Analog Digital
-
Product
Handheld Digital Multimeter, 3½ Digit
U1233A
-
Ergonomic shaped 6K counts DMM with flashlight, low input Z mode, non-contact voltage detection & continuity visual/audio alerts. Keysight Remote Link Solution enabled.
-
Product
PXI Digital Multimeter, 6 digit, High Performance
M9182A
-
The Keysight M9182A is a 6digit PXI digital multimeter that measures common parameters such as DCV, DCI, ACV, ACI, 2- and 4-wire resistance, frequency, capacitance, and temperature. It offers 40 ppm basic DCV measurement accuracy, excellent noise rejection, and handles inputs of up to 300 V. The M9182A offers advanced triggering capabilities, including pre and post triggering.
-
Product
FPGA Mezzanine Card
FMC168
-
The FMC168 is a digitizer FMC featuring eight ADC channels with 16-bit resolution and 250Msps sampling rate per channel.With a flexible clock generation and distribution scheme, the FMC168 allows control of sampling frequency and analog input gain through serial communication with a carrier card.
-
Product
64 Input USB Modular Digital I/O
U2652A
-
The Keysight U2652A USB Digital I/O is a cost-effective device with its offering of 64 opto-isolated digital lines. It comes bundled with the Keysight Measurement Manager (AMM) software for quick set up and data logging. Simplifying this further is the command logger function offered in the Keysight Measurement Manager that allows capturing of configuration commands that can be easily converted to snippets of VEE code. Other supported languages are VB, C++, and C#.
-
Product
4CH 16-Bit 80 MS/s PXI Express Digitizer
PXIe-9834
-
The ADLINK PXIe-9834 PXI Express digitizer provides high speed, high quality data acquisition with four input channels supporting up to 80MS/s sampling and 16-bit data resolution. This allows simultaneous recording of signals on all channels with no interchannel phase delay.The PXIe-9834 features external digital trigger input and triggers from the PXIe system timing slot and reference clock from the PXIe chassis, making it easy to achieve high simultaneous channel count recording of 8, 12, 16 and 20 channels. The PXIe-9834 is also equipped with 1GB of onboard memory for data buffering before transferring back to system memory. The PCI Express x4 Gen1 data bus is has enough bandwidth for direct streaming of ADC data back to system, if necessary.
-
Product
PXIe Semi-Dynamic Digital I/O Module, 64-Channel
42-419-001
-
The 40-419-001 (PXI) and 42-419-001 (PXIe) are a 64-channel digital I/O modules suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. They can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 125 MS/s on 24 Channels, 80 MS/s on 48 Channels, 48 Single-Ended Inputs, 24 True Differential Inputs
DN6.596-48
-
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
8/16-CH 16-Bit Analog Output Cards
PCI-6208/6216 Series
-
ADLINK PCI-6208/6216 series are 8 or 16-CH, 16-bit, analog output cards. The PCI-6208V-GL offers 8 voltage outputs with ±10 V range, featuring 15-bit monotonicity and 10 V/μs slew rate. The on-board analog switches minimize the power-on glitches. PCI-6216V expands the voltage output channels to a total of 16 for higher analog output density requirements. In addition to the voltage output functions, the PCI-6208A features 8 current outputs with ranges of 0-20 mA, 4-20 mA, and 5-25 mA. The daughter board EXP-8A provides high-quality voltage to current transducers. The PCI-6208A device is capable of delivering 14-bit monotonicity with 1.3 mA/μs slew rate. ADLINK PCI-6208 series devices provide high-resolution, high-density analog output functionalities and are suitable for ATE, signal generation, industrial process control, servo control and other industrial control applications.
-
Product
C Series Digital Module
-
The C Series Digital Module interacts with a range of industrial switches, transducers, and devices. Some modules include an LED per channel that indicates the state of the channel. It supports input, output, or a combination of digital lines, and they can interact with a variety of voltages and logic levels, so they are well-suited for a variety of benchtop and industrial environments. Additionally, the C Series Digital Module also offers isolation options and sinking or sourcing capabilities to add further protection to your digital I/O application. When you use the C Series Digital Module with CompactRIO, you can use LabVIEW FPGA to create custom high-speed counter/timers, digital communication protocols, pulse generation, and more.The C Series Digital Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
PCIe-5764 , 16-Bit, 1 GS/s, 4-Channel PCI FlexRIO Digitizer Device
785962-01
-
The PCIe-5764 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PCIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer.
