-
product
Tracking Index Test Apparatus
CX-L19
Shenzhen Chuangxin Instruments Co., Ltd.
It applied with rectangle size of platinum electrode, each electrode can force to the sample is 1.0±0.05N. Electrode Distance: 4.0mm±0.01mm, included angle: 60°±5°. Electrode Voltage: 100~600V, (48~60HZ) adjustable, when the short-circuit current at 1.0±0.1A, the voltage goes down less than 10%. The liquid drop device can make the liquid height from 30~40mm (adjustable), drops liquid size is 44~55 drops/1cm3. The interval drops of liquid is 30s±5s (adjustable). During the testing, the short-circuit current is more than 0.5A to keep 2 seconds, then shut off current, it show the sample not pass. Inside dimension: 0.5CBM and outside dimension: 630mm*390mm*750mm.
-
product
Fully Automatic Close Link Single Phase Energy Meter Test bench
SY 8125
Hong Kong Songyang Industrial Ltd.
The devices are fully made by aluminum alloy materials and the table board is composed of fireproofing and heat-proof materials. The output voltage and current use soft startup and stop. It has the protection functions of voltage short circuit, current open circuit and power amplification exception. The device has the features of high stability, good reliability and large output power
-
product
Uniload Voltage Transformer Test Set
2J6
The Type 2J6 Knopp Uniload Voltage Transformer Test Set consists of three major parts: When the Knopp Precision Transformer in the 2J6 set is compensated for, and used with, a secondary burden of 15 volt-amperes, for example, the ratio of this precision transformer is well within 0.02% and the phase angle is well within 2 minutes. The transformer, in common with other Knopp Precision Multirange Transformers, is wound so that it has practically the same ratio and phase angle accuracy on all ranges.
-
product
Rapid Decompression Test Chambers
CA-RD(H)
CSZ's rapid decompression test chamber is designed to simulate rapid decompression for testing aircraft avionics. The environmental chamber meets the environmental conditions and test procedures for airborne equipment referenced in the RTCA DO-160 test specification. The DO-160 specification was designed to test sudden pressure changes starting from 8,000 feet to 60,000 feet (536 to 55 Torr) in 15 seconds. An altitude of 8,000 feet (536 Torr) was used for the initial cabin altitude and 60,000 feet was used for the final cabin altitude after decompression. This test specification is used to identify failures of materials inside of the cabin and the reaction to the surrounding environment.
-
product
VITA 62, 3U Test Fixture
TF-3U-7B041-1
This Power Supply test fixture is being proposed as a tool for checking Injector / Ejector operation, proper alignment of the VITA 62 connector and proper alignment of both keys on a Single slot, 3U, VITA 62/SOSA power supply.
-
product
Self-Sufficient Test System
MFTS100
Computer Gesteuerte Systeme GmbH
The MFTS100 is a self-sufficient test system with optional integrated touch screen for easy operation and display of measurement data or running processes.
-
product
Deluxe Relay Test Set
60660
Jumpers have tabs for clamping and flat pads to place test leads on. No need to pierce wires or connect multiple jumper wires. Also Includes Test Lead Kit for easily and securely connecting Relay Test Jumpers to a multimeter. Jumper wire may be used between common and open to close the relay circuit for testing and has a test port to easily check voltage. Also provides access for a clamp-on amp meter. Relay Puller Pliers easily remove electrical relays without damage to the relay or electrical box.
-
product
Interconnect Test Leads
142-1
This 64 inch pair of test leads connects with many different testing accessories and probes. Especially those found in typical test lead kits and assortments. The ends terminate in universal size 4mm banana plugs.
-
product
Benchtop Test System
300 Series Benchtop ATE
The Circuit Check 300 Series benchtop ATE Test Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 300 Series Benchtop ATE, test procedures can become automatic, with test steps and go/ no-go limits easily programmable in common tabular form. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
product
Configurable Servo Test Controller
The controller incorporates proven PID and Cascaded Incremental technology to provide a configurable test controller for servo hydraulic and generic test systems that require synchronized multichannel control.
-
product
Chloride Ion Test Kit for Abrasives
134A
Contamination can build up, particularly if the blast media is recycled several times. Using the Elcometer 134A Chloride Ion Test in the field will accurately identify contamination and prevent costly surface-related failures.
-
product
Tan Delta Test System
Precision measuring bridge is designed for determining the capacitance and dielectric dissipation factor of liquid and solid insulants, cables, capacitors, line transformers, generators, motors, bushings etc. Furthermore it can also be used for power loss measurement on shunt reactors or similar apparatus. This system is suitable for both low and high voltage measurement at line frequency. Measurement reports can be printed. This measuring equipment has been specially developed to maximise efficiency in production and quality control environments. Its outstanding accuracy also makes it suitable for laboratory and research applications.
-
product
Test Management Platform
Comprehensive suite of test management products fosters global project team collaboration, drives down costs, shortens release cycles, and provides real-time visibility into the status and quality of the software projects. Manage all aspects of software quality; integrate with JIRA and various test tools, all within the enterprise. Manage all aspects of software quality; add test management capabilities right inside JIRA.
