Proto Boards
-
Product
Temperature Measurement click board
Thermo J click
-
Thermo J click is a temperature measurement click board™, which uses a thermocouple type-J probe, connected to a PPC-SMP-J onboard connector. The active part of the Thermo J click is MCP9600 by Microchip - a thermocouple EMF to temperature converter, with 1.5°C of maximum accuracy. The onboard PCC-SMP-J connector ensures the secure connection and accurate readings for the connected thermocouple.
-
Product
3U CPCI ARINC 429 Board
MS 1725
-
- Bus Interface:- 32 Bit PCI Bus with 3 U Form factor- PCI to PCI Bridge Interface- Speed of operation up to 66MHz- 8 ARINC 429 TX and 16 ARINC 429 RX channels- 4 RS422 Channels- 16 TTL I/O Channels- Message Storage Buffer- Driver interface for Windows2000/XP/VISTA and LINUX OS- Self Test future
-
Product
Serial I/O Boards
-
Serial Mode Protocols include Asynchronous, Bisync, SDLC, HDLC, IEEE 802.3, Synchronous Telemetry, Simple Clock/Data ("-SYNC" product line), Di-phase and SPI Interface. Transceiver support RS485, RS422 (V.10), RS232 (V.28), RS423, V.35, RS530, as well as other software selectable mixed protocol modes Up to Eight Independent Serial Channels per Board Synchronous Serial Data Rates up to 10 Mbits/sec Asynchronous Serial Data Rates up to 1 Mbits/sec PMC and cPCI rear I/O support Custom Protocols Available
-
Product
MicroSemi-SiC-Module / Evaluation Board
EV-MS4135PL1Z-U1 Pre-Release
-
High power evaluation board, up to 1200V & 50A @ 200kHz switching frequency featuring the combo ADI ADuM4135 isolated gate driver + LT3999 isolated power supply controller + Microsemi SiC power module in half bridge configuration.
-
Product
DAQ- Data Aquisition Boards
ETS Series
-
The ETS Series products are designed to create a simple "Go, NoGo" test platform that executes quickly and requires minimal Operator interaction. Low-cost alternative to traditional PC-based test equipment. Test Electronics sources and stocks a large variety of data acquisition and sensor boards to make your hardware build quick and easy. Develop your own embedded test system or use the embedded test systems we have developed.
-
Product
12-bit, 100KHz, 16SE/8DIFF Isolated Analog Input Board
APCI-3001-16
-
16 single-ended or 8 differential inputs 12-bit resolution Optical isolation 500 V 100 kHz data transfer rate Automatic analog acquisition 8 digital I/O, 24 V, isolated, timer Trigger functions Graphical display of the measured data
-
Product
Motion Control Terminal Board for Panasonic MINAS A4 Servo Amplifiers
DIN-814P-A40
-
This well-designed motion control terminal board is for the users who use Panasonic MINAS A4 super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
Product
CPCI-S.0 Standard Compliant Peripheral Board Controlled by a PCIe Channel Derived from the Backplane Connector P1
MIC-3820
-
MIC-3820 is a 2.5" on board SSD/HDD carrier board running at SATA Gen3 speed. A fast swap of the drive can be accomplished via a reserved thumb screw to help open a door on the front panel and eject the drive. The excellent mechanical design makes it easy to replace modules.
-
Product
16 Relay Output PCIe Board, 8 Isolated Digital Input Channels, 24V
APCIE-2200-16-8
-
8 electromechanical relays with change-over contacts The PCI-Express 16 relay board APCIe-2200-16-8 has 16 relay output channels and 8 isolated digital inputs, 24 V. 7 inputs are interruptible. The board is especially suited for applications like industrial I/O control, signal switching, alarm monitoring, as interface to machines, for the ON/OFF monitoring of motors, lights etc. in the harsh industrial environment.
-
Product
PXI Express Optical FPGA Board
HSS-8324
-
The Conduant HSS-8324 Optical FPGA board provides the user with a hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PXI Express (PXIe) interface and its 24-lane optical interface. The PXIe interface provides a theoretical maximum throughput of 8GB/s (simultaneous in and out).
