Fixed Gas Detectors
Teledyne Gas & Flame Detection
Are you looking for reliable and efficient fixed gas detectors? Discover our detection devices especially designed for professionals in the industry and in the service sector.
-
Product
Fixed Gas Detectors
DG7 Series
-
Teledyne Gas & Flame Detection
All DGi-TT7 are constructed from a common housing and electronics with the detection properties being determined by the type of sensor (cartridge) used. A wide range of cells are available, these cells are intrisically safe protected, and may be replaced with the detector powered which minimises the system down time. The intelligent, microprocessor driven unit is fully configurable using a wireless hand-held terminal (TLU) or by using the hard wired HART option giving true flexibility to the installer and reduced service costs.Elements such as relay operation and alarm levels are all set via the TLU, a hazardous area approved hand-held unit. The unit may be interfaced directly with a wide range of panels, controllers and PLC’s etc. Its integral daylight readable alphanumeric display indicates local status and alarm level.
-
Product
Fixed Gas Detectors
700 Series
-
Teledyne Gas & Flame Detection
The sensor electronics are completely protected and immune to water ingress and corrosion. The sensor elements are all plug-in components and can easily be replaced in the field. Operator interface is non-intrusive via a small handheld magnet. Configuration and routine calibration is intuitive and menu driven with fully scripted instructions. Sensor status is displayed on a built-in alphanumeric LED display. The 700 Series intelligent sensor modules feature dual redundant outputs, a linear 4-20 milliamp analog signal and a Modbus RS-485 serial output.
-
Product
Personal Safety Gas Monitors
-
Teledyne Gas & Flame Detection
Want to protect your staff with high-end portable gas detectors? Discover Teledyne Gas and Flame Detection gas detection solutions.
-
Product
Portable Gas Measurement Devices
-
Teledyne Gas & Flame Detection
Looking for portable gas leak detectors to protect your staff? Teledyne Gas and Flame Detection measuring devices meet all your requirements.
-
Product
Fixed Toxic Gas Detector
CTX 300
-
Teledyne Gas & Flame Detection
When hazardous levels of toxic gases or oxygen threaten the safety of an unclassified area, the CTX 300 detector can satisfy the most demanding safety requirements.The CTX 300 detector is designed to detect oxygen, toxic and refrigerant gases, and also uses a new sensor for CO2 detection over three different ranges: 0-5000 ppm, 0-5% vol. and 0-100% vol.The CTX 300 transmits data in record time. With a wide range of sensor options, it has the flexibility to protect many potentially hazardous environments.Maintaining the unit is easy with pre-calibrated sensors and an optional LCD display.
-
Product
Laser Open Path H2S Detector
GD1
-
Teledyne Gas & Flame Detection
The GD1 has been designed with features that provide an effective response to the detection of gas hazards in a wide range of industrial environments from offshore production facilities to wastewater treatment plants. At the heart of the detector is a tuneable laser diode that eliminates environmental effects from sun, rain and fog. The laser scans single absorption lines where there is no interference from other gases.The GD1 needs no recalibration and can replace multiple standard detectors to cover the same risk. The complete optomechanical design and construction is so stable that an ultra fast speed of response can be achieved while providing unparalleled service life and detector stability, thus saving on maintenance and service costs.Supplied with worldwide hazardous area approvals. Suitable for use in systems with SIL 2 requirement.
-
Product
Infrared Gas Detector
GD10 Series
-
Teledyne Gas & Flame Detection
The GD10 Series has been designed with features that provide an effective response to the detection of gas hazards in a wide range of industrial environments from boiler plant rooms to offshore petrochemical installations.These infrared gas detectors differ from all other models, because they utilize silicon based solid-state infrared sources. The complete optomechanical design and construction is so stable that an ultra fast speed of response can be achieved while providing unparalleled service life and detector stability, thus saving on maintenance and service costs.We offer the longest combined detector and IR source warranty on the market.
