Impulse Voltage Generators
-
Product
Resets And Voltage Detectors
-
ST’s reset and voltage detector ICs provide basic voltage monitoring (low-voltage detect POR-LVD function) and reset timing for power-on resets. These devices offer:
-
Product
Standard 1.55 (44.00) - 3.20 (91.00) General Purpose Probe
HPA-50U
General Purpose Probe
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 50Full Travel (mm): 1.27Recommended Travel (mil): 50Recommended Travel (mm): 1.27Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 590Overall Length (mm): 14.99
-
Product
Signal Generator
-
bsw TestSystems & Consulting AG
Especially for signal generation above 50GHz and in waveguide bands is done with a standard lower microwave generator and then the signal is frequency multiplied to get to higher frequencies. The frequency multiplied signal may optionally be filtered to make it spectrally pure and/or amplified to come to an appreciable signal level.
-
Product
Lock-In Voltage Preamplifier
SR550
-
Stanford Research Systems, Inc.
The SR550 Voltage Preamplifier is designed to work with any SRS lock-in amplifier. Preamplifiers provide gain close to the experimental detector, before the signal-to-noise ratio is permanently degraded by cable capacitance and pickup
-
Product
Thermal Voltage Converter
1395D
-
The 1395D series of TVC's, have Dual Thermal Element technology. The 1395D offers double the output voltage (typically 14 mV instead of 7 mV). This higher output voltage means better resolution and increased accuracy. It can be used to measure AC Voltages between 20 Hz and 100 MHz and it can serve as a primary AC voltage standard and/or standard for calibration of AC calibrators and voltmeters.
-
Product
Voltage Testers
DUSPOL
-
BENNING Elektrotechnik und Elektronik GmbH
phase-sequence test (counter-clockwise / clockwise)single-pole phase test: " symbol (red LED)measuring point illuminationacoustic and optical continuity testfrequency measurement 1 1000 Hzvoltage indication 1 1000 V AC TRUE RMS / 1200 V DCresistance measurement and diode test with conducting-state voltage indicationlc display with background lightingsensor of non-contact cable break detectorload connection via large-scale push buttonsvibrating alert in the test handleshock-resistant housing with protection against dust and water jets (protection class IP 65) and rubberized test handleDIN EN 61243-3 (VDE 0682-401): 2015 standard
-
Product
Voltage Detectors
JSC
-
The JSC family of devices provides a highly reliable way to determine if voltage is present downstream of the disconnector or circuit breaker knives during zero-energy shutdowns. They dramatically increase the safety of personnel performing maintenance on electrical equipment. When voltage is present downstream of the disconnector knives, one or more LEDs on the JSC-88A will remain illuminated. The JSC's compact design allows for direct installation on the disconnector door, starter, or control panel.
-
-
Product
FPGA Impulse Response (FIR) Filter Fo Gage Digitizers
eXpert / Finite Impuls Response (FIR)
-
The onboard FIR Filtering eXpert FPGA DSP feature is a powerful method for removing unwanted signal features (like noise) and emphasizing signal features of interest.
-
Product
voltage controlled crystal oscillator
VCXO
-
A VCXO (Voltage Controlled Crystal Oscillator) is a crystal oscillator the output frequency of which is controlled by adding an external control voltage via a frequency control input on a variable capacitance component such as a varactor diode connected in parallel to a load capacitance (CL). Epson VCXOs are divided into two types according to Voltage-Frequency (V-F) characteristic slopes depending on the AFC (Automatic Frequency Control) input configuration of the VCXO. One is a VCXO with a positive V-F slope and the other is a VCXO with a negative V-F slope. Please note that the input voltage of a control circuit will vary according to the individual type, as shown in Figs. 3 and 4. Epson's VCXOs are capable of either, depending on the customer's preference. Epson's VCXOs have been increasingly used for broader applications such as slave oscillators in phased-lock loops, or frequency modulators. Among the above types, a VCXO combined with a TCXO is called a VC-TCXO , respectively. These components have the merit of delicately controlling their output frequency electrically.
-
Product
Clock Generator Module
M8008A
Clock Generator
The M8008A is designed as sample clock source for the M8199A 128/256 GSa/s Arbitrary Waveform Generator. It can also be used as a standalone low-jitter clock source for other applications. It comes as a 1-slot AXIe module, which allows the M8008A plus up to two M8199A AWG modules to be plugged into a single 5-slot AXIe chassis.
-
Product
High Voltage Probe
HVP-15HF
-
*MAX.VOLTAGE:15KV DC.*BANDWIDTH:DC~50MHz.*DIVISION RATIO:X1000.*SIGNAL/NOISE:>60dB(1KHz)
-
Product
Voltage Dip & Swell Simulators
VDS Series
-
A simulator to reproduce voltage variation phenomena in commercial power supplies (AC100V/200V).This type of immunity test against voltage variation phenomena is defined in IEC 61000-4-11 and is widely used in many industries.
