Contamination Monitors
-
Product
PXI 16x4 Signal Insertion and Monitor Matrix
40-525A-002
Matrix Switch Module
This is a PXI signal insertion and monitor matrix with switched pass thru connections on both X and Y axis. It is also available in a 34x4 format and can be used for signal insertion and monitoring purposes on connections between the UUT and test system.
-
Product
Pt RTD Temperature Monitor
SIM923
-
Stanford Research Systems, Inc.
The four channels in the SIM923 have independent, stable 1 mA current sources to provide sensor excitation. Sensor resistance is determined ratiometrically with a half-bridge circuit consisting of the sensor and an internal reference resistor.
-
Product
Process Ozone Monitor
Model 465M
-
Teledyne Advanced Pollution Instrumentation
The Model 465M is a microprocessor based medium range ozone monitor for measuring process ozone concentrations in water treatment, food processing, and research applications. The design has been specifically optimized for applications requiring the measurement of ozone at near-ambient pressure such as water treatment contactor off-gas measurement. The Model 465M has been designed to give accurate and stable readings over long time periods with little or no maintenance or calibration. The Model 465M is available in a NEMA 4X wall mount enclosure.
-
Product
Washwater Monitoring System
EG-100
-
Washwater Monitoring System for NOx and SOx Scrubber.Monitoring pH/Temperature, Turbidity, and PAH.EG-100 has flow type sensors.
-
Product
Torsional Vibration Monitoring Systems
-
Advanced Telemetrics International
Are used for Noise Vibration and Harshness (NVH) testing and analysis in automotive drivetrain, wind turbine gearbox and various other applications where measuring or monitoring rotating vibration is important. These systems are used to transmit torsional acceleration from a rotating shaft or component, while the machinery is running.
-
Product
Advanced Monitoring Probe
DVB-T/T2
-
Combined with a Network Monitoring System or not, the EdgeProbe Advanced provides a powerful broadcast network alert & diagnosis tool allowing DTV network operators to monitor global trends and anticipate potential failures.EdgeProbe Advanced is able to monitor DVB-T and DVB-T2 signals at transmitter outputs, through its RF inputs (up to 4 in 1RU), as well as at modulator input and at Head-End/distribution links, through its ASI and IP inputs.
-
Product
Phase Monitoring / Potential Selector Relay
-
This is a phase failure relay suitable for 3 phase supplies. The relay is designed to automatically change over from the primary supply to the secondary supply if any phase of the primary supply has faulted.
-
Product
Collapsible 6 Inch Charge Plate Monitor Assembly
CPM-760A
-
- 6" x 6" (15 cm x 15 cm) conductive plate- Total system capacitance of 20 pF ± 2 pF- Meets the requirements of ANSI/ESD STM3.1 and ANSI/ESD SP3.3- Designed to perform audits on overhead ionizers and room ionization systems- Flexible to also evaluate and balance bench top ionizers- Completely collapsible for compact storage- Designed to be used with the PFM-711A and PFM-711B
-
Product
Non-Destructive Particle Monitoring
PARTi
-
PARTi provides a complete solution for non-destructive surface particle monitoring of consumables, parts and cleanroom apparel.
-
Product
Monitor Holder for 19" Rack Installation
ZZ-0017-01
-
- Monitor holder for 19 “rack installation- 9 U (400 mm)- Can be used universally with LED, LCD and plasma monitors- Compatible with the VESA standards 75 x 75 and 100 x 100 mm- Record in portrait and landscape format
-
Product
21.5" Full HD Standalone HD Base-T Multi-Touch Industrial Monitor
SPC-821(M) V2
-
21.5" Full HD TFT LED LCD display16:9 widescreen with P-CAP multi-touch controlSupport HD Base-T long distance video streamingFront-facing LED indicators show operating statusSilicone-free enclosure with all-round IP65-rated protection
-
Product
System Status Monitoring Software
CHM
-
The R&S®CHM system status monitoring software is an integrated, system-specific solution for continuous monitoring of key system parameters in systems from Rohde & Schwarz. It monitors devices and system components fully automatically, outputs warnings and alarms to operators if system components approach or reach critical operating states, and assists maintenance personnel in fault diagnosis..An extensive set of analysis tools, such as the visualization of measured values in time-sequence charts, helps system administrators to carry out maintenance work and identify errors.
-
Product
Particulate Meters, Monitors, Instruments
-
GrayWolf’s 6-channel handheld, desktop, and wall-mount air particulate meters, PM2.5 and PM10 monitors, and particle counters all include high accuracy sensors and precision pumps. They interface with GrayWolf DirectSense®, AdvancedSense® XM, and WolfSense® LAP enabled instrumentation. They also can connect via WolfSense Mobile apps on Android and iOS devices. Use these particle meters as stand-alone instruments, and/or interface them to display and log particulate concentrations directly on a GrayWolf instrument, Mobile PC, smartphone/iOS, Android device, and/or to the cloud, all simultaneously with one or more GrayWolf multi-sensor probes.
-
Product
Monitoring and Documenting Vacuum and Pressure in a Containment Area
Omniguard 4
-
Engineering Solutions Inc. (ESi)
The Omniguard 4 is the clear choice for monitoring and documenting Vacuum and Pressure in a containment area. Ideal for Asbestos, Lead and Mold abatement and Clean Room monitoring. The Omniguard 4 utilizes state of the art pressure measurement technology to accurately monitor pressure inside a containment area.
-
Product
Flow Meter / Monitor
NivuFlow Mobile 600
-
The NivuFlow Mobile 600 was developed particularly for long-term measurements in field operation without external power supply. Measurements for checking and verifying can be carried out with the self-sufficient and portable system without any problems even in harsh environments. Battery lifetimes of several weeks or even months reduce personnel costs for maintenance and data readout significantly.