-
Product
Hazardous Area Gas Detector
Meridian
-
Teledyne Gas & Flame Detection
Whether you need an infrared or catalytic bead sensor to detect combustible gases or an electrochemical sensor for a toxic environment, the Meridian universal gas detector utilizes a single detector head to easily accept all sensor types. There is no requirement for distinct personality boards in the gas detector or different detector heads to make the instrument behave as a combustible or toxic gas detector. The Meridian gas detector accepts all sensor types in one detector. Simply attach the specific toxic or combustible sensor to the universal detector head and the Meridian gas detector will automatically determine the type of gas to be detected. Installation of the sensor is a simple plug-and-play action. At Teledyne Gas and Flame Detection, we are always looking to anticipate your future needs. We designed the Meridian gas detection platform to be future proof, allowing you to take advantage of new sensing technologies from Teledyne Gas and Flame Detection while maintaining ease of use and peace of mind.
-
Product
Fixed Gas Detectors
MicroSafe 500 & 600 Series
-
Teledyne Gas & Flame Detection
MicroSafe 500 and 600 Series gas detectors feature a non-intrusive operator interface. Calibration and programming instructions appear in simple intuitive and sequential script on a 16-character backlit display. The transmitter design incorporates extensive fault diagnostics with each condition conveniently identified on the transmitter display.The 500 Series comes standard with a linear 4-20 mA output, one-man remote calibration, self-adjusting zero and span, and LED indicators for fault and calibration status.The 600 Series includes the same features as the 500 with the addition of 3 alarm relays and an RS-485 serial communications port.Electrical Classification - Explosion proofClass I, Div 1, Groups B, C, D
-
Product
Toxic Gas Sensor
Model 100
-
Teledyne Gas & Flame Detection
Model DM-100 Series sensors feature intelligent electronics, non-intrusive operator interface and comprehensive fault diagnostics. The sensor is packaged in an electro-polished 316 stainless steel housing fitted with a ¾ inch NPT thread. The plug-in, field replaceable sensor cell features large surface area gold-plated pins that reduce the effects of corrosion in harsh industrial environments. Signal conditioning electronics are completely encapsulated in the sensor housing adding a high level of durability to the design. The packaging is XP-intrinsically safe. This innovative design marks a return to a simple, more affordable, and durable gas detection sensor without compromising quality.Model DM-100 sensors provide a 2-wire loop powered 4-20 mA current signal equivalent to the sensor range of detection. Upper enclosure options are aluminum and stainless steel. Additional accessories include wireless communications, a loop powered digital display. Each sensor is shipped with a splash guard with integral calibration port. Detcon’s toxic gas sensors have a long shelf life and are supported by an industry-leading warranty.
-
Product
Fixed Gas Analyzer
Model 1000
-
Teledyne Gas & Flame Detection
Natural gas pipeline monitor to detect H2S and CO2.Detcon Model 1000-CO2 and Model 1000-H2S Analyzers are designed to provide continuous, accurate, real-time measurement of gas concentrations in a wide variety of process gas streams. The instrument package is rated for Non-Hazardous areas.Consult commercial brochures for measurement ranges and more product features.
-
Product
Fixed Gas Detectors
OLCT 10 - OLC 10
-
Teledyne Gas & Flame Detection
The OLC 10 and OLCT 10 are designed to detect combustible or toxic gases for tertiary applications (boiler plants, battery charging rooms, car parks, hospitals). Two OLC 10's can be connected to one detection channel to monitor the same area, without an additional junction box or extra wiring. Similarly, up to five OLCT 10's can be connected to one channel for the detection of CO, NO or NO₂ in a car park application. Easy to install and operate, these detectors combined with the MX 16 control unit meet demanding user requirements.
-
Product
Fixed Digital Gas Detector
OLCT 10N
-
Teledyne Gas & Flame Detection
The OLCT 10N is a digital combustible gas detector designed for to detect combustible, toxic gases or oxygen. Intended for use in combination with the MX 16, MX 32 and MX 43 controller, the OLCT 10N provides a fast and accurate response.All transmitter information is received by the controller in less than 1 second.Non-intrusive operator interface requires only a simple magnetic wand and allows one man calibration without opening the enclosure.
