Bare Board Testers
check unloaded PCBs for opens, shorts, leakage and voltage breakdown.
See Also: Bare Board, Bare Board Test, Bare Board Probes, Bare board Fixtures, PCB
-
Product
ESD Tester
GZ600 MIF
-
• Staff equipment tester with badge reader • Compact • LCD digital display • Identification by RFID badge • Allows communication with the company network or the dedicated server (SQL database)
-
Product
Serial I/O Boards
-
Serial Mode Protocols include Asynchronous, Bisync, SDLC, HDLC, IEEE 802.3, Synchronous Telemetry, Simple Clock/Data ("-SYNC" product line), Di-phase and SPI Interface. Transceiver support RS485, RS422 (V.10), RS232 (V.28), RS423, V.35, RS530, as well as other software selectable mixed protocol modes Up to Eight Independent Serial Channels per Board Synchronous Serial Data Rates up to 10 Mbits/sec Asynchronous Serial Data Rates up to 1 Mbits/sec PMC and cPCI rear I/O support Custom Protocols Available
-
Product
Oscilloscope Tester
ScopeTester 5
-
ScopeTester 5 is 5-channel oscilloscope tester for PCs. Unlike traditional oscilloscopes it is capable of continuous acquisition of signals without dead times. This feature gives exceptional diagnostic value. Available voltage ranges matches typical signals found in modern cars. The user may connect to vehicle sensors, actuators and other diagnostic equipment, such as current clamps, inductive and capacitive probes and other diagnostic probes.
-
Product
Insulation Testers
-
Preventive maintenance is always a must, especially in motor instrumentation. Knowing before a problem arises, allows time for scheduled shut downs, instead of shutting your process down when you need it the most. Yokogawa offers many varieties of Insulation testers, from our “Hand Crank” version to our Analog and Digital 1000V versions.
-
Product
Heavy Board & Heavy Board
Protector Lever Actuated Clamshell
-
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
-
Product
Cable Testers
-
Passage test:Detects open wires, short circuits and faulty wiring. Pass / fail test using a given pattern cable. Finding intermittent connections.Save cable data for documentation purposes. Print wiring diagrams. Printing labels. Log and print error logs.Graphical representation of the wiring of cables, graphical comparison of two cables. Easy, intuitive, graphical tracking of individual wires of a cable.Quickly install quick-mount boards for a variety of connector types such as BNC, RJ45, Sub-D, flat-ribbon connectors, and many more.Easy connection to the PC via USB .Light Director System:LED-led assembly of connectors. Optional also with voice output. High degree of safety due to fault checking during assembly.
-
Product
Surge Tester
-
Educated Design & Development, Inc.
An electronic testing device used to evaluate the condition of electrical insulation in coils, transformers, and electric motors.
-
Product
PXI FPGA Board
PXIe-8316-DSP
-
The PXIe-8316-DSP FPGA board is a user programmable hardware platform with an 8-lane Gen3 PXI Express (PXIe) interface. It includes four QSFP ports (16 lanes) to support High Speed Serial (HSS) connections.
-
Product
PCI Digital I/O Boards
PIO-D24U
-
Universal PCI Board with 24 channels of Digital I/O Board. Replacement product for DIO-24.
-
Product
Multipurpose Debug Board For EC
DB30 x86 Debug Module
-
The DB30 x86 Debug Card is designed for debugging of COM Express modules with FFC (FlexFoil Cable) debug connector. It includes an 80 port for Power on and Self-test (POST) via I2C interface, interface to SPI Flash for BIOS update, interface to EC for Embedded Controller (EC) update, Power and Reset buttons, and Status LEDs and Test Point for various debug tests.
-
Product
RELIABILITY BOARD (Reliability Test Board)
-
The reliability test board is used for testing of HAST, THB, HTOL, BURN-IN, etc. It is a product that evaluates the environmental test and durability when applied to actual products such as lifetime test, high temperature, low temperature, high humidity and thermal shock
-
Product
Voltage/Continuity Tester
VOT-52
-
Standard Electric Works Co., Ltd
● Voltage test: 12V to 1000V AC/DC (8 LEDs) with indication by buzzer.● Voltage range: 12V, 24V, 50V, 120V, 230V, 400V, 750V, 1000V.● Test leads positioned at 19mm apart.● Interchangeable probe tip for 2mm and 4mm.● Polarity test : LED +/-● Audible continuity test.● Phase rotation test : /● Self-test button to ensure proper function of the device prior to testing.● Waterproof design, protection class: IP65.● Phase / Neutral identification.● Rubberized double-molded housing.● ELCB / RCD trip test.● Flashlight function.● Safety standard : IEC/EN 61010-1 III 1000V IEC/EN 61010-1 IV 600V IEC/EN 61243-3 EN 61326-1
-
Product
Insulation Tester
AD-2025
-
Measuring voltage control during measurement, Insulation measurement up to 400 G W. Elimination of trough resistance insulation ? 3 connectors measurement method, Autoranging, Auto-Discharge facility safely discharges the connected circuit after a test, 5 minutes, 1 minute at will shorter measurement,
-
Product
Wristat Tester
WT25
-
The WT25 WRISTAT Tester is designed to test the integrity of our WRISTAT in a fast, efficient and simple manner. All of the elements of the WRISTAT - continuity of the strap, integrity of the protective resistor, and satisfactory strap to skin contact are easily confirmed by pressing the top cover of the WT25. The operator (wearer) is tested for a resistance to ground of greater than 750K ohms and less than 10M (switchable to 100M ohms).
-
Product
Socket Tester
-
*Power supply from mains : 200-230V AC*Transmit AC signal through concrete walls; Shielded / armored cable*Internal fuse protection
-
Product
Damp-Heat Tester
-
King Design Industrial Co., Ltd.
