1553 Interfaces
Mil-Std-1553 interfaces.
-
Product
PXI Remote Control Interface Modules and Kits
Remote Control Interface
Take advantage of the latest high-performance, low-cost desktop PCs for control of your PXI system.
-
Product
VME Intelligent Interface Card
IIB-1553-VME
-
The IIB-1553-VME is an intelligent interface card for dual redundant MIL-STD-1553 applications.
-
Product
MIL-STD-1553 A / B Test And Simulation XMC Module
XMC-1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
Power Interface Board 6U, 1 PSU connector with AC pins
106PIBM601-9001R
-
The PIB 6U 1 slot has one power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
1 Or 2 Stream MIL-STD-1553 PMC Test And Simulation Modules With Prog. Coupling,onboard Bus Network And Variable Output Amplitude
AMCX1553-xT
-
MIL-STD-1553 Test and Simulation modules for PMC with 1 or 2 Dual Redundant streams plus 8 Discrete I/O’s (on Rear-I/O).
-
Product
SIP-90-5 Test System Interface Probe
SIP-90-5
ICT/FCT Probe
Overall Length (mil): 1,000Overall Length (mm): 25.40Rec. Mounting Hole Size (mil): 55Rec. Mounting Hole Size (mm): 1.40Recommended Drill Size: #54 or 1.40 mm
-
Product
GPP-95-2 Test System Interface Probe
GPP-95-2
ICT/FCT Probe
Overall Length (mil): 375Overall Length (mm): 9.53Rec. Mounting Hole Size (mil): 85Rec. Mounting Hole Size (mm): 2.15Recommended Drill Size: #44 or 2.15 mm
-
Product
CANdo Interface
NET50003
-
CANdo is a compact USB to CAN interface, that allows a PC to be connected directly to an embedded CAN bus. In conjunction with the FREE CANdo Application software, CANdo provides a simple, yet powerful means of testing & analysing a CAN network. The FREE CANdo SDK allows CANdo to be easily integrated into any Windows based program.
-
Product
Fibre Channel Test & Simulation Interface for PCI-X
PCI-X-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
Interface
P-SER
Interface
P-SER I/O product is a native PMC form factor interface providing real-time serial input and output with high time-precision reception/input time-stamping, scheduled transmission/output, event triggering and interrupt support. This interface is designed to meet the needs of both the simulations/test and the real-time embedded applications whether in Windows or VxWorks environments.
-
Product
Interface Converters
-
Electro Standards Laboratories
Supporting a variety of medias, applications, and entities such as Casino/Lottery VLT Networks, Industrial Process Control, Government Laboratories, etc.
-
Product
Isolated Serial To Analog Interfaces
-
ICS's Serial to Analog Interfaces are designed to provide isolated analog and digital drive signals to control power supplies and other devices. Available in rack mountable Miniboxes™ and IN OEM board versions. All of ICS's Serial to Analog Interfaces are fully IEEE-488.2 compliant and HP-IB compatible.
-
Product
Automatic Liquid Interface Tension Meter,Surface Tension Analyzer,Oil Interface Tension Meter
-
Chongqing Assen Power Equipment Co., Ltd
Our HTID-1 Automatic Interface Tension Tester is used to test various liquid surface tension and interface tension based on the ring method that is simple and high accurate, which is widely applied in electric, petroleum, chemical, medicine, food, and teaching filed.
-
Product
Audio Interfaces
RME
-
RME offers a range of multichannel audio interfaces that work well with SoundCheck. Listen supplies RME interfaces fully tested and pre-calibrated for use with SoundCheck.
-
Product
Interface (PMC)
QPM-1553-TB
Interface
The QPM-1553-TB provides the highest level of performance, flexibility and interface density for MIL-STD-1553A/B via PMC (PCI Mezzanine Card) to Thunderbolt 3 device. The QPM-1553-TB is integrated with powerful software that reduces development time. All 1553 databus functionality is supported from our advanced API (Application Programming Interface).
-
Product
NI-9862, CAN Interface Module
781639-01
Interface Module
1-Port, High-Speed, Flexible Data Rate C Series CAN Interface Module—The NI‑9862 is a high-speed Controller Area Network (CAN) Flexible Data‑rate (FD) interface for developing applications with the NI‑XNET driver. The NI‑9862 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other data acquisition measurements in the same NI CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same NI CompactRIO chassis.
-
Product
PMC Carrier for PCI Card Interface
TPCI270
-
The TPCI270 is a standard 33 MHz, 32 bit PCI carrier for a single PMC Card. Itprovides PMC front I/O and PMC P14 rear I/O. This PMC to PCI adapter is used to build modular, flexible and cost effective I/O solutions with PMC devices in standard PCI systems.
