for 5.84mm 8-30 AWG
-
Product
Trace Moisture Analysis System
-
Analyzing moisture, and how much of it, is critical to the performance of petroleum products, as well as infrastructure and product integrity. For example, moisture in petrochemical feedstock can cause pipelines and valves to freeze, as well as poison some catalysts. One popular method used to analyze for moisture is Karl Fischer Titration (KFT). KFT has a wide dynamic range but has difficulty in measuring relatively low amounts of moisture. In addition, there are the well-known problems of side reactions and known interferences.
-
Product
20 Channel Multiplexer (2/4-wire) Module for 34970A/34972A
34901A
Multiplexer Module
The Keysight 34901A module for the 34970A/34972A Data Acquisition/Switch Unit is the most versatile multiplexer for general purpose scanning. It combines dense, multi-function switching with 60 channel/second scan rates to address a broad spectrum of data acquisition applications.
-
Product
Corona Resistant Tester of Enamelled Wire
DPT-1000S
-
Shanghai Dean Electrical Co., Ltd
·The tester is comply with the requirements of standards GB/T 1707-2008, GB/T 24122-2009, GB14711-2013, meet the requirement of standard JB/T 10930-2010;·Multiple samples can be tested at same time;·Used for testing the feature of high frequency pulse resistance (performance of Corona-resistance).
-
Product
Drawing Die And Wire Measurement
Wire Diameter And Roundness Measurement
-
Optik Elektronik Gerätetechnik GmbH
The DGMS is a measuring system for diameter and roundness of wires, drawing dies and enameling dies. The wire diameter is measured highly accurate by an image processing system. To measure the roundness, an additional special holder is necessary to rotate the wire for the diameter measurement in several azimuths. The accuracy of the measurement is ‹1micron.
-
Product
One Wire Communication Board
MS 1727
-
- Digital serial bus communication with low speed data over a single line, Both signaling and driving power over a same single signal.- Protocol used in small inexpensive devices. Such as digital thermometer, weather instruments, laptop sub module, authenticate system and some cell phone battery packs.- Always master only initiates the communication and in overall in charge of the network.- Bus communicates with master and slave at a low data rate of 12kbps.- All terminals in the network are communicating by half-duplex mode.- Maximum of 255 nodes in each 1-wire network- Each data transaction will start with 480micro second low RESET pulse.
-
Product
Process Trace Oxygen Analyzer
Model 3020T
-
Teledyne Analytical Instruments
The Model 3020T is a microprocessor-based instrument for detecting oxygen at the parts-per-million (ppm) level in a variety of gases. This instrument serves as the explosion-proof, bulkhead-mount version of the 3000 Series. Simple menu choices, externally accessible command switches, and dual LCD and LED displays make setup and operation clear and quick.
-
Product
3 Wire (Digital) Earth Resistance Tester
2120 ER
-
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● 0Ω adjustment.● Battery operated.● Data hold function.● Low battery indication.● Calibration performed with supplied test leads.
-
Product
Wire Crimp Testers
-
Imada offers manual and motorized wire crimp test systems in either vertical or horizontal configurations.Lever-operated systems offer basic functionality and rapid destructive testing up to 220 lbf.Motorized systems have speed control and are capable of destructive or force-controlled non-destructive testing up to 1100 lbf.Choose from manual or automatic wire-gripping fixtures.Digital gauges offer data output for analysis with data acquisition software.Create your own custom configuration or consult our application specialists.
-
Product
Glow Wire Apparatus
GW-4
-
Is designed to perform tests specified in many standards to check Resistance to Fire in Insulating parts. The best method for testing electro-technical products with regard to fire hazard is to duplicate exactly conditions occurring in practice.
-
Product
Test Lead Holder For Wires Up To 0.450In (11.43mm) Dia.
2708
-
Test Lead Holder for Wires Up to 0.450in (11.43mm) Dia.
-
Product
Wire Abrasion Tester
SG-D03DG
-
This machine is mainly based on UL1581 / UL83 standard abrasion test wire and cable testing requirements .
-
Product
4 Wire Earth Resistance & Resistivity Tester
4235 ER
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Earth resistivity (ρ) test.● Earth testing at 20Ω, 200Ω, 2kΩ.● Earth voltage measuring : 0-300V AC.● Automatic C spike check.● Automatic P spike check.● 2-Wire test, 3-Wire test, 4-Wire test.● LCM display.● Auto ranging.● Auto power OFF.● Data hold.● 200 measurement results can be saved in the memory and recalled on the display.● Interval between auxiliary earth spikes is 1.0~50.0m.
-
Product
Wired Adapter for PXI, for National Instruments PXI-4110
510109469
Pull-Thru Adapter
Wired adapter or pull-thru from a 64 position TriPaddle receiver module to one 6 position Mini-Combicon plug and one 2 position Mini-Combicon plug.
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, 160 Pin Female
510140255
Pull-Thru Adapter
Pull-Thru Adapter, Wired, QuadraPaddle, 160 Pin Female
-
Product
Test Lead Holder For Wires Up To 0.210In (5.33mm) Dia.
1508
-
Test Lead Holder for Wires Up to 0.210in (5.33mm) Dia.
-
Product
Heavy Duty Circuit Tester with 12' Retractable Wire & Battery Clip
27300
-
Features an extra long wire that stretches up to 12 feet for use, then automatically retracts. Quickly and easily check electrical circuits and accessories on 6 and 12 volt systems. Great for use on cars, trucks, boats, trailers, motorcycles, airplanes and snowmobiles. Heavy duty ground clip with insulator. 3 1/4" standard length probe
-
Product
Wire Damaged Tester
WDT-1
-
This equipment is designed and manufactured according to corresponding regulation in standard IEC884-1, GB299.1-96, GB16915.1-97 and other electronic accessories relevant standard. Mainly used to test damage degree of fixed connection components lead wire of with thread clamping type and no screw terminals, so as to inspect whether it can withstand mechanical stress during normal use.Specification: • Power supply: AC220V 50Hz • Test rate: 10±2r/min (GB16915.1-97: 12 ±1r/min) • Rotating radius: 100mm • Test distance: 250~500mm adjustable • Test numbers (Number of rotating): 0~999999 any set • Mass: 0.3KG, 0.4KG, 0.7KG, 0.9KG, 1.4KG, and 2.0KG (GB16915.1-97: 30N, 40N, 50N, 60N each of 2 pcs) • Stations: 2 • Dimension: 1200×1400×400 (mm) • Remarks: The mass and rotating radius can be optional as per customer requirements.
-
Product
Post Wire and Die Bond Inspection Machine
IV-E1700
-
IV-E1700 is a post wire and die bond inspection machine that is known for having a proven, effective and patented 2D+3D Inspection system. This product is best used to weed out defects with data collection for process improvement and reports for SPC quality Control.