-
Product
32-CH Discrete Input Modules
HSL-DI32-M-N/HSL-DI32-M-P
-
- Slave ID consumption: 2 consecutive from odd- "N" type for NPN sinking type sensor or dry contact; "P" type for PNP sourcing type sensor or wet contact- Photo couple isolation voltage: 2500 Vrms- Input impedance: 4.7 KΩ- Input current: ± 10 mA (Max), ± 12.5 mA (Peak)- Input voltage: ± 40 V (Max)- LED indicator: Power, Link and Input status- Power supply: +10 V to +30 VDC
-
Product
NI-9421, 24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module
783734-01
-
24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module - The NI‑9421 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels and has an LED indicating the state of that channel. The NI‑9421 offers isolation between the input channels and earth ground.
-
Product
PXIe 8 Bit High Speed Digitizer - 5 GS/s on 1 Channel, 1.5 GHz Bandwidth
M4X.2230-X4
-
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
PXIe-5764, 16-Bit, 1 GS/s, 4-Channel PXI FlexRIO Digitizer
785168-01
-
The PXIe-5764 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PXIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5764 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
PXIe-5764, 16-Bit, 1 GS/s, 4-Channel PXI FlexRIO Digitizer
785169-01
-
The PXIe-5764 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PXIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5764 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
FPGA PXIe High-Performance Digital I/O Card
GX3700e
-
The GX3700e is a user configurable, FPGA–based, 3U PXI Express card offering 160 digital I/O signals which can be configured for single-ended or differential interfaces. The card employs the Altera Stratix III FPGA, which can support SerDes data rates up to 1.2 Gb/s, digital I/O clock rates of 700 MHz, and features over 45,000 logic elements and 1.836 Kb of memory. The GX3700e is supplied with an integral expansion board providing access to the FPGA’s 160 I/Os. Alternatively, users can design their own custom expansion cards for specific applications - eliminating the need for additional external boards which are cumbersome and physically difficult to integrate into a test system. The design of the FPGA is done by using Altera’s free Quartus II Web Edition tool set. Once the user has compiled the FPGA design, the configuration file can be loaded directly into the FPGA or via an on-board EEPROM.
-
Product
4-CH 10/12-Bit 20 MS/s Simultaneous-Sampling Analog Input Cards
PCI-9812
-
ADLINK’s PCI-9812 and PCI-9810 are 4-CH, 10 or 12-bit, 20 MS/s simultaneous-sampling analog input cards. The high-speed analog input channels are single-ended, with hardware programmable input ranges of ±1 V, ±5 V and input impedances of 50 Ω, 1.25 k Ω and 15 M Ω. The onboard 32 k-sample A/D FIFO can buffer so data throughput is less than 100 Mbytes/s, the FIFO performs as the temporary A/D sample buffer, and as a rule of thumb, no data loss will occur. When four channels operate at 20 MS/s simultaneously, each sample generates two bytes, resulting in 160 Mbyes/s (4 channels * 20 M * 2 bytes) throughput, which exceeds the peak 132 Mbyte/s bandwidth of PCI bus. To avoid data loss, the 32 k-sample FIFO is the limitation of sample count. In addition to the onboard 40 MHz time base, users are able to supply the external time base in either sine wave or digital forms. The PCI-9810 and PCI-9812 also feature external digital trigger and programmable analog trigger, thus the conversion start point of multiple cards can be synchronized to external events. The trigger modes include software-trigger, pre-trigger, post-trigger, middle-trigger and delay trigger, further expands the capabilities of these high-speed devices. ADLINK"s PCI-9812 and PCI-9810 deliver cost-effective and reliable data acquisition capabilities and are ideal for vibration testing, image digitizing, ultrasonic measurement, biomedical research, ATE and other high-end industrial, scientific, and military applications.
-
Product
PXIe-6535, 32-Channel, 10 MHz, 40 MB/s PXI Digital I/O Module
780695-01
-
32-Channel, 10 MHz, 40 MB/s PXI Digital I/O Module—The PXIe‑6535 can continuously stream data over the PXI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
Product
PXI Digital IO: 32 inputs, 32 outputs, 0.3V to 50V
M9187A
-
The M9187A has 32 input channels that can be used for comparing inputs to user-defined thresholds between 0.3V and 50V, with 12mV setting resolution. Each input is protected up to 100V. In addition, the 32 output channels use a high current to drive the output high or low, and are capable of sourcing 0.4A from the high side or 0.5A sink from the low side of each channel. These outputs are protected against over-voltage or over-current conditions. Choose from the durable connector block or the standard cable connections.