-
Product
MIL-STD-1553 USB & LAN Test & Simulation Module
UXI-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsConcurrent BC, 31 RTs, and BM operations - Physical Bus ReplayFull error injection/detection capabilities - Programmable trigger and capture - Programmable Bus Coupling and Output Voltage Levels - Onboard IRIG-B time code encoder/decoder for Synchronization - Time Synchronization to IEEE 1588 via Ethernet LAN port - 10 Discrete I/O Interfaces (5 Outputs / 5 Inputs) - Operates from a single USB or Ethernet LAN connection - Supports SAE AS4112/4114 protocol testing requirements- Flight Simulyzer™ GUI Analyzer software
-
Product
PXI Automotive Ethernet Interface Module
Ethernet Interface
The PXI Automotive Ethernet Interface Module communicates with Automotive Ethernet so that you can use the NI‑XNET driver or standard networking drivers to develop applications that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). It provides up to four independent endpoints or up to two network terminal access points (TAPs). With onboard hardware timestamping and the ability to act as 802.1AS masters or slaves, the PXI Automotive Ethernet Interface Module can synchronize with an external network as well as the rest of a PXI system.
-
Product
NI-9853, CAN Interface Module
780178-01
CAN Interface
2-Port, High-Speed C Series CAN Interface Module—The NI‑9853 is a high-speed Controller Area Network (CAN) interface for developing FPGA-based applications with the NI‑RIO driver on CompactRIO. The NI‑9853 is ideal for low-level FPGA‑based control and triggering applications that are programmed using the LabVIEW FPGA Module. The NI‑9853 is ideal for byte-level manipulation of CAN frames using the LabVIEW FPGA Module. The NI‑9853 is only compatible with CompactRIO systems.
-
Product
PXI/PXIe MIL-STD-1553 Multiplexer, Single 8-Channel, 2-Pole
40-739-003
Multiplexer Module
The 40-739-003 (PXI) and 42-739-003 (PXIe) are single 8-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
Product
ARINC 664 Part 7 Test & Simulation Interface for PCI
PCI-C664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfacesSimulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboardError Injection including Runt Frames, Short IFG, and Invalid MAC FCS - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
8-port Serial Interface, Modular, With/without Optical Isolation, 3.3V/5V
APCIE-7800
-
The APCIE-7xxx series of ADDI-DATA allows you to implement either 1, 2, 4 or 8 modules on serial interface boards.
-
Product
Two Port Fibre Channel/MIL-STD-1760E Network Interface Controller
cPCI-HS1760-NCSW-2
-
Avionics Interface Technologies
Integration of Up Fibre Channel and Down Fibre Channel interfaces - Embedded Network Controller (NC) with four priority levels - Two F/AE ports for communication to external devicesInternal four port non‐blocking fabric switch for communication between NC and external devices - Four port non‐blocking Fibre Channel Switch - Meets the requirements of MIL‐STD‐1760E and AS5653 standards - Initialize via the Fast Fabric Initialization (FFI) protocol - ANSI C API enabling complete FC-AE-1553 NC functionality and management - 3U Conduction-cooled Compact PCI module - Designed for extended temperature operations
-
Product
DAQ User Interface Software
DAPstudio 3.00
-
If you need to deliver a data acquisition system quickly and you want to develop a good user interface for it, then download DAPstudio 3.00 and see how that could help. You now can use the latest (full) version of DAP Measurement Studio software from Microstar Laboratories, maker of Data Acquisition Processor (DAP) boards and software, for an unlimited trial period at no charge.
-
Product
Analog Device Interface
ADI-123
-
Model ADI-123 Analog Device Interface offers the means of computer interfacing almost on any device whic is provided with dc inputs and/or outputs, for example programmable power supplies and measuring instruments of all kinds.
-
-
Product
Advanced ARINC-429 Testing Ethernet Appliance - Parametrics TX Variable Voltage, Digital Signal Generator and RX Signal Capture
ENET-A429P
Ethernet Interface
eNet-A429P™ is an innovative product that provides “remoting” of ARINC operations on 10/100/1000 Ethernet IP/UDP local area networks (LAN). eNet-A429P is a small, low-power, device ideal for details ARINC signal testing with variable voltaqe control of the first 3 TX channels. Alta has combined the industry’s most advanced 32-bit ARINC FPGA protocol engine, AltaCore™, with a real-time IP/UDP thin server. The customer can implement their application with the same feature-rich application programming interface, AltaAPI™, as used with standard cards – often without even recompiling – the utlimate in code portability.
-
Product
PCI-8532, 1-Port, DeviceNet Interface Device
781062-01
Interface
The PCI‑8532 is a high-speed DeviceNet Interface for developing applications with the NI‑Industrial Communications for DeviceNet driver. DeviceNet is based on the controller area network (CAN) physical layer and increases strength and interconnectivity by specifying various parameters, such as the required cable length, connectors, and baud rates. The DeviceNet specifications are managed by OVDA, Inc. You can program the PCI‑8532 to add high-performance master/scanner or slave capabilities to DeviceNet networks.
-
Product
4-Port Serial Interface
APCI-7500-3
-
This Model has a 37-pin D-Sub male connectorRS232, RS422, RS485, 20 mA Current LoopModular structure through SI modulesWith or without optical isolationMode configuration free for each port128-byte FIFO-buffer, common interruptTransfer rate programmable up to 115,200 BaudOption: up to 1 MBaud for RS485 and RS422Automatic direction recognition for RS48Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)Transmission mode asynchronous, full, half duplexTransfer rate: progr. up to 115.2 kBaud up to 1 MBaud on requestProtocol: 5, 6, 7 or 8-bit character 1, 1? or 2 stop bitsParity: even, odd, none, mark or spaceInterrupt lines: automatic through BIOS
