Up Converters
Increase the frequency of a signal.
-
Product
Modbus to DeviceNet Converter
D485
-
The D485 Modbus to DeviceNet Converter acts as a gateway between a Modbus RTU network and a DeviceNet network. Integration of Modbus devices into DeviceNet networks is enabled without loss of functionality, control, and reliability, both when retrofitting to existing equipment as well as when setting up new installations.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 125 MS/s on 1 Channel, High Voltage Outputs
M2P.6570-X4
-
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
Multifunction Unit - Up to 80 Channels of Digital I/O for Observing and/or Recording 16 to 64 Channels of Pressure of Temperature
Trig-Tek™ 260B
-
Delivers up to 80 channels of digital I/O for observing and/or recording 16 to 64 channels of pressure or temperature. Consists of a motherboard that connects up to four daughterboards to the IP 1553 serial bus.
-
Product
Protocol Converter
MACC
-
When designing or upgrading avionics systems we are often faced with the task of integrating components that were not originally designed to work together.A control computer that communicates using RS-232 may need to control component that expects MIL-STD-1553 messages or an INS may put out ARINC-429 labels, which are needed by Multi function Display designed around RS-422.Faced with problems like these, integrators must choose between two poor options. They must either give up on one of the units in favor of another unit that may be less suitable but uses the appropriate communications spec; or they must add a computer system – often PC104 – which can translate from one unit to the other. These computers are generally large, heavy, hot, and require substantial power.
-
Product
START-1000 Start/run Up Time Test System
-
Hangzhou Everfine Photo-E-Info Co., LTD
Start-1000 can be used to record the start rise time and waveform of the light source in real time, and according to the design requirements of the EU directive 1194/2012, Energy Star and the international standard IEC60969, etc., it is specially used for LED lights, lamps and energy-saving lamps. And it can also be used to measure the photometry parameters of stable light sources.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 625 MS/s on 4 Channels
M4I.6622-X8
-
The M4i.66xx-x8 series arbitrary waveform generators (AWG) deliver the highest performance in both speed and resolution. The series includes PCIe cards with either one, two or four synchronous channels. The large onboard memory can be segmented to replay different waveform sequences. The AWG features a PCI Express x8 Gen 2 interface that offers outstanding data streaming performance. The interface and Spectrum’s optimized drivers enable data transfer rates in excess of 2.8 GB/s so that signals can continuously replayed at a high output rate. While the cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum waveform generators. So, existing customers can use the same software they developed for a 10 year old 20 MS/s AWG card and for an M4i series 625 MS/s AWG.
-
Product
Near Field Probes 30 MHz up to 3 GHz
RF1 set
-
The RF1 near field probe set consists of 4 passive near field probes for making measurements in the development phase of E-field and magnetic field in the ranges of 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF1 set allow for measurements close to the electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors in order to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
Product
Serial Converters And Repeaters
-
With industrial-grade features and specifications, these serial products provide reliable data communication in the most demanding C1/D2 environments.
-
Product
Millimeter Wave Converter
ZVA-Z Series
-
Millimeter-wave measurements in the V, E, W, F, D, G, J and Y band – network analysis in frequency ranges from 50 GHz to 500 GHz depending on the converter model. Featuring a wide dynamic range, the RPG converters offer high operating convenience and allow fast measurements. Two-port measurements can be performed using a four-port network analyzer and two converters; no external generator is required. When using a two-port network analyzer, an external generator is needed to supply the LO signals.
-
Product
6 All-Hybrid Slot 3U PXIe Chassis; AC Powered with Up to 8GB/s System Bandwidth
PXES-2301
-
The ADLINK PXES-2301 compact 6-slot PXI Express chassis, compliant with PXI Express and cPCI Express specifications, provides one system slot with three expansion slots and five hybrid peripheral slots, supporting a wide variety of enhanced-bandwidth testing and measurement applications. The hybrid-slot design accepts installation of CompactPCI, PXI, CompactPCI Express, and PXI Express modules in any peripheral slot for maximum flexibility. Built on a four-link PXI Express chassis with 8GB/s system bandwidth, the PXES-2301's peripheral slots are all connected with PCIe gen2 x4, with slot bandwidth up to 2GB/s. The PXES-2301 implements a smart system monitoring controller, reporting full chassis status including fan speed, system voltages, and internal temperature.
