AC Electronic Loads
Simulate voltage, current and power ranges.
-
product
Load Cell Indicator
9840
The 9840 is suitable for use in calibration labs, field service, or anywhere high accuracy is important. Features include a bipolar 6-digit 2-line display, remote sense, low noise, 22-bit resolution, USB port with RS232 communication, mV/V calibration and the ability to store up to 25 different sensors. 6-point linearization, unit conversion, front-panel tare. Self calibration via TEDS Plug & Play ready IEEE1451.4 compliance.
-
product
Load Cabinet
DFX-20
• Working power: AC220V 50Hz • Normal load: Continuous adjustable from 0 to 280V • Electric current: 0～20A/Continuos adjustable cosφ: 0.3-0.96 under 16A; 0.6~0.96 more than 16A • Precision: 0.5 class, digital display • Counter: 0～999999 times, can be preset
-
product
DC Electronic Load
EE30141A
The EE30141A DC Electronic Load / Works @ 0.0 Volts Input & real time I/O control. attach the electronic load block to a heat- sink and your up and running. used them with D to A's, A to D's, Pots, PLC's to control the current. These Electronic Loads can be used for both Discharge & Charging Batteries & Devices
-
-
product
Electronic Printers
EP-100/EP-110
Easy-to-Use Printers, Supporting Good Laboratory Practice The EP-100 and EP-110 electronic printers for Shimadzu balances are easy-to-use, provide time and signature information, and support Good Laboratory Practice (GLP). Supported balance models include: AP; AW-D, AUW, AUX and AUY; ATX and ATY; AT-R; UP; UW and UX; TX; TXB; BL; ELB; BW-K and BX-K; and the MOC63u moisture balance.
-
product
Load Tests
For the production and quality assurance of electric motors and electric drive systems, the use of flexible and customer-specific testing technology is required. Vogelsang & Benning supplies the same to the needs and the application of the customer.
-
product
4500~6000W DC Electronic Loads
JT634 Series
Nanjing Jartul Electronic Co., Ltd
JT634 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT634 series load very suitable for testing power supply when produced in large quantity. Besides, JT634 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT634 series load satisfing most of R&D requirements. Moreover, JT634 series load’s special parallel operation method can satisfy the synchronous loading requirements of multi-channels output power supply and satisfy single-channel output power supply requirement for big power.
-
product
Load Test Software
TW-3.0
The TW-3.0 Load Test software from DLM is a software platform designed to complementDLM’s TW-3.0 range of products within the lifting industry. Used as a tool for assisting therecording of test results and generation of certificates during a load test, the software is able to be loaded onto a Windows PC and accept the output from a TW-3.0 handheld display.
-
product
Transformer Load Box
FY-H / 645
Wuhan Huatian Electric Power Automation Co., Ltd.
When testing current and voltage transformer, it provides various useful loads, which is an ideal matching product for various transformer verification devices.
-
product
Battery Load Tester
BT-100
Schumacher Electric Corporation
FOR EVERYDAY DIY USEEasy to operateTest load, battery condition, starter motor draw and complete charging system diagnosis.Works on 6 and 12 volt batteries50 amp load test for 6 volt batteries100 amp load test for 12 volt batteries Tests 6 and 12 volt batteries ─ up to 1000 CCATop-mounted rocker switch for easier operationSuper-grip, heavy-duty color-coded battery clampsEasy-to-read meter ─ accurate and shock resistantBaked enamel, steel case ─ ventilated to keep coolRubber insulated carrying handle ─ for comfort and safety
-
product
48V / 250 Amp Load
BD15-48P
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
product
DC Load Bank
K-900
Kongter Test & Measurement Co., Limited
K-900 series are your best choice DC load bank with Kongter’s updated solutions. This new series resistive dummy load includes a series customized load bank models that feature rugged design and and excellent performance. They facilitate your work for DC load and battery capacity testing. With different models of DC load bank, it covers a wide range from 12V to 480V nominal voltages with current up to 600A. Its big TFT touch screen with vivid display makes it more user-friendly for setting and operation. Kongter’s new PC software make it easy for measurement monitoring and report print out.
-
product
Electronic Circular Temperature Chart Recorder
The Circular Temperature Chart Recorder’s external stainless steel probe allows you to measure the temperature of air, gas, liquids and semi-solids. The temperature chart recorder has a quartz clock movement, motorized chart advance and temperature accuracy of ±2°F (±1°C). The chart recorder comes in °F or °C models and runs on 120V or 220V AC, 50/60 Hz. A rear compartment houses 8 AA alkaline batteries, providing up to 48 hours of continuous recording in the event of a temporary power loss.
-
product
Canister Load Cells
PCB's cost-effective canister load cells are easy to install and ideal for low-capacity applications. Canister style load cells include a built-in mounting base for a simplified installation in both tension and compression applications.
-
product
110V / 100 Amp Load
BD12-110P
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 110V battery systems and is extremely costeffective.
-
product
AC Insulation Testing
Weshine Electric Manufacturing Co., Ltd
High-voltage Dividers (High Potential Divider) are used to measure voltages and decouple partial discharges in high-voltage test systems. Depending on the specific type, they are used to measure alternating voltage (AC), direct voltage (DC), lightning impulse voltage (LI), and switching impulse voltage (SI) systems. High-voltage dividers by HIGHVOLT comply with the relevant IEC standards. The systems are available for both indoor and outdoor use.
-
product
AC Current Shunts
CSA Series
Ohm-Labs’ CSA series of ac current shunts are designed as laboratory standards for ac current measurement up to high frequencies.
