High Voltage Transformers
See Also: Substation
-
Product
High density PCB connectors
MHD/MDD/MDP Series
-
Smiths Interconnect's MHD/MDD/MDP series is an ESA qualified, high density board to board and board to wire interconnect available in up to 400 positions, with available insulators to accommodate coax and power contacts.
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-113
Precision Resistor Module
The 40-297A-113 (PXI) and the 42-297A-113 (PXIe) are 9-channel programmable resistors with a range of 1 Ω to 238 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI/PXIe High Voltage Power Relay Module, 14xSPST With Hardware Interlock
40-323-901-HI
Relay
The 40-323-901 (PXI) and 42-323-901 (PXIe) are 14xSPST relay modules suitable for applications requiring high voltage power switching with high density. They have current handling up to 0.25 A, cold switching up to 9 kVDC/9 kVAC peak and hot switching up to 7.5 kVDC/7.5 kVAC peak.
-
Product
High Frequency Chambers
-
Specialized, shielded rooms designed to absorb electromagnetic reflections.
-
Product
High Purity Germanium (HPGe) Radiation Detectors
-
Semiconductor based photon radiation detectors have been evolving for over half a century, with ORTEC pioneering commercial availability for a majority of that time. Initial offerings were based around lithium-drifted germanium Ge(Li) and lithium-drifted silicon Si(Li). Ge(Li) was later replaced with more advanced, high purity germanium (HPGe) detectors. ORTEC provides a comprehensive suite of HPGe detector solutions covering an extensive range of energies and for a variety of applications.
-
Product
Fourier Transform Infrared Spectrophotometer
IRSpirit
-
Despite their small footprint, smaller than an A3 size sheet of paper (297 x 420 mm), these models have been engineered with a wide sample compartment that accommodates existing accessories from Shimadzu and other manufacturers. This capability makes them the smallest (installation footprint) and lightest FTIR spectrophotometers in the world that can be used with optional products from other manufacturers. They also include a program, IR Pilot, with 23 application-specific workflows that can be utilized without involving any complicated parameter setup process. Customers can select from either the IRSpirit-T model, which offers sensitivity equivalent to standard Shimadzu models, or the reasonably priced IRSpirit-L model.
-
Product
High Precision Compression Type Load Cell
HR II
-
A high-precision compression-type load cell is a sensor that accurately measures compressive (pushing) forces, designed for applications requiring very tight accuracy and reliability. It works by converting a downward force into an electrical signal, often using strain gauges to measure deformation, and is used in demanding fields like calibration, manufacturing, and medical equipment.
-
Product
High Temperature Anemometer
6162 Series
-
The Model 6162 is a unique anemometer designed for specialized high-temperature testing.
-
Product
High Power LED Test System
Lumere-GM
-
Evolusys Technologies Sdn. Bhd.
Lumere GM is a LED test and measurement system for various parameters of LED light. It is a high-accuracy system with a temperature-controlled CCD, its geometry conforms with CIE-Publication 127, and the test program is easy to configure and adjust. The Lumere GM is used in laboratory applications and in the production of high-power LEDs.
-
Product
High Performance VXI Chassis for Military ATE Systems
1261B Series
Chassis
The 1261B high-performance VXI chassis serves as the standard for most military ATE systems. All 1261B chassis include full-power protection features such as overvoltage and overcurrent protection, and also incorporate a quick-check diagnostic connector to verify performance of power supply voltages, currents and specific VXI signals.
-
Product
Ultra High 2.84 (81.00) - 10.00 (283.00) High Performance Bias Ball Probe
POGO-1I-10
ICT/FCT Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
High Accuracy In-Situ Mass Flow Verifier
HA-MFV
-
The HA-MFV, High Accuracy Mass Flow Verifier is designed for use on process tools to verify mass flow control flow rates in-situ. Available with EtherCAT® or DeviceNet™ communications and measurement accuracy of 1.0% of reading, the HA-MFV can verify MFC flow with the actual process gas significantly better than older rate-of-rise devices or process chamber rate-of rise methods.
-
Product
High Speed End Launch Connectors
-
Fairview Microwave’s high-speed end launch connectors are comprised of four models that provide VSWR as low as 1.10:1 and a maximum operating frequency of 40 to 110 GHz, depending on the model. These end launch connectors are reusable, don’t require any soldering and have a compact profile with a 0.350-inch mounting width and a 0.005-inch launch pin. They feature an outer conductor made of stainless steel and a gold-plated beryllium copper center contact.
-
Product
High Flexibility Test Controller Card
TCC 1800-UE
-
The TCC1800-UE Test Controller Card is a generic control board for production testing of printed circuit boards (PCBs). The board is controlled by a command language on a PC to which it is connected via Ethernet.The TCC1800-UE is designed to work with positive voltages up to 24V. The card provides extensive IO: Analog and digital interfacing, counters, PWM outputs, bidirectional I/O, ethernet-, CAN, USB, SPI and I2C interfacing.
