Analog Input Output
Analog I/O are Devices that have the capability of sending and receiving analog signals.
-
product
Analog RF Slot Downconverter: 2000-2400 MHz Input
Model 8111-005
The Bandit® Model 8111 provides a series of high-performance, stand-alone analog RF slot downconverter modules. Packaged in a small, shielded enclosure with connectors for easy integration into RF systems, the modules offer programmable gain, high dynamic range and a low noise figure.
-
product
PCI 12-Bit Analog Output Cards
PCI-DA12-2/4/6 & PCI-DA12-8/16
PCI-DA12-8 and PCI-DA12-16 are full-size cards that can be installed in long slots of PCI-Bus computers. They contain eight and sixteen independent double-buffered, digital-to-analog converters (DACs), and three 16-bit counter/timers.
-
product
sbRIO-9223, Non-Enclosed, ±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
785480-01
Non-Enclosed, ±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The sbRIO-9223 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The sbRIO-92233 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the sbRIO-9223: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
product
Analog Output Expansion Board
MSXB 032
The MSXB 032 Analog Output Expansion Board converts digital inputs from a Data Acquisition Processor into four separate analog outputs. Up to 16 Analog Output Expansion Boards can be connected to a Data Acquisition Processor for a maximum expansion of 64 analog output channels. The MSXB 032 is compatible with Microstar Laboratories Industrial Enclosures.
-
product
Analog Input Module
PMC341
These modules have sixteen analog inputs which are sampled as two eight-channel banks. Eight A/D converters (ADCs) permit simultaneous conversion of all eight channels in a bank. All 16 channels share two generous 512-sample memory buffers. Conversion of each bank requires only 8µS, and all 16 channels can be sampled in just 16µs.
-
product
Analog I/O module with 32/16 multiplexed analog input channels
IO102
Fast 16-bit analog module with 32/16 multiplexed analog input channels and 4 analog output channels. This I/O module offers lower input sampling and conversion times than the IO101 and therefore leads to smaller overall driver latency time. It is similarly priced as the IO101 but comes with 4 analog outputs instead of 8.
-
product
Analog Output Board with Arbitrary Waveform Generation
104-DA12-8A
Model 104-DA12-8A is a PC104 board featuring eight independent 12-bit digital-to-analog converters (DACs) and broadly configurable arbitrary waveform generation (ARB) capabilities. Other convenient features include 128K SRAM for waveform data storage, eight 4-20mA current sinks, three 16-bit counter/timers and fused general-purpose +5V and +12V power outputs. An economy version is available without the ARB feature as model 104-DA12-8.
-
product
16-CH Discrete Input 16-CH Discrete Output Module
HSL-DI16DO16-M-NN
- Input voltage: ±40 V (Max)- Output switching capacity: Single channel 500 mA; all channels 60 mA at 24 VDC- Photo couple isolation voltage: 2500 Vrms- Input impedance: 4.7 KΩ- Input current: ±10 mA (Max) , ±12.5 mA (Peak)- 16-CH digital input and 16-CH digital output. "NN" type for NPN sinking type sensor input or dry contact and NPN sinking type output- Slave ID consumption: 1
-
product
Current / Voltage input Panel meter with output options
DM3420
The DM3420 panel meter accepts Voltage and Current process signals and displays the process value on a high efficiency daylight readable LED display. A built in transmitter power supply is also provided.
-
product
16 Channel, 12-Bit Analog Input PCI Card
PCI-AI12-16A
Model PCI-AI12-16 is a multifunction, high-speed, analog-to-digital converter board for use in PCI-Bus computers. It accepts up to 16 single-ended or eight differential inputs. The board uses a low-noise, multilayer printed circuit board. Inputs are protected against overvoltage conditions up to ±35 volts and typically survive static discharges beyond 4000 volts.
-
product
Input Output Audio Driver Controller
Input and Output Audio Driver Controller. A Handy tool to controll the In-Output Audio Drivers. If you have more than one Soundcard installed on your computer it is a easy way to see all the inputs of your Soundcards. To check all your Outputs, you can run the internal audio file to check the correct left and right channels. It is a must when you have more than 2 soundcards on your computer installed. Freeware or Donate some small money.
-
product
Digital Input / Output Data Acquisition (DAQ) Products
In many cases, we only need to know a simple status about the device we are trying to collect data from, whether something is true or false, on or off, in one position or another. In these cases, we can determine what we need to know using a digital input, or control these things by a digital output. Digital I/O can fit into many applications.
-
product
sbRIO-9220, Non-Enclosed, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 16-Channel C Series Voltage Input Module
787814-01
Non-Enclosed, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 16-Channel C Series Voltage Input Module - The sbRIO‑9220 helps you perform differential analog input. The sbRIO‑9220 contains NIST‑traceable calibration, a channel‑to‑earth ground double isolation barrier for safety and … noise immunity, and high common-mode voltage range. Non-enclosed modules are designed for OEM applications.