-
Product
Industrial Gas Detector
OLCT 60
-
Teledyne Gas & Flame Detection
The OLCT 60AD version allows the sensor to be installed remotely up to 15 meters (standard), allowing detection in inaccessible locations, or in Zone 0 in the case of the intrinsically safe (IS) version. The detector units are made of 316L stainless steel, and are rugged and resistant to corrosion. Pre-calibrated sensors can be disconnected by turning the head of the unit. These “smart” sensors can be calibrated outside hazardous areas.The OLCT 60 is equipped with non-intrusive access to a safe menu. In hazardous areas, calibration can be done with an operating mode in accordance with safety rules.
-
Product
Fixed Gas Detector
OLCT 80
-
Teledyne Gas & Flame Detection
Oldham is pleased to propose its wireless system with the OLCT 80 field detector/transmitter. This model allows wireless connectivity in ATEX 1 zones.
-
Product
Open Path Combustible Gas Detector
SafEye (Quasar 900)
-
Teledyne Gas & Flame Detection
The Open Path Combustible system detects hydrocarbon gases by analyzing the absorption of radiation caused by gases in the atmosphere and comparing it to background atmospheric absorption. This is accomplished between a pair of units: a Flash Source and a Detector that can monitor a distance of up to 200 meters.Open Path Combustible Gas Detectors are robustly designed and can handle the toughest environments: 316L stainless steel housings that meet IP66/IP68 and NEMA 250 6P egress standards; circuit boards epoxy coated for protection; MIL-C-810C testing for humidity, salt, fog, vibration, mechanical shock and temperature extremes; and SIL-2 approval per IEC61508 is a final statement in reliability.
-
Product
Infrared Gas Detector
iTrans2
-
Teledyne Gas & Flame Detection
The iTrans2 infrared gas detector employs an intelligent electronics platform to provide one or two points of detection from a single head for maximum flexibility, superior performance and lower installation costs. With the optional HART Communication Protocol, the iTrans2 offers remote diagnostics, set-up or calibration by superimposing a high-frequency current across the industry standard 4-20mA analog line.
Filter Products:
-
Product
Fixed Gas Detectors
DG7 Series
-
Teledyne Gas & Flame Detection
All DGi-TT7 are constructed from a common housing and electronics with the detection properties being determined by the type of sensor (cartridge) used. A wide range of cells are available, these cells are intrisically safe protected, and may be replaced with the detector powered which minimises the system down time. The intelligent, microprocessor driven unit is fully configurable using a wireless hand-held terminal (TLU) or by using the hard wired HART option giving true flexibility to the installer and reduced service costs.Elements such as relay operation and alarm levels are all set via the TLU, a hazardous area approved hand-held unit. The unit may be interfaced directly with a wide range of panels, controllers and PLC’s etc. Its integral daylight readable alphanumeric display indicates local status and alarm level.
-
Product
Fixed Gas Detectors
700 Series
-
Teledyne Gas & Flame Detection
The sensor electronics are completely protected and immune to water ingress and corrosion. The sensor elements are all plug-in components and can easily be replaced in the field. Operator interface is non-intrusive via a small handheld magnet. Configuration and routine calibration is intuitive and menu driven with fully scripted instructions. Sensor status is displayed on a built-in alphanumeric LED display. The 700 Series intelligent sensor modules feature dual redundant outputs, a linear 4-20 milliamp analog signal and a Modbus RS-485 serial output.
-
Product
Personal Safety Gas Monitors
-
Teledyne Gas & Flame Detection
Want to protect your staff with high-end portable gas detectors? Discover Teledyne Gas and Flame Detection gas detection solutions.
-
Product
Portable Gas Measurement Devices
-
Teledyne Gas & Flame Detection
Looking for portable gas leak detectors to protect your staff? Teledyne Gas and Flame Detection measuring devices meet all your requirements.
