Benchtop Chambers
See Also: Bench, Test Benches, Bench Multimeters
-
Product
Process Sense™ NDIR End Point Detector For Chamber Clean
-
The Process Sense endpoint sensor is a small, low-cost SiF4 sensor specifically designed for Remote Plasma Chamber Clean Endpoint detection for silicon-based CVD deposition chambers. Process Sense is based on infrared absorption, the only technique applicable to all plasma cleaning processes (in-situ and remote). It gets mounted onto a bypass on the rough line, ensuring no effect on deposition hardware. The signal level reported by the Process Sense, which is proportional to SiF4 concentration, can be used to determine the completion of the chamber clean process.
-
Product
Environmental Chambers
KB Series
-
Darwin Chambers KB series Environmental Chambers are a top selling unit. It is quiet, easy to clean, highly reliable and ideal for laboratory use. Our environmental chamber offers hot gas bypass control of refrigeration and resistive heat to facilitate reliable, critical temperature and humidity control. All KB series environmental testing chamber models are designed to have a temperature range of 4-60o Celsius. Temperatures greater than 60o Celsius or lower than 4o Celsius can be achieved with optional upgrades to construction and components. All KB series environmental chambers come standard with Fuji’s PXG4 microprocessor, but we often install Watlow brand microprocessors for customers that need that brand or the capabilities it has. Unlike many proprietary controllers on the market, these controllers are available off the shelf and have been proven in tens of thousands of installations. All necessary functions are included in our Features section below. Many additional options are available both regarding control and recording of data (chart recorders and loggers)
-
Product
Sand and Dust Chamber
-
Designed to test a product’s resistance to extremely dusty, desert-like environments, Thermotron’s D-27 Sand and Dust Chamber provides the capability of meeting specific automotive test standards. Powerful blowers intermittently blow compressed air up through finely powdered dust and then allow the dust to settle back down covering the product.
-
Product
Vibration Chambers
ETV-SERIES
-
Environmental Chamber with Vibration Shaker Interface provision consists of Environmental Test Chamber, Vibration Shaker Interface Provision, HMI/PC PLC based Control System etc., This chamber is designed with unique features to meet the control parameters like Temperature, Humidity (optional) and 3 Axis Vibration Controls which are specified in the specification.
-
Product
Test Chambers
-
Associated Environmental Systems
Associated Environmental Systems (AES) designs and manufactures standard and customized environmental test chambers. Our products vary in size from small bench top test chambers to very large walk-in environmental rooms. Whether you are looking for off-the-shelf or unique test chamber solution, we can meet your needs.
-
Product
Drive-In Chambers
-
Environmental testing of automobiles requires additional consideration of the facility where the chamber will be installed, and its planned use. Test methods for vehicles can include additional conditions besides temperature and humidity in an attempt to simulate real-world conditions.
-
Product
Environmental Test Chambers
ET-Series
-
Environmental Test Chambers are designed with uncompromised features included in the system to meet your changing application needs of simulation of wide range of temperature, relative humidity etc., conditions without the added cost of expensive add-on’s as options. Available in varied volumes to fit your differing specimen sizes
-
Product
Hydrostatic Test Chambers
-
Test chambers are available to protect personnel during proof or burst testing. A few samples are pictured below. Chambers are manufactured in polished stainless steel with a clear polycarbonate door(s) for visibility during testing. Fluid port(s) are provided inside the enclosure, while all controls remain outside the enclosure for operator safety. In a hurry? Choose from our selection of Quick Ship Test Systems. basic units can ship within 24 hours or less and chamber systems within 2-3 days. we normally stock test chambers with nominal working area dimensions of either 24" wide x 24" deep x 15" high, 36" x 36" x 15", 48" x 24" x 15" or 72" x 24" x 12" with the door opening from the top. specify individual parameters at our customization page. Need a different size or configuration? No problem, simply specify dimensions and features that more accurately meet your particular requirements and we will be pleased to accommodate you. To customize a system to fit your particular application, please visit our customization page or give us a call at (916) 645-3317.