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 5 GS/s on 4 Channels, 2.5 GS/s on 8 Channels, 1.25 GS/s on 16 Channels
DN6.225-16
-
The digitizerNETBOX DN6.22x series allows recording of up to 24 channels with sampling rates of up to 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
PCIe Digital Waveform Acquisition with Programmable Threshold - 125 MBit/s Internal Sampling Rate Timing, 125 MBit/s External State Clock
M4I.7710-X8
-
The M4i.77xx-x8 series digital waveform acquisition (logic-analyzer) cards include versions with 32 synchronous channels, either single-ended with programmable threshold levels or differential. The large onboard memory can be segmented to record different waveform sequences. While the M4i.77xx cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum digital acquisition cards. Therefore existing customers can use the same software they developed for a 10 year old 60 MS/s digital input card also for an M4i.77xx series 720 MS/s logic analyzer.
-
Product
NI-9435, ±5 VDC to ±250 VDC/10 VAC to 250 VAC, 4-Channel (Sinking/Sourcing Input), 3 ms C Series Digital Module
779010-01
-
±5 VDC to ±250 VDC/10 VAC to 250 VAC, 4-Channel (Sinking/Sourcing Input), 3 ms C Series Digital Module - The NI‑9435 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel accepts signals from ±5 VDC to ±250 VDC and 10 VAC to 250 VAC; features transient overvoltage protection between the input channels and earth ground; and has an LED that indicates the status. The NI‑9435 is a correlated digital module, so it can perform correlated operations, triggering, and synchronization when installed in a CompactDAQ chassis.
-
Product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 125 MS/ on 2 DAQ Channels and 2 AWG Channels
DN2.816-02
-
The hybridNETBOX DN2.80/81x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 16 bit resolution and is available with sampling rates of 40 MS/s and 125 MS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
Product
High-Speed A/D 8-Bit Digitizers
-
GaGe 8-bit resolution digitizer models divide the input voltage range into 256 different digitization levels with sampling rates at up to 4 GigaSamples per second on 1 channel or 2 GigaSamples per second on 2 channels with input bandwidths of up to 1.5 GHz, deep onboard sample memory up to 16 GS (16 GB), and true ENOBs of up to 7.6 bits.
-
Product
Digital I/O Vector Development Software
DIOEasy
-
DIOEasy offers test engineers an efficient tool for developing, debugging, and executing digital test vectors for Marvin Test Solutions' GX5050 series, GX5150 series, GX5280 series and GX5291, GX5292, GX5293 and GX5295 dynamic digital instruments.Digital I/O (DIO) systems are very complex and typically require a substantial amount of programming effort to define data vectors. In order to simplify vector development, Marvin Test Solutions developed Windows-based DIOEasy, providing users with an easy to use interface. Toolbars and menus provide quick access to vector editing and viewing tools.
-
Product
PCI-4070, 6½-Digit, ±300 V, 1.8 MS/s Isolated Digitizer Included, PCI Digital Multimeter Device
778275-01
-
The PCI‑4070 is a high-performance DMM that provides the measurement capabilities found in two common test instruments: a high-resolution DMM and a digitizer. As a DMM, the PCI‑4070 delivers fast, accurate AC/DC voltage, AC/DC current, 2‑ or 4‑wire resistance, and frequency/period measurements, as well as diode tests. In the high-voltage, isolated digitizer mode, the PCI‑4070 can acquire waveforms at sample rates up to 1.8 MS/s.
-
Product
NI-6581B, 100 MHz, 54 Single-Ended-Channel, Kintex-7 FPGA-Support, Digital I/O Adapter Module for FlexRIO
783887-01
-
100 MHz, 54 Single-Ended-Channel, Kintex-7 FPGA-Support, Digital I/O Adapter Module for FlexRIO—The NI-6581B is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 54 single-ended digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6581B can operate sample digital waveforms at up to 100 MHz. It includes support for common transistor-to-transistor logic (TTL) voltage levels, or other voltage references can be sourced externally using a front panel connector.
-
Product
PCIe-7820, Kintex 7 160T FPGA Digital Reconfigurable I/O Device
785361-01
-
The PCIe‑7820 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PCIe‑7820 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware-in-the-loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
Product
Synchro to Digital-Resolver to Digital Converters
SDC-RDC 20
-
Computer Conversions Corporation
SDC & RDC 20 BIT Synchro / Resolver to Digital Converter
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 40 MS/s on 8 Channels, 8 Single-Ended Inputs
DN2.593-08
-
The digitizerNETBOX DN2.59x series allows recording of one, two, four, eight or 16 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