-
Product
Analytical Gear Inspection Machine for Workpieces Up to Ø 6,000 mm
KNM X series
-
machine structure with outstanding intrinsic accuracylarge bearing distances of guidesinherently stable granite machine base on active dampers to absorb vibrations ? no foundation requireddrive system close to center of gravitylinear motors in X-, Y-, Z- measuring axeshigh precision air- or hydrostatic bearing rotary tables (diameters from 500 to 1,800 mm) with direct drive and through holemotorized positioning of measuring column (V-axis) to the actual workpiece diameterlaser based system for safe operation
-
Product
Miniature Airborne Communications Converter
MACC II - Converter
-
Excalibur’s MACC II represents a third option. A proven, low risk, low cost, off the shelf product that translates between different communications specifications. The MACC II can solve your communications problems without R&D costs and without schedule risks while still providing you with the flexibility to customize the system to your specific needs.The MACC II is a wholly contained Miniature Airborne Communications Converter (data converter - protocol converter or translator). The MACC II can carry up to 4 modules. Each module can be one of the following protocols: 1 dual redundant MIL-STD-1553/1760 interface1 H009 channel5 MMSI channels5 ARINC-429 channels2 ARINC-708 channels2 ARINC-717 channels5 ARINC-825 (canbus) channels2 Serial channels (RS-232/422/485, NMEA 0183)Ethernet (10/100/Gigabit)10 Discrete I/O signalsAnalog to Digital / Digital to AnalogPlease see multi protocol 8000 modules for additional information on protocols that can be used on the MACC II.
-
Product
Modulation Distortion Up To 43.5 GHz
S930704B
-
S930704B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 43.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930704B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Industrial Media Converters
-
Advantech's industrial media converters can convert Ethernet data and power into fiber optic signals. They also offer Link Fault Pass-Through (LFPT).
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 125 MS/s on 4 Channels
M2P.6566-X4
-
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
PXIe-1085, 18-Slot (16 Hybrid Slots, 1 PXIe Timing Slot), Up to 24 GB/s PXI Chassis
781813-01
-
PXIe, 18-Slot (16 Hybrid Slots, 1 PXIe Timing Slot), Up to 24 GB/s PXI Chassis—The PXIe‑1085 features a high-bandwidth, all-hybrid backplane to meet a wide range of high-performance test and measurement application needs. The hybrid connector type in every peripheral slot enables the most flexibility in terms of instrumentation module placement.
-
Product
Active broadband antenna up to 6GHz
Series HyperLOG ® 70 X
-
Compatible with any Spectrum Analyzer or Oscilloscope. Incl. High-End Preamplifier. Ultra high gain (44dBi). The HyperLOG X LogPer antenna series can be used to locate extremely weak signals, thanks to the integrated preamplifier. The antenna offers excellent directional characteristics which can be optimized using theoptional Laser and Compass.
-
Product
PWM to Voltage Output D/A Converters
-
Analog Devices’ pulse-width modulation (PWM) to voltage output D/A converters convert a PWM input to an accurate, stable, buffered voltage without the ripple, slow settling, and external passive components of discrete filter implementations. Our PWM D/A converters measure the period and pulse width of a PWM input signal and immediately update the D/A converter output with up to 12-bit accuracy and no software coding required. This family of D/A converters is available with 8-bit to 12-bit resolution, dual and quad channels, integrated references, and with high temperature operation. Applications include isolated motor control, automotive headlights or industrial lighting, and other applications that benefit from the simple control interface.
-
Product
Adapters & Pin Converters
-
Need to adapt your emulator's JTAG connection? We have a variety of pin converters to help connect your debug probe to your target board's JTAG connection, such as TI, MIPI, ARM, and Cortex.
