Power Test Systems
-
Product
10 kV Subsea Power System
-
The Teledyne Oil and Gas 10 kV subsea power electrical connection system is a three-phase system rated to 250 A and 6/10 (12) kV. The electrical connection system is designed to provide power to motors used for subsea pumping systems.
-
Product
Defined CRPA Test System
BroadSim Wavefront Software
-
Protecting your GNSS systems from jamming and spoofing is more critical now than ever before. BroadSim Wavefront was designed to enable easier and more affordable CRPA receiver testing, leveraging proven software-defined architecture.
-
Product
SoC Test System
T2000
-
SoC devices require small-lot high-mix manufacturing methods in the present era of rapid generation change. Semiconductor makers struggle with requirements to replace their testers on a 2-3 year cycle. The T2000 addresses their needs by enabling rapid response to market needs with minimum capital investment.
-
Product
Bypass Diode Thermal Test System
-
King Design Industrial Co., Ltd.
* Power: the heating board control panel uses 220V single-phase power.* Power consumption: 1.0KVA, 1000W(Max)* Volt: 220VAC* Current: 4.5A* Heating board: one controller per board* Power rate: room temperature raise to 75°C± 5°C within one minute.* Heating board dimension: 500mm x 1,000mm* 6-sheet electrical heating boards test: used to test the 2,200mm x 2,600mm module. It can be customer-designed.* The length of board power cable and thermal sensor cable shall exceed 3,000mm.* To get uniform heating effect, the electrical board is sandwiched by 2mm aluminum sheets at both sides of board.
-
Product
High Voltage Isolation Test Systems
HT 9460 and 9464
-
Accurate and non-destructive production testing of ac Isolation Voltage and Partial Discharge. With over 450 systems installed worldwide the 946X series of test systems are the standard and system of choice used by the majority of semiconductor manufacturers that produce optically isolated devices.
-
Product
High Power Probe System Solutions
-
MPI Advanced Semiconductor Test
MPI high power probing solutions offer variety of probing systems which include manual, automated and fully-automated versions to provide solution for different budgets and specific requirements.
-
Product
LED Test Production System
Lumere-LC
-
Evolusys Technologies Sdn. Bhd.
Lumere LC is a LED test and measurement system for various parameters of LED light. It is economical, its geometry conforms with CIE-Publication 127, and the test program is easy to configure and adjust. Main application is in the production of LEDs.
-
Product
Power Supply System
PL508
-
The PL508 is a high sophisticated, high density, programmable 8-channel moderate floating low-voltage power supply system. Using the remote monitoring and control features it can be used to supply a large numbers of external load-channels with high power consumption also over long distances.
-
Product
Drive-Train/Power-Train Performance/Endurance Test System
-
This system is suitable for engine drive test or transaxle test of HEV/EV in combination with the real-time model calculation by the measurement/control panel and low inertial motor. Simulation test of an actual vehicle running condition can be executed by modeling a real tires or an engine. The tires and vehicles are modeled by MATLAB® / Simulink®, so they can be evaluated under various conditions by changing parameters or replacing models.
-
Product
Advanced Power System - Dynamic DC Power Supply, 9 V, 200 A, 2000 W
N7970A
DC Power Supply
The N7900 Series dynamic DC power supplies are designed for automated test equipment (ATE) applications where high-speed dynamic sourcing and measurement is needed.
-
Product
Low Frequency Test Systems
-
Ingenieurbüro Dr. Hillger Ultrasonic-Techniques
Our imaging low-frequency inspection systems are excellently suited to displaying internal defects with high resolution and high dynamics.
-
Product
Rotor Test Systems
-
Automation Technology's RTS-3800 Rotor Test Systems offer an unparalleled ability to test the quality of die cast or PM rotors. The RTS-3800 is packed with standard features and like all of ATI's 3800 Series Test Systems; the RTS-3800 is backed by ATI's industry leading two-year limited warranty.
-
Product
Test Fixture
N1295A
Test Fixture
The Keysight N1295A Device/Component Test Fixture provides a low-cost solution to quickly and easily test packaged devices and components. For more advanced packaged testing needs, the Keysight 16442B Test Fixture provides more capabilities.
-
Product
Regenerative Power System, 950 V, 20 A, 10 kW, 200/208 VAC
RP7953A
DC Power Supply
The RP7953A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test. The regenerative capability enables the energy normally consumed to be returned to the grid cleanly, saving costs associated with energy consumption and cooling.
-
Product
Geophone Testing – Hydrophone Testing – Vibrator TestingVersatile Quality Control System - Three Test Units In One!
Bird Dog 3 - 3 Channels
-
*32-bit, high speed, ADC chip for lower noise and increased accuracy*Three different operation with a single unit*8 Gigabytes of Data Storage, Expandable to 16*GPS based time and location saved for every record*Stable and rugged unit for use in all conditions*Three-Component Test Mode, checks 3 elements at onceto save time and effort*All test data saved in non-volatile memory for later download and retrieval*Connects to PC via Ethernet or optional Wi-Fi, provides control, data download and real time display and analysis of data and results
-
Product
Custom Configured MPS, 600W
N6711C
Power Supply
The Keysight N6711C is a 600 W build-to-order system that is shipped as a fully tested and assembled multiple-output power supply. Each N6711C consists of 1 N6701C mainframe and from 1 to 4 DC power modules. Modules are ordered as options to the N6711C.