-
Product
IPX56 Simulation Rain Test Chamber
CX-IPX56A
-
Shenzhen Chuangxin Instruments Co., Ltd.
IPX56 Simulation Rain Test Chamber widely used in the lamps and electrical and electronic product certification testing institutions and for testing the waterproof of electrical and electronic products of shell protection level.
-
Product
Thermal Shock Chamber
ETS-Series
-
air-to-air and liquid-to-liquid Thermal Shock Chambers from Envisys are available in different volumes to suit the varied testing needs. Horizontal or vertical models consisting of cold and hot zones with product carrier basket of sizes 50, 100, 150, 300, 600 and 900 litres which transfers the specimen under test between cold and hot zones using electro pneumatic / motorized basket movement.
-
Product
Benchtop Temperature And Humidity Environmental Test chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Benchtop Temperature and Humidity Test Chamber provides a compact footprint and multi-function test performance. It is very popular for labs and product manufacturers to test various small electronic product, electronic components and materials with simulating temperature and humidity environment condition.
-
Product
Climate Test Chambers
-
Infinity Machine International Inc.
Climate Test Chambers by Infinity Machine International Inc. - for applications such as dust proof climate test chamber for lighting, dust climate chamber for lab, and more.
-
Product
2 Zone Thermal Shock Test Chamber
-
2-Zone Thermal Shock Testing Equipment with programmable electronics.
-
Product
RF Chamber Fixtures
-
- 12” W x 12” D x 8” H internal dimensions- RF mechanical chamber can fit various wireless and Bluetooth products- test either commercial or consumer
-
Product
Antenna Test Chamber for Automotive Radar
ATS1500C
-
The R&S®ATS1500C radar test chamber is a compact antenna test range (CATR), consisting of a gold-plated parabolic reflector and a two-axis positioner for 3D movements of the radar module. Combined with the R&S®AREG800A target simulator and other Rohde & Schwarz test and measuring instruments, it can be used for a variety of applications, including antenna characterization, module calibration, RF performance validation, interference testing or in-band compliance testing. The chamber is equipped with a universal feed antenna which gives access to both polarizations in parallel. Automated temperature testing over the range of -40 to 85°C is possible with an optional enclosure.
-
Product
Electromagnetic anechoic box/Shield box/Anechoic chamber
-
The necessity of a wireless system test has risen by the spread of recent wireless telecommunication equipment as shown in cellular phone, wireless LAN, RF-ID tag and ETC (Electronic Toll Collection system). It is necessary for a wireless test to be performed in anechoic environment in which an external noise is intercepted and a radio wave does not reflect internally. An anechoic chamber (room version of a shield box) is proper facilities but needs a wide space and a huge cost. Especially, the equipment under wireless system test on the production line can not radiate any signal radio wave outside before approval. The shield box satisfies these conditions.
-
Product
TSE-12-A Thermal Shock Chamber
-
Did you think that getting a thermal shock chamber was too expensive, required special utilities, and half your lab-space? The TSE-12 thermal shock chamber is the solution. Only 26 inches wide, the TSE-12 transfers product loads between cold and hot zones with a temperature range of -65°C to 200°C.
-
Product
Battery Test Chamber
-
Thermotron Battery Test Chambers are manufactured to thoroughly test battery cells and lithium-ion battery packs. Diverse chamber sizes and types allow for a variety of battery types to be tested. Thermotron offers a variety of features to ensure the safety of the battery test chamber users while testing batteries. These features reduce the chance of an explosion and minimize the damaging effects of a spark-induced explosion.
-
Product
Digital Acquisition Benchtop System
-
Reliable and repeatable switching is critical for your measurement accuracy whether you use switching to route signals for design verification applications or for complex automated functional test systems. Keysight's switch measure mainframe and modules help ensure confidence in your measurement results.
