Gas Leak Detectors
See Also: Leak Detectors, Gas Leak Detection, Refrigerant Leak Detectors
-
Product
Flame Ionization Detector
-
A flame ionization detector converts a hydrocarbon gas concentration into an electrical signal. The flame is hydrogen fueled and burns in hydrocarbon free combustion air. Either side of the flame are two electrodes between which an electric field is generated by means of a polarization voltage. The sample is pre-mixed with the fuel gas and heated in the flame to a temperature at which the hydrocarbon molecules ‘crack’ and CH fragments appear. These CH fragments are oxidated by the oxygen in the combustion air resulting in the formation of CHO+ ions. The ion current then passes to the electrodes and the resulting current measured is proportional to the quantity of C atoms derived from organic compounds.The Thermo-FID features two separate microprocessor controlled pressure compensations to avoid any influence from environmental or sample conditions. In addition, the complete Thermo-FID range of analyzers are equipped with a flame trap that is used as a heated sample inlet filter. The measurement chamber and all material in contact with the sample gas are heated between 120°C and 200°C to avoid condensation.
-
Product
Solar Radiation Detector PCE-SPM 1
-
PCE-SPM 1 is a photovoltaic (PV) light meter used to measure solar radiation, solar energy or solar power. The meter's easy-to-read 4-digit LCD screen clearly displays Ptot in W/m² or BTU/(ft² x h), while the device's auto data memory stores up to 43,000 data sets.
-
Product
Ultrasonic Flaw Detectors
-
Our full range of portable ultrasonic flaw detectors (UT) provides unmatched capabilities for locating discontinuities and other flaws. A wide range of software options is available for enhanced flaw detector inspection.
-
Product
Detectors
-
Optical detectors provide additional analytical detail about your samples. When paired with their accessories, such as flow cells or nebulizers, you can obtain more information per run, fulfilling multiple detection strategy requirements.
-
Product
Conveyor HotSpot Detectors
-
The transportation of coal on any form of conveyor system has the potential to ignite, with the ultimate outcome being a fire. A single point temperature measurement system can detect a hot spot, but is just as often likely to miss one.
-
Product
Gas Pressure Manometer
1213
-
Provide visual indication of pressure with the Series 1213 Gas Pressure Manometer. Designed for use with natural gas, the manometer can also be used to monitor any compatible gases up to 15 inches of water column
-
Product
Particle Impact Noise Detector
BW-LPD-D4000
-
FREQUENCY: SINE WAVE 27Hz TO 265HzACCELERATION: 0 TO 20G PEAKSHAKER: 100 FORCE LBS 3/4" IN STROKE 75 IN PER/SEC VELOCITYAMPLIFIER: 250 WATTS MINIMUMD.U.T. WEIGHT: 300 GRAMS PRACTICAL LIMIT @ 20G
-
Product
On-Line Gas Analysis System
Titan-OL
-
The Titan-OL is a turnkey, process-ready gas analysis system. The analyzer and sample handling hardware can be wall or frame mounted in a NEMA enclosure suitable for use in production environments, including Class I, Div. 1. The integrated sampling system is fully purgeable and can handle multiple sample and reference lines.
-
Product
UV/IR Flame Detector for Hydrogen Apps
-
The FL500-H2 is an Ultraviolet / Infrared flame detector designed specifically to detect hydrogen (H2) fires. The FL500-H2 optical flame detector monitors for radiation emitted by a hydrogen flame in both the ultraviolet (UV) and infrared (IR) spectral ranges.
-
Product
Heat Detector Testing
Solo 461
-
Functional checking of heat detectors, with a genuine heat source, is now required by major national standards around the world. Testing with heat sources not designed for the purpose can be both dangerous and damaging. The Solo range of heat detector testing equipment, designed specifically for the purpose, provides a genuine professional’s solution.
-
Product
FAult Detector and OScilloscope 9 Functions in 1
FADOS9F1
-
Prot-Ar-Ge Industrial Project Design R&D Ltd. Co.
2 unique features are added to the FADOS9F1 over the FADOS71. First feature is the Programmable DC Power Supply; It can be adjusted between 0-16V and 20-1500mA with power output; the DC Voltage/Current graphs of the electronic card power supply can be produced. The second feature is the “IR Remote Temperature Measurement Sensor”; this sensor is used to find the components that heat up by drawing too much current. Using these two features together may reduce the time for trouble shooting some malfunctions by 5 to 10 times. These features can be used as a new technique for trouble shooting.
-
Product
Laser Open Path H2S Detector
GD1
-
Teledyne Gas & Flame Detection
The GD1 has been designed with features that provide an effective response to the detection of gas hazards in a wide range of industrial environments from offshore production facilities to wastewater treatment plants. At the heart of the detector is a tuneable laser diode that eliminates environmental effects from sun, rain and fog. The laser scans single absorption lines where there is no interference from other gases.The GD1 needs no recalibration and can replace multiple standard detectors to cover the same risk. The complete optomechanical design and construction is so stable that an ultra fast speed of response can be achieved while providing unparalleled service life and detector stability, thus saving on maintenance and service costs.Supplied with worldwide hazardous area approvals. Suitable for use in systems with SIL 2 requirement.
-
Product
Voltage-Pen-Detector
-
Are a relatively simple testing instrument that enables electricians and other uses tolocate, trace and identify common electrical problems. These testers can locate wires behind walls, underground,and inside junction boxes. Others are designed to find blown fuses or test light fixtures. Some testers can evenlocate neutrals, ground faults, and high voltage lines without interrupting power
-
Product
Residual Gas Analyzer
Models XT100, XT200, XT300
-
The XT residual gas analyzer (RGA) from Extorr offers exceptional performance and value. These RGAs provide a more detailed vacuum gas analysis than is offered by any other single competitive device. Each system comes complete with a multi-gauged quadrupole probe, a control and communications unit (CCU), and a real-time Windows software package.