-
Product
Test Automation System for Brake Testing
STARS Brake
-
STARS Brake is an integrated automation, data acquisition and control system platform that provides a comprehensive application functionality in a single, powerful environment. STARS Brake is designed to address the needs of a wide range of brake testing applications from component development to final component and system validation. It offers users a level of flexibility and openness that enables thorough investigations of brake systems.
-
Product
Backplane Test System
402LV
-
Very High Pin Count Level IV Backplane Test System. To ensure that Testronics maintains its leadership position as the premier supplier of backplane testers, we will be introducing our solution to testing high pin count / very large backplanes, the Model 402.
-
Product
High Voltage DC Cable Test Systems
-
We can offer from ±18kVdc to ±30kVdc units which all have automatic earthing for discharging capacitive loads. They are designed to perform tests on installed cables and jointing systems.
-
Product
SIP-90-5 Test System Interface Probe
SIP-90-5
ICT/FCT Probe
Overall Length (mil): 1,000Overall Length (mm): 25.40Rec. Mounting Hole Size (mil): 55Rec. Mounting Hole Size (mm): 1.40Recommended Drill Size: #54 or 1.40 mm
-
Product
ARTES Automatic Relay Test Systems
-
The purpose of power system protection is to use accurate and reliable protection devices to detect faults promptly and without fail and to minimize impairments to the power supply by selectively switching off faulted sections of the system.The use of suitable protection devices can significantly improve the safety and reliability of complex electrical power systems and installations. Regular testing is the only way to ensure that these protection devices function correctly throughout their operational life.More than 20 years of experience in developing and manufacturing automatic relay test systems have gone into creating the third generation of ARTES test instruments. Back in 1996, KoCoS was the first company to present Windowsbased testing software for controlling and operating test equipment and the company continues to play a pioneering role in the design of clearly structured and ergonomic user interfaces today.
-
Product
Programmable Switching DC Power Supply 1 Output, 0-160V, 0-14A, 720W
T3PS160141P
DC Power Supply
Programmable Switching DC Power Supply 1 Output, 0-160V, 0-14A, 720W.
-
Product
Low Voltage Test System
CKT T1
-
The CKT T1 is a compact size solid-state test system featuring 128 test points.
-
Product
Battery Powered Telemetry Systems
-
Advanced Telemetrics International
ATi’s Battery Powered Telemetry Systems are ideal for transmitting coupled data signals from sensors, which are mounted on rotating shafts or machinery to a stationary receiver.
-
Product
Precision Multiferroic and Ferroelectric Test System
-
The Precision Multiferroic tester is Radiant's most advanced test system. The Multiferroic has fast built-in frequency at 30kHz measurements using the 200V internal amplifier and 50kHz measurements using the 100V internal amplifier. This system comes in a built-in option of +/-100V, 200V, and 500V and can be expanded to 10kV. This unit also comes with a 18 bit ADC and requires no configuration changes.
-
Product
Power, Patchcord, Receiver, 36", Micro Power, 12 AWG White, Single Ended (22 Amps)
7-252912000-036
Power Patchcord
Power, Patchcord, Receiver, 36", Micro Power, 12 AWG White, Single Ended (22 Amps).
-
Product
Vibration Test Chamber Elevator Mechanism System
-
Guangdong Test EQ Equipment co., Ltd.
- Structural Design: Monolithic construction with seamless TIG welding for durability and aesthetics. Lever-driven door lock mechanism.- Smart Control System: Features a Chinese/English-language color LCD touchscreen HMI + high-performance PLC, powered by TESTEQ's proprietary software for automated, intelligent, and user-friendly operation.- Energy Efficiency: Incorporates TESTEQ's patented "Static Balance" technology, reducing energy consumption by over 30% during low-temperature stabilization.- Vibration Integration: Elevator Mechanism: Wireless remote-controlled for alignment with horizontal/vertical vibration platforms.- Advanced Sealing: Custom flexible connectors ensure airtight integration between temperature/humidity chambers and vibration platforms.
-
Product
Power, Patchcord, ITA, Micro Power, 36", 14 AWG White Teflon, Single Ended, (22 Amps)
7-251914000-036
Power Patchcord
Power, Patchcord, ITA, Micro Power (22 Amps), 36", 14 AWG White Teflon, Single Ended, (30 Amps)
-
Product
Ethernet and Fibre Channel Test Platform
SierraNet M1288
Test Platform
The SierraNet M1288 Ethernet and Fibre Channel test platform provides best in class analysis, jamming and generation for traffic capture and manipulation for testing application and link characteristics. SierraNet M1288 is the latest in the line of industry leading test and measurement tools from Teledyne LeCroy, designed for today’s high-speed storage and communications fabrics. SierraNet M1288 supports examination and modification of Ethernet and Fibre Channel links utilizing both Pulse Amplitude Modulation 4 (PAM4) and legacy Non-Return to Zero (NRZ) technologies.
-
Product
Test Automation System for Engine Testing
STARS Engine
-
With a wide range of user-friendly features, STARS Engine can run the most complex of tests with a simple press of a button making your test operation effective and efficient and above all, reliable. STARS provides all the features you need to run a wide range of Engine Test Programmes from simple manual testing to dynamic automatic tests, all from a single, simple to use user interface. STARS is designed to be run in either stand-alone operation for a single test stand or as a cluster of systems to allow a test field to be run more efficiently. In both cases the user works in the same way and uses the same interface.