-
Product
Fixed Flame Detectors
-
Teledyne Gas & Flame Detection
Would you like to source high-performance flame detectors? Teledyne Gas and Flame Detection offers detection solutions that precisely meet the needs of the most demanding professionals.
-
Product
Laser Open Path H2S Detector
GD1
-
Teledyne Gas & Flame Detection
The GD1 has been designed with features that provide an effective response to the detection of gas hazards in a wide range of industrial environments from offshore production facilities to wastewater treatment plants. At the heart of the detector is a tuneable laser diode that eliminates environmental effects from sun, rain and fog. The laser scans single absorption lines where there is no interference from other gases.The GD1 needs no recalibration and can replace multiple standard detectors to cover the same risk. The complete optomechanical design and construction is so stable that an ultra fast speed of response can be achieved while providing unparalleled service life and detector stability, thus saving on maintenance and service costs.Supplied with worldwide hazardous area approvals. Suitable for use in systems with SIL 2 requirement.
-
Product
Infrared Gas Detector
GD10 Series
-
Teledyne Gas & Flame Detection
The GD10 Series has been designed with features that provide an effective response to the detection of gas hazards in a wide range of industrial environments from boiler plant rooms to offshore petrochemical installations.These infrared gas detectors differ from all other models, because they utilize silicon based solid-state infrared sources. The complete optomechanical design and construction is so stable that an ultra fast speed of response can be achieved while providing unparalleled service life and detector stability, thus saving on maintenance and service costs.We offer the longest combined detector and IR source warranty on the market.
-
Product
Hazardous Area Gas Detector
Meridian
-
Teledyne Gas & Flame Detection
Whether you need an infrared or catalytic bead sensor to detect combustible gases or an electrochemical sensor for a toxic environment, the Meridian universal gas detector utilizes a single detector head to easily accept all sensor types. There is no requirement for distinct personality boards in the gas detector or different detector heads to make the instrument behave as a combustible or toxic gas detector. The Meridian gas detector accepts all sensor types in one detector. Simply attach the specific toxic or combustible sensor to the universal detector head and the Meridian gas detector will automatically determine the type of gas to be detected. Installation of the sensor is a simple plug-and-play action. At Teledyne Gas and Flame Detection, we are always looking to anticipate your future needs. We designed the Meridian gas detection platform to be future proof, allowing you to take advantage of new sensing technologies from Teledyne Gas and Flame Detection while maintaining ease of use and peace of mind.
-
Product
Fixed Gas Detectors
MicroSafe 500 & 600 Series
-
Teledyne Gas & Flame Detection
MicroSafe 500 and 600 Series gas detectors feature a non-intrusive operator interface. Calibration and programming instructions appear in simple intuitive and sequential script on a 16-character backlit display. The transmitter design incorporates extensive fault diagnostics with each condition conveniently identified on the transmitter display.The 500 Series comes standard with a linear 4-20 mA output, one-man remote calibration, self-adjusting zero and span, and LED indicators for fault and calibration status.The 600 Series includes the same features as the 500 with the addition of 3 alarm relays and an RS-485 serial communications port.Electrical Classification - Explosion proofClass I, Div 1, Groups B, C, D
-
Product
Toxic Gas Sensor
Model 100
-
Teledyne Gas & Flame Detection
Model DM-100 Series sensors feature intelligent electronics, non-intrusive operator interface and comprehensive fault diagnostics. The sensor is packaged in an electro-polished 316 stainless steel housing fitted with a ¾ inch NPT thread. The plug-in, field replaceable sensor cell features large surface area gold-plated pins that reduce the effects of corrosion in harsh industrial environments. Signal conditioning electronics are completely encapsulated in the sensor housing adding a high level of durability to the design. The packaging is XP-intrinsically safe. This innovative design marks a return to a simple, more affordable, and durable gas detection sensor without compromising quality.Model DM-100 sensors provide a 2-wire loop powered 4-20 mA current signal equivalent to the sensor range of detection. Upper enclosure options are aluminum and stainless steel. Additional accessories include wireless communications, a loop powered digital display. Each sensor is shipped with a splash guard with integral calibration port. Detcon’s toxic gas sensors have a long shelf life and are supported by an industry-leading warranty.