-
Product
Laser Diode Light Current Voltage (LIV) Test Instruments
-
The Yelo LIV test instrument allows LIV measurements to be taken from laser devices loaded into a Yelo module. This module can also be used with the Yelo Y1000L Low Power Burn-in system. The LIV test instrument has been designed for easy operation. Once powered on, and with laser supply enabled, the touch screen can be used to initiate, monitor and review measurements of laser devices.
-
Product
Standard Voltage 37 Pin D-Type Connector Blocks
-
The connector blocks and breakouts below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
High Volume / Double-Side Applications
APS 80D
-
Simultaneous, double-sided probing of up to 8" wafersPowerful, user-friendly control and monitoring softwarePlanarization of needle sets and constant preset needle loadPattern recognition systemRobot handling systemConfigurable to voltages in excess of 5 kV for specialized applications
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-051-HI
Programmable Resistor Module
The 40-230-051-HI (PXI) and 42-230-051-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 2.95MΩ with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Additional Products: High Voltage 37 Pin D-Type Cables - Connector to Connector
-
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Ultra High 3.83 (109.00) - 10.00 (283.00) High Performance Lead Free Probe
LFRE-72H-10
ICT/FCT Probe
Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,700Overall Length (mm): 43.18
-
Product
High Speed Machinery Test Rigs
-
designs and builds all kinds of rigs for testing the components of high speed machinery. As in our spin pits, BSi's unsurpassed ability to generate and precisely control extraordinarily high speeds is the key competitive advantage. BSi engineers also draw on our vast experience to provide reliable drives and rigs to meet the most demanding requirements under the most extreme conditions. We have engineered and manufactured rigs for testing bearings at speeds to 250,000 rpm. We have delivered test benches for testing abradable seals at temperatures to 1100 deg. C.
-
Product
Low Voltage High Current DC Electronic Load
N62400 Series
-
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N62400 series is developed based on NGI's years of experience in testing for fuel cell. It is with high accuracy, high reliability and high cost-effective. N62400 series is with high power density and elegant appearance, which is available for benchtop use or installation in 19 inch cabinet.
-
Product
Closed-loop Ionizer Controllers For Multichannel Voltage Detection
Novx 3352/3362
-
Simco-Ion’s Novx brand of Passive (Model 3352) and Active (Model 3362) Multi-fan Closed-loop Ionizer Controllers provide the capability to simultaneously detect, measure, record and monitor electrostatic voltages in multiple locations. The versatile antennas used with these systems allow their use in a variety of applications including monitoring sensitive workstations, in-tool voltages, or ionizer performance with the option of closed-loop control to select ionizer products.
-
Product
Programmable Voltage Reference Plug-In
ProDAQ 3202
-
The ProDAQ 3202 voltage reference card is used in the ProDAQ 3180 ultra-performance motherboards and LXI function card carriers. The ProDAQ 3202 voltage reference card is plugged directly onto the motherboard or carrier and can distribute the reference voltage to all ProDAQ function cards via two signal lines. This allows the distribution as a differential signal to overcome possible noise pick-up.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-223-HI
Programmable Resistor Module
The 40-230-223-HI (PXI) and 42-230-223-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 3Ω and 3.55kΩ with 1Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
AC /DC Withstand Voltage Tester 5KV/100mA
2672C
-
Shenzhen Chuangxin Instruments Co., Ltd.
*High voltage, large current, high accuracy.*Leakage current, testing time, continuous arbitrarily, well-adapted.*Synchronized display measuring value( time, voltage and current).*Can choose manual or remote control test*High voltage breakdown protection, sound and light alarm, safe and reliable *Easy operation, suitable for use in production line*DC output can test small capacitance, high-voltage silicon stack, reverse voltage of transistors
-
Product
PXI High Voltage Power Multiplexer, Octal 3:1 (SP3T)
40-331A-005
Multiplexer Module
The 40-331A-005 octal 3:1 MUX is part of our range of 40-331A/332 High Voltage Power Multiplexer and Matrix Modules and is suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching.
-
Product
2 Channels, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTB
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
Standard Voltage 9-Pin D-Type Connector & Cable Accessories
-
The Standard Voltage 9-Pin D-Type connector is used on PXI switching products to provide a low density connector solution. Connection solutions for modules with High Voltage Rating D-Type connectors are also available.
-
Product
Voltage Pulse Generator
LSG-65C
-
Shanghai Sanki Electronic Industries Co., Ltd.
The waveform parameters of the voltage pulse generator LSG-65C fully meet the requirements of IEC60065 and GB8898; the pulse voltage output of up to 10kV can meet the requirements of different test levels of users; the self-developed high-voltage electronic switch is adopted , which has high stability, low noise and long service life. Long; digital display mode, intuitive and easy to operate.