-
Product
Ethernet Bridge Converter for MIL-STD-1553 and ARINC
ENETX-MA4
-
eNetX-MA4™ is an innovative product for “remoting” 1553 & ARINC-429/717 operations on 10/100/1000 Ethernet local area networks (LAN). eNetX-MA4 is a very small, low-power, rugged device that provides real-time UDP connectivity to for 1-2 dual redundant 1553 (A/B) busses and 4 ARINC channels. Tested to MIL-STD-704F/810G/461F and DO160.
-
Product
DC/DC Converter 3.5 W
REM3.5E-2424S/R6/A/SMD
-
DC/DC converter with 3.5 W from Recom | input ranges 18 - 36 VDC | output 24 V | operates in ambient temperature from -40 to +95 °C | SMT package
-
Product
DC toDC Converters
-
Low Cost Single Dual and Triple outputs Isolated Outputs Low Ripple, Regulated Outputs Standard packages and pin outs Custom Designs availableNew Miniature V3 Series features HighVoltage Isolation, SIP and DIP packages
-
Product
High Frequency LCR Meters Up To 30MHz
Chroma 11050
-
Chroma Systems Solutions, Inc.
Measurement capabilities cover the primary and secondary parameters required for testing the inductance, capacitance, resistance, quality factor and loss factor of passive components
-
Product
Ethernet/LXI generatorNETBOX 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 24 Channels
DN6.653-24
-
The generatorNETBOX DN6.65x arbitrary waveform generators (AWG) is a general purpose multi-channel AWG with outstanding dynamic performance. The series includes LXI units with either up to 48 synchronous channels. The large onboard memory can be segmented to replay different waveform sequences.
-
Product
Converter Signal Amplifier – 0…10 Vdc – Wall Mounting
HD978TR6
-
Configurable converter signal amplifier with 0…10 Vdc (10…0 Vdc). Input measuring range -10 ..+60 mVdc. Standard configuration 0…20 mVdc. Minimum measuring range 2 mVdc.
-
Product
DC/DC Converter 2 W
REM2-153.3D
-
DC/DC converter 2 W from Recom | input ranges 13.5 - 16.5 VDC | outputs +/-3.3 V | operates in ambient temperature from -40 to +95 °C
-
Product
Interface Converter
ZET 7076
-
Previously it was widely thought that it is enough to receive sensor readings and to have remote control over them. But gradually there evolved a need for remote control, i.e. people need to receive sensors readings and to control their performance via Internet (for instance, on a portable device). Such possibility simplifies quite a lot of tasks since one can control performance of a system located at the other end of the city or even a country.
-
Product
Mini PoE+ Media Converter, 1000Mbps, SFP (Also Known As MiniMc 857-11911TG)
IMC-390-SFP
-
Supports IEEE802.3at PoE+ (25.5W) and IEEE802.3af PoE (15.4W) standardsServes as a power sourcing equipment (PSE) deviceSupports jumbo frame functionality (up to 10240 bytes)Supports multiple mounting options (desktop, DIN rail or wall-mount)Features in configurable PoE reset on fiber LOSSupports Link Fault Pass Through (LFPT)
-
Product
DC-Angle to Synchro or Resolver Converters
LDS & LDR
-
Computer Conversions Corporation
The LDS 500M Series are high accuracy, drift free, and continuously updating DC-Angle to Synchro or Resolver Converters designed for Military and Industrial simulation and control applications.
-
Product
Four Slot PXI/PXIe Full Hybrid ABex Chassis with up to PXIe x4 Connectivity on Each Slot
ABex PXIe Rack 04
-
Ultra-Compact 2U ABex chassis with 4 slots. This variant is characterized by outstanding compactness and due to the directly integrated PXIe full hybrid backplane one achieves maximum performance at an attractive price. The first slot is reserved for a single slot PXIe controller. Either Konrad PXIe embedded controllers or MXI interfaces are supported.