-
Product
Voltage Detectors
JSC
-
The JSC family of devices provides a highly reliable way to determine if voltage is present downstream of the disconnector or circuit breaker knives during zero-energy shutdowns. They dramatically increase the safety of personnel performing maintenance on electrical equipment. When voltage is present downstream of the disconnector knives, one or more LEDs on the JSC-88A will remain illuminated. The JSC's compact design allows for direct installation on the disconnector door, starter, or control panel.
-
Product
Gas Leakage Camera
-
Zhejiang ULIRvisionTechnology Co., LTD
Gas leakage camera is an instrumentation tool for gas leakage detection. Below are two of our featured gas leak cameras.
-
Product
Package Leak Detectors
-
Packages should be absolutely leak tight. However, even with the utmost care in the process, faulty packaged products cannot be completely avoided. Defects in the sealing process or in the material can easily lead to leaks, sometimes microscopically small.
-
Product
Flaw Detectors
-
GAOTek flaw detectors are designed as high-quality devices that provide accurate detection whilst delivering ease of use towards testing and monitoring. These detectors examine a material by passing sound waves at high frequencies through it and are used for applications that require ultrasonic testing. They are compact, easy to carry and portable devices that allow the user to work in complex conditions and circumstances, and available for purchase in the United States, Canada and globally.
-
Product
Methane, Propane and other Hydrocarbon Gas Sensors
-
Hydrocarbon type sensors specially characterised during manufacture to measure Propane (C3H8) gas over the range 0-2% volume.
-
Product
Beam Position Detectors
-
We offer a wide range of laser beam position detectors for optical alignment including Quadrant Cell Photoreceivers, PSDs, and Thermopile Position Sensors. Please see our Beam Position Sensor Guide for more information.
-
Product
Pyroelectric IR Detectors and Sensors
-
Excelitas Pyroelectric Infrared Detectors define the leading edge of motion detection technology, offering a variety of both digital and analog Pyroelectric IR Detectors to serve a wide range of applications in smart home, smart city, IOT, burglary detection and security systems. With Pyroelectrics available in Single-, Dual- and Quad-Element configurations we offer you a wider range of different sized infrared sensor surfaces, which directly translates to enhanced performance and sensitivity. Excelitas sensors are representing the innovative forefront in mid-IR sensor devices. The family of DigiPyros enables smart home and smart sensing applications with low current requirements.
-
Product
Cable Detectors
-
PeakTech Prüf- und Messtechnik GmbH
This cable detector works acoustically and offers a quick and inexpensive solution to find voltage-free lines in the house installation, to test telephone lines, to identify individual cables / wires or to carry out a continuity test.
-
Product
Ultrasonic Optical Flaw Detector
MIV-X
-
Thanks to Shimadzu’s proprietary light imagining technique, which combines an ultrasonic oscillator with a stroboscope, defects near the surface of a material, including peeling of the bonding and adhesive surfaces of heterogeneous materials, as well as paint, thermal sprays, and coatings can be inspected easily and non-destructively.
-
Product
Manual Contactless Wafer Detector
HS-NCS-300
-
Manual, non-contact measurement of wafer thickness, TTV and bow. Portable and easy to set-up, the Proforma 300/G measures all wafer materials including Silicon, Gallium-Arsenide, Indium-Phosphide and wafers mounted to sapphire or tape.
-
Product
Event Detectors
105/106 Series
-
The 105/106 Series Event Detectors are the most versatile Event Detectors in the product line. These Event Detectors monitor the electrical resistance of up to 128 simple continuity loops, each comprised of single or multiple specimens under test. Each test specimen is continuously monitored while a selectable DC sense current is passed through each channel test-loop; resistance changes exceeding the selected threshold are recorded as an event. Minimum Event Duration, Channel Current, and Threshold Voltage settings can all be independently configured. 105 and 106 Series instruments are electrically identical, with the difference simply that the 105 offers four, 32-channel board slots and the 106 offers only one. Thus the 128-105 is equivalent to four 32-106 Event Detectors.
-
Product
Wireless or Stand-Alone CO Detector w/ Sensor Self-Test
COA2
-
UEi Test & Measurement Instruments
Wireless Carbon Monoxide Detector with Self Test
-
Product
Non-Linear Junction Detector
ORION® 2.4 HX
-
The ORION 2.4 HX Non-Linear Junction Detector (NLJD) detects electronic semi-conductor components in walls, floors, ceilings, fixtures, furniture, containers, or other surfaces. The ORION 2.4 HX NLJD is made to detect and locate hidden cameras, microphones, and other electronic devices regardless of whether the surveillance device is radiating, hard wired, or turned off.
-
Product
Fixed Gas Detectors
-
Teledyne Gas & Flame Detection
Are you looking for reliable and efficient fixed gas detectors? Discover our detection devices especially designed for professionals in the industry and in the service sector.
-
Product
Gas Monitor
S5000
-
The General Monitors S5000 Gas Monitor is the ultimate gas detector for extreme environments needing to detect oxygen, toxic and combustible gases.
-
Product
Pulsed DC Holiday Detector Inspection Kit
280
-
The Elcometer 280 Pulsed DC Holiday Detector is a ‘stick type’ holiday detector that has been designed to make pulsed DC high voltage holiday detection safer, easier and more reliable than ever before.