-
Product
Monitor / Annunciator
RTP-1
-
The RTP-1 Monitor is a general purpose annunciator. Designed for 19 “ rack installations, the RTP-1 is complete with a noise immune filter. The ten point RTP-1 features latching memory. Easy to install and easy to operate, this low power monitor has front panel plug-in replaceable LEDs for indication and a single system Test and Reset buttons.
-
Product
Multi Monitor
MD
-
It is a 30mm monitor with 2 screens and 3 colors that displays 1-5V analog signals converted into numerical values.Since various unit displays are possible, it is ideal for monitoring pressure sensors and flow rate sensors.
-
Product
Noise Monitoring
-
Acu-Vib Electronics Acoustic & Vibration
instruments and systems used to measure, record, and assess sound levels in various environments.
-
Product
Vibration Condition Monitoring
-
Vibration Condition Monitoring is a predictive maintenance method that allows for early detection of problems with vibration. The techniques of Vibration Condition Monitoring share a common objective of indicating early signs of deterioration or malfunction in machinery. It also helps to reduce failures in your workplace as well as increasing your safety and machine performance.
-
Product
Bus Analyzer, Monitor, Debugger & Programmer
BusPro-I™
-
The BusPro-I has all the power, flexibility, and features you need to monitor and debug the I2C bus circuitry on your board. The BusPro I2C can be used to monitor and log I2C bus traffic in real-time, generate I2C transactions to communicate with peripheral components on the bus, and in-system program I2C compatible EEPROMs.
-
Product
15" XGA Industrial Monitor With Resistive Touchscreen And VGA / HDMI Port
FPM-1150G
-
15" XGA TFT LED LCD with 70,000 backlight life timeRobust design with aluminum front panelSupports VGA or HDMI interface with USB touchscreenSupports panel, wall, desktop, or VESA arm mountingLockable HDMI port (optional)
-
Product
In IIoT And Industry 4.0, Customers Need Data Visualization For Process Management. The FPM-710SW Is A Sleek, Industrial-Grade Touchscreen Monitor.
FPM-710SW
-
USB Type-C connection touch monitor 1920 x 120010.1" WUXGA TFT LED LCD with true-flat touchscreen16:10 wide screen aspect ratio, increases viewing area by 40%Supports multi-touch control via USB interface in Windows 7/8/10 OSSlim design enables easy installation with Build-in panel mount kitSupports various mount options: panel, desktop, and VESA armTouchscreen with reliable glass surface and P-CAP touch controlRobust system with Die-casting aluminum chassis and IP66-rated aluminum alloy front bezelFirst single cable industrial touch monitor
-
Product
Web Performance Monitor
-
Website monitoring software built to find and fix internal and external site and app performance issues
-
Product
Environmental (Radiation) Monitoring System
Hawk® EMS
-
The Hawk® EMS is a wall or tripod-mounted radiation monitoring and alarm system designed for use with the Hawk® Radius dual sensor radiation probe. Each EMS System comes with a Hawk Radius Probe. The system is extremely energy efficient and can run for weeks on an internal 9 volt back-up battery if power fails. It is well suited for operating on a small solar panel, which is an optional accessory. The Hawk® EMS features two displays that show the radiation levels measured by each of the probe’s two detectors: the weatherized “pancake-style” Geiger-Mueller tube — which measures alpha (if configured for it), beta, low energy gamma, and x-radiation — and the energy-compensated gamma tube which measures penetrating gamma dose rate. The probe can be mounted next to the EMS system or outdoors, or in adjacent rooms on cables up to 100 ft in length. Standard cable is 3 meters in length. Optional signal booster can support cable lengths longer than 100 feet. Optionally the system can also be configured to share data on ethernet or wireless networks.
-
Product
Indoor Air Quality (IAQ) Meters, Monitors
-
For handheld, semi-permanent and long-term IAQ measurement
-
Product
Control and Monitoring of Machines
Millenium 3
-
Easy to program and to implement, it enables the control and monitoring of machines and automation installations with up to 50 I/O. It is positioned right at the heart of the Crouzet Automation range.
-
Product
PXI Monitored Multiplexer, Single 64-Channel, 1-Pole
40-619-301
Multiplexer Module
The 40-619-301 is a high density PXI 2 A multiplexer module in single 64-channel configuration using high quality electro-mechanical signal relays allowing each channel to switch current up to 2 A and voltage up to 250 VAC/DC.
-
Product
Open Frame Monitor
-
Advantech Open Frame Monitor IDS-3100 series provides touch screen monitors with slim open front frame design and supports rear mount and VESA mount with integrated bracket design for easy installation.
-
Product
Non-Dispersive Infrared Monitors
OPTI-Sense Series
-
Teledyne Advanced Pollution Instrumentation
The OPTI-Sense series of sensors is based on Non-Dispersive Infrared (NDIR) technology. They are designed to precisely measure the absorbance in the infrared spectrum of specialty gases typically found in semiconductor applications. They are very compact and designed with no moving parts, making the OPTI-Sense robust and ideal for continuous in-situ gas monitoring of semiconductor processes.
-
Product
4-Channel Broadcast Monitor
-
The COMM-connect Entry Level Broadcast Power Monitor type 3025 can control two external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. Equipped with the RMS Probes the Power conversion algorithms handles multi carrier, multi mode signals. With the 3026 Diode base probe the power readout gives good repeatable results. The power readout is auto scaled and VSWR will be calculated between the two probes. The COMM-connect Entry Level Power Monitor gives a number of application to monitor and control the last part of your RF network installation from transmitters to the antenna.
