Prototyping Boards
-
product
Pulse Acquisition Board
MS 1818
*Used to measure the amplitude of discrete pulses driving relay coils/motors*Programmable No. of samples acquisition with programmable trigger option*Converts sine wave to square wave for pulse measurement*Measures amplitude of sine wave*16 Bit ADC interface*16 Bit data bus host interface*FPGA based design with flexible configuration*1K FIFO Storage
-
product
Digital I/O Board
3512
The 3512 is an eight channel non-isolated digital I/O board with +5V tolerant 74LCX14 inputs with hysteresis and +3.3V CMOS 74LVTH125 driven outputs. Each I/O line features a series 10 ohm damping and protection resistor and a 4.7K pull up resistor to +3.3V. On power up the outputs are tri-stated, and can then be enabled on a bit by bit basis. Output high drive is 32mA @ 2.0V minimum. Output low drive is 32mA @ 0.8V maximum.
-
product
PXI Prototyping Module, 2-Slot, 9-Pin D-Type
40-225A-702
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
6U VPX Board
VP62003
LinkedHope Intelligent Technologies Co.,Ltd.
VP62003 is a 6U VPX board based on Intel® Xeon® D-15xx processors, with more than 7-year lifecycle. Supporting up to Intel® Xeon® D-1577 (16x 1.3GHz) processor, VP62003 is able to perform vector operation and floating point arithmetic that require high throughput. Besides, VP62003 supports Intel® Turbo Boost, with the processing speed of CPU up to 2.7GHz. The high-performance CPU and the Turbo Boost technology leave no worries for extra cost and complexity of system settings.VP62003 provides 4x Rapid I/O (SRIO) x4 for VPX Data Plane communication, 2x 8 PCIe for VPX Expansion Plane communication, 4x GbE for VPX Control Plane communication, and 2x 10Gb SFP+ in front I/O for remote data transmission and communication. Rich data exchange interfaces on VP62003 make it easy to build box-level or system-level solutions.
-
-
product
Single Board Computer
VME-1909
Curtiss-Wright Defense Solutions
The VME-1909 from Curtiss-Wright Defense Solutions is designed to be a low cost, high performance technology insertion Single Board Computer (SBC). Pin-compatible with many previous generations of Curtiss-Wright SBCs, the VME-1909 offers increased computing performance with today’s latest software advances.
-
product
Digital Termination Boards
MSTB 008
For quick and secure connection of discrete wires to a Data Acquisition Processor (DAP) board, use the MSTB 008 Digital Termination Board.
-
product
Board
Arduino MKR NB 1500
Arduino MKR NB 1500 allows you to build your next smart project. Ever wanted an automated house? Or a smart garden? Well, now it’s easy with the Arduino IoT Cloud compatible boards. It means: you can connect devices, visualize data, control and share your projects from anywhere in the world. Whether you’re a beginner or a pro, we have a wide range of plans to make sure you get the features you need.
-
product
Data Acquisition Board
DAP 4200a
The DAP 4200a is an excellent choice for applications where there is a need for real-time processing of data in the time interval between samples, and for applications requiring fast sample rates. Much of the DAP 4200a design is similar to that of the DAP 3200a/415, but the DAP 4200a has a PCI host interface, and is capable of high speed data transfers to the host PC.
-
product
Breakout Boards
GrayStone offers a family of DIN rail mountable breakout boards in various connector to terminal block configurations suitable for use in automation panels, electronic diagnostics or other general electronic applications.
-
product
Rapid Prototype Development
Have time to market pressure and need to get a system or assembly or production line up and running quickly? Need to rapidly build out a solution, but don’t want to spend months on building up an architecture? Allow our rapid prototyping team to assist you – whether it is crafting 3D printed mechanical assemblies or a building up a high speed IO interface, you are in very capable hands with the ARC engineering team. Our DSX product, can help support your IP, implement your process or and be the core processing engine for your design, or if a larger system, DSX could be an integral part of your system. PVS, another tool that can help error-proof your assembly process, is ready to go in a flexible, software-centric solution that you can be reconfigured as needed to meet your changing demands.
-
product
3U VPX Board
VP32101
LinkedHope Intelligent Technologies Co.,Ltd.
Compatible with PC architecture, VP32101 is a low power-consumption 3U VPX board which supports Intel® Atom™ Bay Trail E3800 processors. Combined with up to 4GB DDR3L onboard memory and up to 64GB SATA SSD, the stability and high performance of VP32101 is best guaranteed in harsh and vibration environment.VP32101 provides rich I/O interfaces, including 2x SATA 300, 2x 1000Base-BX/T, 2x RS232/422/485, 3x USB 2.0, 1x USB 3.0, 2x CAN, 1x DP++, etc.To help users develop solutions easily and fast, LinkedHope® equips VP32101 with various BSP, including Windows, VxWorks, Linux and QNX.Apart from the traditional Air Cooling version, VP32101 provides a Conduction Cooling version to guarantee its performance in extreme environment and in an extended working temperature (from -40℃ to +70℃).
-
product
Graphics/Video Capture Board
NVP2102
The Abaco NVP2102 is a chip-down 3U XMC graphics output and video capture board based on the NVIDIA® Pascal ™ (GP107) Quadro® P2000 GPU. The NVP2102 leverages the high performance of the GPU with its 768 CUDA cores and 4GBytes of GDDR5 memory to deliver 2.3 TeraFLOPs of peak performance with CUDA™ and OpenCL™ support.
-
product
Boards
MIL-STD-1553
The MIL-STD-1553 multi function interface cards are compatible with all common variations of MIL-STD-1553 and provides a wide range of features normally found only on full size testers. The card can operate simultaneously as a Bus Controller (BC) and/or multiple (up to 32) Remote Terminals (RT), or as a Triggerable Bus Monitor. The card supports error injection and detection.