-
Product
Fixed Gas Analyzer
Model 1000
-
Teledyne Gas & Flame Detection
Natural gas pipeline monitor to detect H2S and CO2.Detcon Model 1000-CO2 and Model 1000-H2S Analyzers are designed to provide continuous, accurate, real-time measurement of gas concentrations in a wide variety of process gas streams. The instrument package is rated for Non-Hazardous areas.Consult commercial brochures for measurement ranges and more product features.
-
Product
Fixed Gas Detectors
OLCT 10 - OLC 10
-
Teledyne Gas & Flame Detection
The OLC 10 and OLCT 10 are designed to detect combustible or toxic gases for tertiary applications (boiler plants, battery charging rooms, car parks, hospitals). Two OLC 10's can be connected to one detection channel to monitor the same area, without an additional junction box or extra wiring. Similarly, up to five OLCT 10's can be connected to one channel for the detection of CO, NO or NO₂ in a car park application. Easy to install and operate, these detectors combined with the MX 16 control unit meet demanding user requirements.
-
Product
Fixed Digital Gas Detector
OLCT 10N
-
Teledyne Gas & Flame Detection
The OLCT 10N is a digital combustible gas detector designed for to detect combustible, toxic gases or oxygen. Intended for use in combination with the MX 16, MX 32 and MX 43 controller, the OLCT 10N provides a fast and accurate response.All transmitter information is received by the controller in less than 1 second.Non-intrusive operator interface requires only a simple magnetic wand and allows one man calibration without opening the enclosure.
-
Product
Industrial Gas Detector
OLCT 60
-
Teledyne Gas & Flame Detection
The OLCT 60AD version allows the sensor to be installed remotely up to 15 meters (standard), allowing detection in inaccessible locations, or in Zone 0 in the case of the intrinsically safe (IS) version. The detector units are made of 316L stainless steel, and are rugged and resistant to corrosion. Pre-calibrated sensors can be disconnected by turning the head of the unit. These “smart” sensors can be calibrated outside hazardous areas.The OLCT 60 is equipped with non-intrusive access to a safe menu. In hazardous areas, calibration can be done with an operating mode in accordance with safety rules.
-
Product
Fixed Gas Detector
OLCT 80
-
Teledyne Gas & Flame Detection
Oldham is pleased to propose its wireless system with the OLCT 80 field detector/transmitter. This model allows wireless connectivity in ATEX 1 zones.
-
Product
Open Path Combustible Gas Detector
SafEye (Quasar 900)
-
Teledyne Gas & Flame Detection
The Open Path Combustible system detects hydrocarbon gases by analyzing the absorption of radiation caused by gases in the atmosphere and comparing it to background atmospheric absorption. This is accomplished between a pair of units: a Flash Source and a Detector that can monitor a distance of up to 200 meters.Open Path Combustible Gas Detectors are robustly designed and can handle the toughest environments: 316L stainless steel housings that meet IP66/IP68 and NEMA 250 6P egress standards; circuit boards epoxy coated for protection; MIL-C-810C testing for humidity, salt, fog, vibration, mechanical shock and temperature extremes; and SIL-2 approval per IEC61508 is a final statement in reliability.
-
Product
Infrared Gas Detector
iTrans2
-
Teledyne Gas & Flame Detection
The iTrans2 infrared gas detector employs an intelligent electronics platform to provide one or two points of detection from a single head for maximum flexibility, superior performance and lower installation costs. With the optional HART Communication Protocol, the iTrans2 offers remote diagnostics, set-up or calibration by superimposing a high-frequency current across the industry standard 4-20mA analog line.