-
Product
Carrier Boards
ROM-DB3900
-
ROM-DB3900 is an evaluation carrier board designed for the Advantech RTX2.0 module. It is compatible with the RTX2.0 module ROM-3420 and has a rich I/O interface for evaluation and development. It supports wide range operating temperature, and also supports two MIPI connectors for a camera module. ROM-DB3900 is an ideal development board for ruggedized applications, such as industrial control, automation control and HDMI systems.
-
Product
6U VPX Ethernet + SRIO Switch Board
VP68803
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP68803 is 6U VPX Ethernet + SRIO switch board compliant with VITA46 and VITA65 specifications, and is mainly applied for high-speed data exchange and routing between different boards in a VPX chassis. Designed with 6U VPX form factor, VP68803 has excellent performance in thermal dissipation and environment protection.Integrated with Ethernet, SRIO switching and routing, VP68803 has 20 1000Base-BX Ethernet interfaces for control plane, and has 19 x4 SRIO 2.1 ports for data exchange. Therefore, VP68803 realizes internal and external data transmission with comprehensive integration. Besides, VP68803 can be installed in Single-Star Topology and Dual-Star Topology backplanes. These characteristics guarantee the stability and applicability of VP68803.
-
Product
Overhead Board
OVH-380-2
-
Curtiss-Wright Defense Solutions
The OVH-380-2 is the enhanced overhead board for the AIM/ HS-AVDAU-200XE. It stores and executes the operating system, application software and drivers, and terminates the IP stack for Ethernet support. It also receives and formats inbound (acquired) data.
-
Product
Electronical Load Board 3U CompactPCI (conduction cooled)
046-712
-
The 3U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
Product
PCI Express Multi-Function Boards
PEX-1002L
-
PCI Express, 32-ch, 12-bit, 110 kS/s Low Gain Multi-function DAQ Board. Includes CA-4002 D-Sub connector
-
Product
3U CPCI CPU Boards
-
Advantech 3U CPCI boards are Intel based CPU blades that support single or dual processors that fully utilize I/O features of Intel® chipsets.
-
Product
Mini-ITX Embedded Board with 8th/9th Gen Intel® Core™ i7/i5/i3 Processors
AmITX-CF-I
-
The AmITX-CF-I is a Mini-ITX motherboard supporting the 8th/9th Gen Intel® Core™ i9/i7/i5/i3, Pentium® and Celeron® processor in the LGA1151 package, and the Intel Q370/H310 chipset. The AmITX-CF-I is specifically designed for customers who need high-level processing and graphics performance with a long product life solution. This model supports ubiquitous high-speed data transfer interfaces PCIe 3.0, USB 3.1 Gen2 and SATA 6 Gb/s (SATA III), with dual-channel DDR4 2400/2666 MHz non-ECC memory up to 32 GB in two SODIMM slots. The AmITX-CF-I features DVI, DP and HDMI ports, LVDS header, dual Gigabit Ethernet ports, USB 3.0 ports, USB 2.0 ports, SATA 6 Gb/s ports, and audio with Line-out, Line-in and Mic-in connectors. Expansion is provided by one PCIe x16, one M.2, and one mini-PCIe slot. The onboard pin header provides GPIO, USB and RS-232 support. The board is equipped with SPI AMI EFI BIOS, supporting embedded features such as hardware monitor and watchdog timer.
-
Product
RTM Discrete Signal Conditioning Board
MS 3632I
-
CPCI Rear IO Discrete Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advance Compute & IO Module (MS3639i). This board primarily focusing on signal conditioning of TTL/CMOS DIO levels to required type of discrete input and output interface. Digital IO from ACIO board to discrete IO at Rear IO interface. Board takes 144 DIO from ACIO and does Open/Ground, 28V/Open, 28V/Ground configuration. In addition it shall generate additional 32 discrete input / output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector.
-
Product
3U CompactPCI Serial Power Interface Board
046-201
-
Standalone Power-BP 3U 8HP to connect CPCI Serial power supplies to compactPCI Serial-BPs. The connection is made via cables.
-
Product
PCIe I/O & Comm Board
79C3
-
NAI’s 79C3 is a PCIe Multifunction I/O and Communication Board with three independent function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
Digital Backplane Interface Board
MSXB 033
-
The Microstar Laboratories Digital Backplane Interface Board, part number MSXB 033, interfaces the Digital Backplane with a Data Acquisition Processor. The Digital Backplane Interface Board must be installed in the Digital Backplane to connect the backplane to a Data Acquisition Processor.