1. Technical index:*Power: 380V, 3-, 50/60HZ 110A*Temperature range: 50°C~120°C*Humidity range: 20%~95% RH*Accuracy: 1) temperature ± 0.3°C；2) humidity ± 2.5% RH*Uniformity: 1) temperature ± 2.0°C；2) humidity ± 3.0% RH*Uniformity test: measured at T=85°C, RH=85%; set 9 points for temperature measurement and 2 points for humidity.*Inner wall is above 50 cm; within 20 min after temperature/humidity meets the setting value, the distribution uniformity of temperature/humidity can meet the aforesaid requirement.
-
Product
Pkt2-PCIe and Pkt2-AMC Boards
-
Provide front-end intelligent processing for DPI, IPsec and GTP acceleration, delivering a high-performance, secure, carrier-grade, packet processing for LTE, 3G and IMS networks.
-
Product
Franklin Tester
Model 717
-
The Model 717 Franklin Tester provides a means of testing single strips or punchings of flat rolled electrical steel, for surface insulation resistance under predetermined conditions of voltage and pressure.
-
Product
3U Modular Processor Board
CP32105
-
LinkedHope Intelligent Technologies Co.,Ltd.
Based on Intel® Atom™ Processor, LinkedHope® designs CP32105 in a COMexpress® based modular 3U CompactPCI form factor. CP32105 is compliant with PICMG CompactPCI 2.0 specification, and it is low power, compact and fully integrated.CP32105 offers a variety of processor options from Intel Cedar View family, such as D2550, N2600 and N2800. CP32105 supports onboard SATA FLASH hard disk up to 64GB, which is designed mainly for installing operating system. With excellent anti-shock and anti-vibration performance, CP32105 can be operated stably on train, on ship, and in other special off road vehicles. CP32105 supports WLAN (Wireless Local Area Network) and 3G/4G wireless communication functions, which enable local and remote wireless data exchange easier than ever before.
-
Product
PCI Board
FastX1703-DIG
-
The FastX1703-DIG is a raw-length PCI board with two input connectors. Each connector supports 16 data bits, 10 general purpose inputs, and 6 general purpose outputs. Clock rates up to 166 MHz can be supported. All the inputs and outputs are connected to an FPGA on the board are essentially available for any purpose required by the interface. The front-end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, zero to four Nexperia PNX1702 VLIW processors before output. Finally, the Fast-X-DIG interfaces to the host computer through a 4 x PCIe interface for state-of-the-art data acquisition.
-
Product
LocoNet & Testers
-
The LNRP Xtra LocoNet Repeater Module Isolates and Protects LocoNet Layouts, it allows for greater expansion of the LocoNet system on large installations. The LNRP Xtra allows "protected" sections of LocoNet to continue functioning even when a fault occurs elsewhere, the LNRP Xtra automatically reconnects the faulty section once the issue is resolved. Now includes the PS14 power supply.
-
Product
PCI Daughter Boards
DB-24POR/D (with D-Sub cable)
-
The DB-24POR has 24 channels of optically isolated Photo-Mos Relay , and OPTO-22 compatible connector.
-
Product
Thunderbolt V-600 Board 4-Slot
-
The 6U VME Thunderbolt boards provide optimal performance and reliability. The Thunderbolt V-600, configured with one Compute Module of four MPC7410 processors, provides 16 GFLOPS of computational performance per 6U VME slot. Data is transferred throughout the Thunderbolt over the SKYchannel Packet Bus. Data moves transparently through the SKYchannel P2 interface to other boards in a SKYchannel chassis.
-
Product
BIP Tester
-
BIP TESTER is a measuring device designed for users that already have a unit injector test bench, but their lack reliable BIP measurement.
-
Product
Battery Tester
IT5100 Series
-
IT5100 series is a series of battery internal resistance testers with high precision, high resolution and high speed. IT5100 adopts AC 4-terminal sensing, that means the tester can test internal resistance and voltage simultaneously with high precision. Resistance resolution is down to 0.1 μΩ, voltage resolution is 10 μV.
-
Product
Single Board Computer
VME-1909
-
Curtiss-Wright Defense Solutions
The VME-1909 from Curtiss-Wright Defense Solutions is designed to be a low cost, high performance technology insertion Single Board Computer (SBC). Pin-compatible with many previous generations of Curtiss-Wright SBCs, the VME-1909 offers increased computing performance with today’s latest software advances.
-
Product
Embedded Boards
UltraZed Family
-
Embedded boards are boards with processors, multiple integrated circuits, interfaces and other essential components assembled on it to serve a dedicated function. Embedded boards comprise multiple technologies, including processors, core logic, networking, connectivity, and multimedia components to provide functionality and performance for embedded system design applications. Embedded boards and solutions are normally employed to ensure a faster time to market for the developer. Applications of embedded systems vary from tiny portable devices, to large commercial and industrial installations, and even largely complex systems like medical or military or aviation purposes. Embedded boards can have single MCU chip or multiple MCUs depending on the complexity of application.
-
Product
Relay Testers
-
Outputs 100VA single-phase voltage and 180VA single-phase currentEquipped with counter function, output selector, auto sweep function, memory function, DC output for testing, master/slave function, etc.Output frequencies of 50Hz, 60Hz, and 10Hz to 200Hz, using external synchronization or line synchronization (selectable)Equipped with GPIB/RS-232C interfacesWeight: 19.5kg
-
Product
Signal Conditioner As Circuit Board Module
-
INELTA Sensorsysteme GmbH & Co. KG
For LVDT Displacement Sensors, DMS Force Sensors
-