-
product
AC and DC Current Sources
Programmable AC and DC current sources that provide precise, low noise, stable currents for a number of applications.
-
product
Absolute Contamination Standards (ACS)
The Absolute Contamination Standard (ACS) is used to calibrate instruments which size and detect particles on the surface of bare silicon wafers. Use ACS to characterize particles, before particles characterize products.
-
product
AC Power Calibrator
LS3300
The LS3300 is an AC signal generator capable of outputting both current and voltage simultaneously, thus allowing it to calibrate power meters. Providing output ranges of 10mV-1250V, and 0.3 mA to 62.5 A, and upto 78.125 kW, the unit is capable of calibrating up to 0.15 % Class Power meters. New features on the LS3300 include a high definition LCD display, a vector diagram, and the ability to synchronize up to three units to emulate anything from single phase two wire to three phase four wire systems.
-
product
Electronic Crockmeter
TESTEX Testing Equipment Systems Ltd.
Electronic Crockmeter, to determine the colour fastness of textiles to dry or wet rubbing. A pinned acrylic sample holder ensures rapid sample mounting and repeatability of results. Crockmeter Fitted with a pre-determined electronic counter for strokes up to 999,999 times.
-
product
AC Ground Bond Tester
448
Our 448 model is a 4-in-1 tester with 500VA AC Hipot, DC Hipot, Insulation Resistance and Ground Bond testing capabilities. The 448 is capable of a 500VA AC Hipot output to comply with 100mA leakage current test compliance requirements. This tester features a simple design and easy-to-use interface, reducing setup time and increasing production-line throughput for your application.
-
product
Scanning Electron Microscopy
SEM
Materials Evaluation and Engineering
JEOL JSM-6610 LV LaboratoryScanning electron microscopy (SEM) uses electrons for imaging to obtain higher magnifications and greater depth of field than light microscopes. The instruments at MEE are capable of variable-pressure, or low vacuum, SEM (VPSEM), as well as traditional high-vacuum conditions for sample observation. VPSEM is a specialized method using a variable-pressure sample chamber that allows direct evaluation of samples that are not readily examined with a traditional high-vacuum SEM. Nonconductive or vacuum sensitive samples that would typically require additional sample preparation can be directly analyzed in VPSEM without the need for additional sample preparation, such as carbon or metallic conductive coatings. This reduces both sample preparation time and distractions in microanalysis. Our laboratory also has a field emission SEM (FESEM) for critical high-magnification work and low-voltage (LVSEM) applications. Each instrument has a spacious sample chamber that can accommodate large and irregularly-shaped specimens and accessories for feature dimensional analysis and chemical microanalysis.
-
product
AC Power Measurement and Logging
WattNode® Logger for LonWorks®
Continental Control Systems LLC
The WattNode Logger is a kilowatt hour (kWh) energy meter that communicates on a LonWorks network, and can log 24,000+ measurement records in non-volatile memory. The WattNode Logger measures 1, 2, or 3 phases with voltages from 120 to 600 volts alternating current (Vac) and 5 to 6,000 amps in delta (phase to phase) and wye (phase to neutral) configurations.
-
product
Battery Extra Load Units
BXL Series
BXL is an extra load unit designed to be used with DV Power’s BLU series battery testers. However, this unit is a universal add-on device. Because of that, it is compatible, as an additional load, with any other discharge/capacity tester in the market.In case when discharge current exceeds the capacity of a single BLU device, BXL can increase the discharge capacity. There are no limitations on the number of extra load units that can be connected in parallel to the main battery tester.A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way. Also, all instruments are in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.These units can be used on any type of battery string, such as lead-acid, Li-Ion, Ni-Cd, etc. They test battery strings with voltages in the range of 5,25 – 500 V DC. On the other hand, current up to 250 A can be discharged through the BXL internal structure.The instrument simulates a constant resistance load during the discharge test. Several resistances can be set for different battery nominal voltage levels. This makes BXL extremely flexible in selecting its load capabilities.
-
product
AC Leakage Current Tester
229-2
Testing for dangerous small leakage currents is easy with the Simpson Model 229-2 Leakage Current Tester. For use in appliance field service, in the lab, or in production, the 229-2 approximates the human threshold of perception in detecting hazardous AC leakage current. The 229-2 comes with test leads with alligator clips, manual and batteries.
-
product
Load Cells
Applied Weighing International Limited
Range of tension load cells are suitable for smaller Silo, vessel and tank weighing applications. The load cell can be supplied as a fully welded stainless steel or tool steel. Capacities from 1000kg to 5000kg Fitting options available including threaded bar, rod end bearing and eyebolts. ATEX option available.
-
product
AC Relays
The E-MAX ATR and ACV Relays are the AC equivalents of the industry standard E-MAX TIR Trip Indication Relays and AVR Auxiliary Voltage Relays. While the TIR and AVR Relays are designed for use in DC trip circuits, the ATR and ACV are designed for use in AC trip circuits. The relay outputs may be used to record breaker, relay, communication and control system operations, and to activate alarm and/or annunciator contacts. Relays do not require standby power to operate; they are powered by their inputs.
-
product
Unclamped Inductive Load Tester
ITC55600C
Model ITC55350 is the high current (600A) version of theITC55100 tester. The ITC55350 performs the same testsas the ITC55100 and includes many features that improvetesting accuracy, test results collection, test resultsviewing, and multiple tester networking
-
product
DC Electronic Loads
Electronic Test & Power Systems
An adjustable electronic load gives the test engineer the ability to qualify designs, check production batches or service and repair electrical products. Many applications demand an adjustable electronic load. These include the burn-in of new devices along with general power supply, battery, fuel cell and generator testing.