-
Product
Ozone Aging Test Chamber
-
This product series are mainly used to evaluate the ozone aging resisting performance of rubber and the protective efficacy of the antiozonant so as to take the effective ozone-aging resisting measures to extend the life span of the rubber products.
-
Product
Programmable Benchtop DC Power Supply
62000L
-
Chroma Systems Solutions, Inc.
Provides high quality yet cost effective programmable benchtop DC power, designed to meet the stringent requirements of the next generation of power electronics.
-
Product
Walk in Chamber for Altitude Simulated Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
Walk in Chamber for Altitude Simulated Test Relative Standard test requirementsTest Object: battery pack and systemTest Conditions: Altitude 4000m or the equate air pressure condition, atroom temperature.The test objects stay in the test condition as Item 2 for 5 hours.Subject the test object to 1C(no more than 400A) constant current discharge until reaching the cutoff condition.After testing, observe for 2h under the room temperature.
-
Product
Salt Water Spray Test Chamber
CX-H60L
-
Shenzhen Chuangxin Instruments Co., Ltd.
The salt water Spray Tester is used to create and maintain the salt spray (fog) test environment, and test the anti-corrosion quality of the materials surfaces, and is suitable for researching materials, light industry, electronic, instrumentation and other industries etc.
-
Product
IPX9K Rain Spray Testing Chamber / Rain Resistant Test Machine
CX-IP9K
-
Shenzhen Chuangxin Instruments Co., Ltd.
Water Spray Test Equipment is used to test the water resistance; which is mainly for electronic and electrical products. It can also provide references for product design and quality control.
-
Product
Modular Walkin Chamber
-
CME’s Modular Walk-In chamber offers unmatchable flexibility in installation. The panelised construction is engineered to perform at demanding testing conditions offering highest reliability and performance. Besides modular construction, we also offer Walk-In chamber made from welded rigid panels.
-
Product
Benchtop Digital Multimeters
-
Measure DC voltage and temperature simultaneously 7-1/2 digit resolution 1-year 9ppm Accuracy Built-in EXT I/O, LAN, and USB
-
Product
Benchtop Water Hardness Meter
LD-LBWM-A10
-
Benchtop Water hardness meterLD-LBWM-A10is equipped with large backlit LCD display, 2 to 5 points calibration with low to high concentration range. The calibration due reminder alerts user for calibration of the meter on regular basis. The System menu allows setting the 7 parameters like stability condition, auto-power off etc. It measure salts of calcium & other elements at mg/L, mmol/ scale which causes hardness water.
-
Product
Laboratory Battery Tester With Integrated Chamber
-
Compact and versatile, our portable desktop solution integrates Arbin's advanced testing features.
-
Product
Rain Spray Test Environmental Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s rain spray test environmental chamber is also known as rain spray test chamber, it is used to test the water resistance for electronic and electrical products, such as solar lights, garden lights, buried lights, tunnel lights, car lights, fountain lights, the display…etc. It can also provide references for product design and quality control.
-
Product
Walk in chamber for Complex Salt Spray Test (Temperature controllable)
-
Guangdong Bell Experiment Equipment Co.,Ltd
Walk in chamber for Complex Salt Spray Test Relevant standards requirement1. Test Object: battery pack andsystem.2. Refer GB/T4 part 5.5.2 test method, test according to GT/T2423.17 test conditions.3. The salt solution was made up with sodium chloride (chemically pure and analytically pure) and distilled or deionized water，Its concentration is (5 + 1)% (mass fraction).4. (35 ± 2) ℃, the measured pH value is between 6.5-7.2.5. Placed the test objects in the salt spray chamber for cycling test. Each cycling duration for 24h. Spray salt solution to the test object for 8 hours under the temperature of (35± 2) ℃ , remain for 16 hours. Between the forth and the fifth hour in one cycles should be according to test requirement in GB/T 28046.1-2011, test mode with 3.2.6. Total 6 cycles testing.7. Salt spray test is not necessary for the test objects being installed in passenger, luggage or cargo compartments.