-
Product
16-CH Discrete Input 16-CH Discrete Output Daughter Board Module
HSL-DI16DO16-DB-NN
-
- Slave ID consumption: 1 16-CH NPN sinking type sensor inputs or dry contact and 16-CH - NPN sinking type outputs- Photo couple isolation voltage: 2500Vrms- Input impedance: 4.7KΩ- Input current: ??10mA(Max), ??12.5mA(Peak)- Input voltage: ??40V (Max)- Output switching capacity:300mA/ch at 24VDC- Terminal Base:HSL-TB64 or HSL-TB32-DIN- LED indicator: Power, Link and I/O status
-
Product
GPIB Serial Interface Boards
-
ICS's GPIB to Serial Interface boards are designed for in-chassis applications. Select boards with transparent data transfer or boards with smart firmware that can add an IEEE-488.2 interface to any serial device
-
Product
Intelligent Double Sized H009 Interface Module for Excalibur 8000 Family of Carrier Boards
M8KH009
-
The M8KH009 is an intelligent, double-sized, H009 interface module for the multimode, multiprotocol, EXC-8000 family of carrier boards. The M8KH009 provides a complete solution for developing and testing H009 interfaces and performing system simulation of the H009 bus, according to the standard H009 protocol. Each module of the M8KH009 contains 32K x 16 dualport RAM for Data Blocks, control registers, and Look-up tables. In addition, the module contains another 32K x 16 dual-port RAM for a Concurrent Monitor. All data blocks and control registers are memory mapped, and may be accessed in real-time. Each of the independent, dual-redundant M8KH009 modules may be programmed to operate in one of three modes of operation: Central Control Complex (CCC) mode with Concurrent Peripheral Unit operation (1–16 PUs), Peripheral Unit mode (Multiple – up to 16 PUs) and Bus Monitor mode. In addition, the module can simultaneously operate as an independent Internal Concurrent Monitor in CCC, Multiple PU or CCC/Concurrent PU modes.
-
Product
Board Test Adaptor (BTA)
MS 1104
-
BTA is used to test and validate TARANG (RWR) boards. The BTA has PC interface through RS232 / USB communication port. GUI based Test Software is used to test the UUTs and displays the result.
-
Product
Digital I/O Board
P104-DIO-96
-
Each I/O line of this card is buffered and capable of sourcing 32mA, or sinking 64mA. The board simulates Programmable Peripheral Interface chips (PPI) to provide a computer interface to digital I/O lines. Each PPI supports two 8-bit ports (A, B) and two 4-bit ports (Chi, Clow). Each port can be configured to function as either input or output latches. The I/O line buffers (types 74ABT240 and 74ABT245) are configured automatically by hardware logic for input or output according to the PPI Control Register direction software assignment.
-
Product
ISA Data Acquisition Boards
A-812PG
-
A-812PG is a 12-bit multifunction analog and digital I/O board for PC/AT compatible computers. A-812PG offers 16 single-ended plus two channels of analog output with 12-bit resolution. A-812PG has 16 digital inputs, 16 digital outputs, and one timer/counter channel. A-812PG Provides gains of 1, 2, 4, 8, and 16. It has a maximum sampling rate of 62.5K samples/s. DMA operation is jumper selectable for levels 1 or 3. Interrupts are jumper selectable between 3 and 15.
-
Product
6U cPCI Multi-function I/O Boards
78C2
-
NAI’s 78C2 is a 6U cPCI Multifunction I/O and Communication Board with six independent function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
GPGPU Board
GRA115Q
-
The GRA115Q is a rugged 3U VPX graphics output and high-performance computing GPGPU board based on the NVIDIA Turing™ architecture. It is an ideal solution for graphics/display processing applications such as situational awareness, and moving map applications as well as general purpose graphics processing unit (GPGPU) applications such as radar and video surveillance/analysis.
-
Product
2U Short-Depth Optimized Chassis For ASMB-62 Series Edge Server Board For Edge Computing.
HPC-6240
-
Supports ASMB-62 edge series motherboardFour 2.5" hot-swappable SATA drive bays (2 NVMe drives in option)Four FH/10.5"L and four FH/HL expansion slots1200W 1+1 redundant power supply with 80 Plus platinum level certificateUltra Slim ODD support in option2U Front Bezel in option