-
Product
Sweep Generator
G440XE
-
The G440XE Sweep Generators are portable powerful wideband general-purpose sources for swept and CW microwave measurements in local or remote operation modes. It incorporates the efficiency of micro-processing control with state-of-the-art BWO oscillator to produce a high performance sweep generator system suited for either manual or automated measurements.
-
Product
High Voltage Seasoning Equipment
-
This equipment is used to remove the bars that are in contact with the surface of vacuum interrupters.
-
Product
Voltage Dividers
-
Measurements International Ltd.
A series of resistors or capacitors which can be tapped at any intermediate point to produce a specific fraction of the voltage applied between its ends.
-
Product
Voltage Datalogger
S5011
-
Data logger is designed for record of voltage. Values are stored to a non volatile electronic memory. Data transfer to the personal computer for further analysis is performed via USB, RS232, GSM or Ethernet interface by means of a proper adapter.
-
-
Product
Standard 1.60 (45.00) - 4.50 (128.00) General Purpose Probe
EPA-3E
General Purpose Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 35Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Alternate 0.50 (14.00) - 2.50 (71.00) General Purpose Probe
P2662BG-2V2S
General Purpose Probe
Current Rating (Amps): 3Average DC Resistance lower than (mOhm): 30Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 68Full Travel (mm): 1.73Recommended Travel (mil): 50Recommended Travel (mm): 1.27Overall Length (mil): 575Overall Length (mm): 14.60
-
Product
Network Traffic Generation
-
Netropy Network Traffic Generators offer a brand new approach to traffic generation. Move away from outdated, expensive machines and unreliable freeware, and experience the unmatched ease of use and repeatable results that Netropy Traffic Generation provides.
-
Product
Voltage and Current Amplifier
CMS 356
-
The CMS 356 is a voltage and current amplifier for analog low-level signals provided by a CMC test set or by any other signal source, such as a digital real-time power system network simulator. When used in combination with a CMC test set, the amplifier extends the capabilities of the test set to provide additional output channels and higher amplitudes.
-
-
Product
Breakdown Voltage Tester
ZDS-50B
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-4; Inspection standard: JB/T4279.11-2008Used to test the breakdown voltage performance under room temperature of enameled round and flat wires with nominal conductor diameter of 0.018mm and above;Three voltage rise speeds are available: 20V/s, 100V/s and 500V/s, with error being ±5%;Three test methods can be adopted: round bar method, twist pair method and ball method;Clamp a group of test samples (5 for each) once, available to complete breakdown or withstand voltage test for any of sample one by one or individually; breakdown voltage and withstand voltage time would be automatically saved for future enquiry; all operations would be automatically completed;Capable of conducting high temperature breakdown voltage test in combination with RDS-50 thermal-state voltage tester;LED would automatically display test results and automatically return;During sample breakdown, breakdown voltage indication value would be automatically locked, free from flashing, and the test result is distinct and relatively clear;Equipped with test fixture for round rod method and twist pair method as well as the test weight for round rod method;Equipped with ball method test device (steel balls are prepared by user);Test door is provided with safety interlocking device, compliant with relevant regulations on high voltage testing equipment.
-
Product
Test Case Generator
Hexawise
-
Use Hexawise to design better tests. Maximize test coverage with the minimum number of test cases. Find twice as many errors per tester hour. Manually-designed software test plans often omit combinations of functions and configurations that need to be tested. Hexawise leaves no gaps and ensures all important combinations get tested.
-
Product
Voltage Meter
MN8I
-
The МН8И mezzanine module (mezzanine) is designed to measure instantaneous voltage values over eight differential channels isolated from each other.
-
Product
Signal Generator
SGA4
-
The C.Scope SGA4 is an affordable Signal Generator designed for use alongside a CXL4 or DXL4 Cable Avoidance Tool. It enables significantly more underground utilities to be detected including street lighting cables.
-
Product
Programming File Generation
-
Corelis will process your design information, create all necessary programming files, and verify the programming works using your actual hardware. This is a complete "turn-key" service resulting in a fully functional flash programming solution. For companies short of resources, those who are under a tight deadline, or for those who are new to boundary-scan and need a programming solution in the shortest time possible, this is an excellent way to minimize your investment and maximize your effectiveness.
-
Product
Surge Voltage Generator
SSG 2100
-
Cable fault location with the BAUR SSG 2100. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* Automatic discharge unit
-
Product
3KV High Voltage Test
-
45EHV/VC20EHV: 4.5inch High Voltage Motherboard for Celadon Element™ 20mm VC20EHV VersaCore™ and VersaJet™ System