-
product
PC Based High Current Test Set for Circuit Breakers and Temperature Rise Test Equipment
This equipment comprises of high current source for testing of circuit breakers with additional facility for temperature rise testing (thus incorporating testing for moulded case, vacuum & air circuit breakers as per IEC 60947-2). The system integrates a servo controlled source with closed loop current feedback to maintain the current constant. It has the necessary instrumentation for maintaining current at full load & other conditions arising in testing at high current. The bench has a PC based control system with temperature data logger (24 channel with ch-ch isolation amplifiers). The data logger displays as well as stores a set of temperature values with time.
-
product
Sample Test
For performance evaluation and model selection at the time of your purchase, we have welding laboratories at our Shin-Yokohama facility where you can perform welding tests using actual equipment.
-
product
Boundary-Scan Test Coverage Analysis Tool
ScanExpress DFT Analyzer
Test coverage statistics provide engineers and managers valuable information to make critical decisions in product development and manufacturing.ScanExpress DFT Analyzer is an automatic test coverage analysis tool for printed circuit boards and systems that include a mix of boundary-scan and non-boundary-scan devices. The tool assists design and test engineers to increase fault coverage and reduce boundary-scan test procedure development times. Using ScanExpress DFT Analyzer results in better informed test decisions.
-
product
Cable Test Van
Techno Instrumentation (India) Private Limited
Cable fault locating van with installation according to users specifications and requirement.
-
product
Mixed Signal Test Systems
MTS1010i
The MTS-1010i is a more economical version of the MTS-2010i & MTS-1020i testers. It has a reduced platform size and reduced power supplies. Like the other testers in the MTS family it is a highly cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process.
-
product
Semiconductor Test Hardware Solutions
A critical element of every semiconductor test solution is the interface between the device and ATE. The hardware team at Test Spectrum has produced thousands of successful test interface solutions for some of the most challenging semiconductor products on all major ATE platforms. Our in-house team of PCB design experts has an added advantage of direct access to our senior test engineering staff.
-
product
ADAS Test
Advanced driver assistance systems (ADAS) are introducing new technology into vehicles. They demand test systems that are adaptable and future-proof, so they can integrate all the technology used today and be ready for whatever tomorrow brings.
-
product
RFID Test System
RFID test system of Peritec is making FPGA board (IF-RIO) the processing of the IF band. This reading of the code, called (Electronic Product Code) EPC is required for RFID tag ISO18000-6 TYPEC of (EPC C1 G2). However, it did not provide treatment too late in the traditional instruments.
-
product
Strain Gauge for Special Application
Zhonghang Electronic Measuring Instruments Co. Ltd.
Zemic Strain Gauge for Special Application
-
product
Copper Test Solution
DSX CableAnalyzer™ Series
The DSX CableAnalyzer Series copper test solution enables testing and certification of twisted pair cabling for up to 40 Gigabit Ethernet deployments and will handle any cabling system whether it is a Cat 5e, 6, 6A, 8 or Class FA and I/II. Certifying a cable is one part of a process that starts with system design and ends with system acceptance. The faster that process goes, the more profitable you'll be. Unfortunately, there are a lot of things that slow the process down setting up the tester ...show more -
product
Air-Cooled Universal Test Platform
Diamondx
Diamondx semiconductor test system extends Cohu’s low-cost, high-throughput production test solution platforms to high pin count, higher site count wireless, mobility, SOC, Flat Panel Display drivers, Power Management, and microcontrollers. Designed to meet the cost drivers IC companies face, Diamondx extends Cohu’s leadership in lowering the cost of operations.
-
product
EFI Test Light-Bosch Type
3405
Peaceful Thriving Enterprise Co Ltd
EFI Test Light-Bosch Type
-
product
300 HP Complete Bench Hydraulic Test Center
HTC-300
The Hydraulic Test Center (HTC) is a versatile machine designed to test heavy-duty, off-highway hydraulic components. The 300 hp (224 kW) HTC Complete Bench is for the dealer that services components from a predominately medium size machine mix such as large construction equipment (loaders, dozers, excavators). The Complete Bench offers full functionality to test all types of pumps and motors including: transmissions, hydraulic motors, hydraulic cylinders, valve blocks, torque converters, open and closed loop pumps.
-
product
Radiator Test and Repair Stand, Type 2 (Two Station)
9001
The Radiator Test and Repair Stand, P/N 9001, meets all requirements of military specification MIL-S-4534C, is completely self contained and requires only connection to a source of shop air and gas to place in operation.
-
product
Rotor Test Systems
Automation Technology's RTS-3800 Rotor Test Systems offer an unparalleled ability to test the quality of die cast or PM rotors. The RTS-3800 is packed with standard features and like all of ATI's 3800 Series Test Systems; the RTS-3800 is backed by ATI's industry leading two-year limited warranty.
-
product
PCI Express 5 CEM Receiver Test Automation
N5991PC5A
The N5991PC5A is the receiver test automation software for bit error ratio testers, allowing you to test, debug and characterize PCI Express 5.0 CEM Add-In Cards and systems.
-
product
Visual Editor for the Automatic Test Markup Language (ATML)
ATML Pad
Reston Software offers ATML Pad, a visual editor for the Automatic Test Markup Language (ATML).The ATML formats are versatile but complex. Direct editing in XML is next to impossible, even with capable XML editors. ATML Pad overcomes this problem by exposing an application-specific visual interface. ATML Pad manages the complexity of the ATML formats, allowing you to focus on describing your tests. It abstracts XML ID references, allowing you to simply select the referenced item from a list. In ...show more