-
product
PCI Bus Analog Output Board, 8 Isolated Outputs, 14 Bit, Custom Version
APCI-3501-8-2P
*"-2P" indicates custom version*8 analog output channels, 14-bit*Optical isolation 500 V*4 digital Input*4 digital output*24 V, optically isolated*Watchdog
-
product
256 Channel Digital Input / Interrupt Output Module
DP-VXI-3099
DP-VXI-3099 is a high density module that provides 256 channels of digital input/interrupt and/or output for large scale digital input monitoring and control.
-
product
Analog Input Expansion Termination Board
MSXB 024
Analog Input Expansion Termination Board expands 8 analog input lines to 32 analog input lines and provides connection points for each line. Each of the two models has an onboard temperature reference sensor for cold junction compensation.
-
product
Isolated Analog Input Expansion Board
MSXB 084
The MSXB 084 Isolated Analog Input Expansion Board provides isolated analog inputs for DAP systems. Use these boards to eliminate ground currents – a potential source of noise in your measurement and control signals – and eliminate timing skew.
-
product
Analog & Analog Pwr.
*2 inputs 0-10V or 4-20mA*Possibility of triggering the measurement via 2 dedicated inputs*Local and remote configuration*Consumption controlled for optimized autonomy*Develop new preventive maintenance services, alerts and analyzes.
-
product
8 SE Or 4 Diff. Input Channels, 8 Analog Output Channels, PCI Express
APCIE-3121-8-8
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
High-Speed Analog Output
High-speed analog output photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a PIN photodiode and high-speed amplifier transistor on the output side in a single chip.
-
product
64-Channel VME Analog Input Module
V230
The V230 provides high channel-count data acquisition for dense monitoring applications. The 64 channels are individually programmable for both input range and filtering. The three input ranges slightly exceed ±10 V, ±1 V, and ±100 mV, allowing confident measurements all the way to the end of common signaling ranges.
-
product
C Series Current Input Module
The C Series Current Input Module features programmable input ranges, variable connectivity options, and built-in noise rejection. You can also choose from options with built-in anti-aliasing filters or high-channel density to reduce the number of modules needed. The C Series Current Input Module supports safety features, certifications, input ranges, overvoltage ranges, and connectivity for applications such as power quality monitoring and metering, utility pole-mounted smart switches, utility pole-mounted smart grid reclosers, substation merging units, industrial machine measurements, health monitoring, predictive maintenance and prognostics, and phasor measurement units (PMUs). The C Series Current Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
Analog Input Modules
The modules provide direct connection to a wide variety of sensors and annunciators. They perform all signal conditioning and linearization and contain no pots or DIP switches. All user-selectable settings, such as ranges are stored in nonvolatile EEPROM, which maintains these values even after power is removed.
-
product
Switched Amplifier With Analog Detector Output
Operates at 3 GHz-10 to -5 dBm Input Power to +4 to +7 Output powerAnalog Detector OutputTTL Compatible, 70 dB On-to-Off Ratio, 50 ηSec Response Integrated RF Switch
-
product
REM-11120, 4-Channel Thermocouple, 1-Channel Voltage, Temperature Input Module for Remote I/O
784750-01
4-Channel Thermocouple, 1-Channel Voltage, Temperature Input Module for Remote I/O - The REM‑11120 is a temperature input module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11120 from a real-time controller such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. The REM‑11120 also has an adjustable filter time for improved measurement quality and optional external cold junction compensation (CJC) or PT100 resistance temperature detector (RTD) measurements.
-
product
8 SE Or 4 Diff. Input Channels, 4 Analog Output Channels, PCI Express
APCIE-3121-8-4
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
NI-9246, 50 kS/s/ch, 20 Arms, 30 Apk, 24-Bit, 3-Channel C Series Current Input Module
783920-01
50 kS/s/ch, 20 Arms, 30 Apk, 24-Bit, 3-Channel C Series Current Input Module - The NI‑9246 is designed to support direct ring lug connectivity to the three-phase high-current measurements of 1 A and 5 A current transformers (CTs). It is optimized for power, energy, and industrial applications. The safety features, certifications, input ranges, overvoltage ranges, and connectivity are well suited for applications such as power quality monitoring and metering, utility pole-mounted smart switches, utility pole-mounted smart grid reclosers, substation merging units, industrial machine measurements, health monitoring, predictive maintenance and prognostics, and phasor measurement units (PMUs).
-
product
Isolated Digital Input and Relay Output Card
104-IIRO-8
The 104-IIRO-8 is a low-cost card that provides isolated input and output for PC/104 Bus computer applications. The card has eight optically-isolated digital inputs for AC or DC control signals, eight TTL Inputs and eight electro-mechanical relay outputs. An Economy version can be ordered as Model 104-IIRO-8E which has no Change of State Detection or IRQs.
-
product
96 Channel Isolated Digital Input / Interrupt Output Module
DP-cPCI-3096
96 Channel Isolated Digital Input / Interrupt Output Module
-
product
Analog Oscilloscope
PS-505
*50MHz Vert. Band width*Dual & Trace, ALT Trigger, Z-Input, Y-output*1mV/DIV Sensitivity*10ns/DIV Resolution