-
product
Prototyping
Is an early sample, model, or release of a product built to test a concept or process or to act as a thing to be replicated or learned from.[1] It is a term used in a variety of contexts, including semantics, design, electronics, and software programming. A prototype is generally used to evaluate a new design to enhance precision by system analysts and users.
-
product
Combination Board Tester
ATE QT2256-640 PXI
Qmax Test Technologies Pvt. Ltd.
Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or micro controller based boards. ATE QT2256-640 PXI system is designed as a combination board tester capable of testing highly complex and PCBs employing various techniques on a single platform. It can be easily upgraded to 640 digital channels and with programmable UUT power supplies, IEEE or PXI external instrumentation, Bus cycle signature system, ICE and integrated Boundary scan Test AC/DC parametric testing. The ATE is interfaced to an external host PC using a PCI express interface card allowing a maximum data transfer rate. Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or microcontroller based boards.
-
-
product
PXI I/O Board
MZ-TrigIO
The MZ Trigger I/O Board (MZTIO) is a break-out board for the Pixie-16 PXI chassis backplane providing real-time access to Pixie-16 logic signals.
-
product
Single Board Computers
SBC35-C398Q-2-0
WINSYSTEMS’ SBC35-C398Q quad-core single board computer combines high-performance multimedia graphics with a rich mix of industrial I/O. The Freescale i.MX 6Q processor’s integrated power management provides excellent efficiency and allows operation from -40° to +85°C without active cooling. It is designed for demanding graphical applications in security, transportation, medical, and digital signage.
-
product
Carrier Boards
ROM-DB7502
ROM-DB7502 is the Referenced Carrier Board designed for Advantech's Qseven 2.0/2.1 module. It i provides a thorough environment for module board evaluation with its completefunction support. It also supports 12V power input through AC/DC power adapter and with smart battery design, it's more easier for the end user to design portable devices by referring ROM-DB7502 design.
-
product
34945EXT Distribution Board, For One 87204x/206x Or 87606B Switch And Two N181x Switches
Y1152A
The Y1150A-Y1155A distribution boards enable simple connections to the external switches. The distribution boards plug onto the 34945EXT and are used to route the power and control signals from the driver module to the switches using standard cables.
-
product
PC/104 OneBank Board
EMC²-7K325
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-7K325 to be added to robust and rugged installations for various commercial, medial, industrial and military uses and to enable more versatility the EMC²-Kintex7T also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options
-
product
Quad IF Board
DP-VME-1242
DP-VME-1242 is VME64x, 6U single-slot solution for high sampling rate and down conversion applications. Applications include - IF signal processing, radar systems, communication systems, and GPS systems.
-
product
Timing Board #1
TIO-10 #1
Interface board for converting signals on a National Instruments PC-TIO-10 timing board to and from fiber optic signals. Bursts, delayed pulses, and frequencies can be generated on outputs. The input channel can be used to measure frequency or period.
-
product
13MP Camera Board For I.MX8
E-CAM130_iMX8
e-CAM130_iMX8 is a 13MP 4-lane MIPI CSI-2 autofocus color camera board for iMX8 family of processors. The e-CAM130_iMX8 camera board is interfaced directly to the CSI-2 MIPI interface on the Variscite's DART-MX8M/DART-MX8M-MINI Evaluation kit (VAR-DT8McustomBoard). The iHDR (interlaced High Dynamic Range) support helps to capture good quality images in both high and low illumination. e-CAM130_iMX8 also comes with a high-performance Image Signal Processor (ISP) that performs all the Auto functions (autofocus, auto white balance, auto exposure control). Customer who wants to integrate this camera into their end product can directly purchase e-CAM130_MI1335_MOD camera module.
-
product
Combination Board Testers
QT2256-640 PXI
Qmax Test Technologies Pvt. Ltd.
designed as a Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform. It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities for conventional PCBs.
-
product
Power-off Circuit Board Testing
Huntron® Trackers®
Adding diagnostic tools to enhance your circuit board test capabilities is an important part of any electronic repair environment.Huntron Tracker power-off circuit board test uses analog signature analysis to detect and isolate component faults on boards beyond power-on functional testing. By comparing Tracker signatures from a working circuit board to the signatures of a non-working board, you can troubleshoot down to the component level.
-
product
34945A Distribution Board, With Generic Screw Terminals For Driving 16 Switch Coils
Y1155A
The Y1150A-Y1155A distribution boards enable simple connections to the external switches. The distribution boards plug onto the 34945EXT and are used to route the power and control signals from the driver module to the switches using standard cables.
-
product
FMC-HPC ADC Board
FMC123
Sundance Multiprocessor Technology Ltd.
The FMC123 provides four 16-bit A/D channels up to 1Gsps. The design is based on Texas Instruments’ ADS54J60 Analog-to-Digital converter. The sample clock can be supplied externally through a coaxial connection or supplied by an internal clock source (optionally locked to an external reference) for multi-channel synchronization. An external trigger input is available for timing synchronization. The FMC123 is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
product
PCI Express To CPCI Board
MS 1719
PCI Express to CPCI card is used to extend PCI / PCI-X bus from one PCI system to another system over an optical fiber medium up to 500meters or over a copper medium up to 7 meters using a PCI express interface. This card receives/transmit cPCI signals from/to the Host System. These cPCI signals are converted into PCI Express using cPCI / PCI-x to PCI Express cross bridge and vice versa. The PCI Express signal is transmitted / received through the optical interface or copper interface.
