- Taylor Dynamometer, Inc.
product
Water Brake Chassis Dynamometers
Chassis water brake dynos (also known as hydraulic dynamometers) can be operated continuously to resolve overheating, fuel mileage and drivetrain issues. Taylor’s eight models accommodating 50 to 1,100 hp at 40 mph enable testing of single-axle diesel pickup trucks, RVs and buses up through the largest tandem-axle on-highway trucks and buses. Tap into our deep product and applications knowledge to help you choose and make the most of the right water brake system for current and future needs.
-
product
Piezoelectric Vibration Pickup
PU-8ALSF
*Side outlet type with assembled *cap nut*Built-in amplifier*Use up to 150 ℃ enabled
-
product
Gated Integrator | Boxcar Averager
GIA100
Artifex Engineering GmbH & Co. KG
The GIA100 gated integrator employs dual monolithic switched integrators. When paired with a photodiode, the boxcar amplifier measures the energy of single optical pulses. The GIA100 design results in very low leakage error, charge injection error and pickup. The precision input stage may be configured for current or voltage inputs.
-
product
Measuring Wheel
B20-S
Simple and light Measuring Wheel B20-s can measure up to 10,000m at 10cm graduation.The counter is indicated in 5 digits and has reset button. When we use Leak Noise Correlator LC-2500, we need to input the between pick-up sensors.
-
product
Seismic Sensors & Transducers
Displacement Pickups are vibration transducers that incorporate a spring-mass system with eddy-current damping using a frictionless pivot. This pivot is a spring flexure that serves as the ‘spring’ and a moment arm attached to the pivot serves as the ‘mass’, which allows resolutions down to the micro inch range. At frequencies above 50Hz, the mass remains fixed in space and becomes an inertial reference. A transducer within the pickup senses the motion of the mounting base relative to the inerti...show more -
product
Optical Pickup
1037-DTS
TESCO introduces a new optical pickup (Catalog No. 1037-DTS) for one way meter communication through the calibration LED found on most solid state meters. The pickup senses infrared pulses from ANSI compliant meters for complete, automatic testing.
-
product
COMPUTERIZED AUTOMATIC RELAY TEST SYSTEM
CVRT-S16
CVRT-S8 & S16 are ideal for automatic testing of ELECTRO MECHANICAL AND READ RELAYS (only DC relays) both for static and dynamic characteristics. This system scans at one stroke, all the parameters of the relay as per definition of test procedure. The test sequence can be pre-programmed and stored in the disk. You can select the tests as per your requirement. Can include or exclude the test and you can have several options to match your test definitions. Semi skilled person can be enga...show more -
product
Piezoelectric Vibration Pickup
PU-8ANSF
*Side outlet*Easy to remove due to cap nut type*Use up to 150 ℃ enabled
-
product
Speed Sensors
Speed sensors for both indoor and outdoor environments with options featuring kits for motors, geartooth pickup, tachometers, and stroboscopes.
-
product
Motorcycle and ATV Dynamometers
Wide medium inertia roll assembly with our machined-in "traction grooves," quick-adjust wheelbase front mount, dual roll-on ramps, tie downs, casters, roller guards, eddy-current absorber (with a step-up drive), full-bridge torque arm transducer, electronic auto-load control, DYNOmite data-acquisition computer, DYNO-MAX software, inductive RPM pickup, AC power supply, and data wiring harness.
-
product
Secondary Injection Relay Test Set
TD 1000 PLUS
TD1000+ is a protective relay test set especially designed to give the commissioning engineers a multitasking and highly reliable testing equipment. In comparison with T 1000 PLUS model, TD 1000 PLUS has two current outputs to test the differential relay characteristic curve, besides the pick-up current.
-
product
2WD Dynamometers
MD-500-SE XL
The 500 series dynamometer has a larger big brother – the MD-500-SE XL! The 500-SE is an excellent 2WD performance dynamometer and the XL model expands on these traits by adding in a much wider 98-inch outer track and a HUGE mechanical flywheel to increase the mechanical inertia of the dyno to about 2,000-lbs. This additional inertia helps reduce the duty cycle burden on the eddy current PAU and even allows for pulls to be done in a pinch in inertia-only mode. The XL han...show more -
product
Digital Engine Analyzer/Multimeter
385A
The #385A has many of the necessary features required for today’s automotive diagnostics. Use frequency readings to test crankshaft and camshaft sensors, for example. The #385A comes equipped with an RPM pick-up, probe test leads, alligator clip test leads, protective holster, instructions and installed 9V battery. Inductive RPM pick-up features a five position, adjustable sensitivity switch.
-
product
EZ TACHOMETER PLUS
ETP328
*Small engine tachometer reads engine speeds up to 20,000 RPM*Works wirelessly or with inductive pick-up clip*Accuracy: +/- 10 RPM
-
product
Cable Avoidance Tool
CXL3
The CXL3 is a robust and affordable analogue industry standard ‘pick-up-and-go’ Cable Avoidance Tool used to detect pipes and cables prior to excavations. Designed for use with an SGA3 Signal Generator.
-
product
Lock-In Voltage Preamplifier
SR550
Stanford Research Systems, Inc.
The SR550 Voltage Preamplifier is designed to work with any SRS lock-in amplifier. Preamplifiers provide gain close to the experimental detector, before the signal-to-noise ratio is permanently degraded by cable capacitance and pickup
-
product
Lock-In Voltage Preamplifier
SR552
Stanford Research Systems, Inc.
The SR552 Voltage Preamplifier is designed to work with SRS lock-in amplifiers, providing gain where it is needed most?right at the experiment. The preamplifier minimizes noise and pickup in the connecting lines and can reduce measurement time in noise-limited experiments.
-
product
Powder Brake Dynamometers
PB Series
The Powder Brake Dynamometer (PB Series) contains, as its name suggests, a magnetic powder. The electrical current passing through the coil generates a magnetic field, which changes the property of the powder, thus producing a smooth braking torque through friction. They are ideal for applications operating in the low to middle speed range or when operating in the middle to high torque range. Like Hysteresis Brakes, Powder Brakes provide full torque at zero speed. Like the Eddy-Current Brake Dyn...show more -
product
Lightweight Vehicle Surveillance System
LVSS
The skid-based LVSS converts a standard commercial pickup into a rapidly deployable command and control center. Within minutes, a single operator can set up the LVSS and report for full perimeter duty from the comfort of the cab. When it’s time to relocate, the mast and its mounted FLIR cameras, radar, and sensors, stow out of sight for covert transportation.
-
product
KYZ Indicator and Tester
1031-C3, 1031-C6
More than just an indicator, TESCO’s KYZ Indicator and Tester Cat. 1031-C3 (3-wire) and 1031-C6 (6-wire) can also be used to perform accuracy testing of KYZ pulses on all TESCO Next Generation Test Equipment. TESCO’s KYZ Indicator and Testers can be used as a pulse input using the same pickup connection on the front panel of all TESCO Next Generation Test Equipment.
-
product
Electrodynamic Velocity Pickup
The principle of Reciprocal Pendulum type Pickup is to induce voltage by reciprocal motion of the seismic mass with a coil in the magnetic field being suspended by a diaphragm or coil spring.. Because of its High Sensitivity and Advanced Linearity, it is suitable for detection of malfunction or deterioration of rotational machineries. Due to its structure, mounting should be done carefully for its direction or angle.
-
product
Piezoelectric Vibration Pickup
PU-626E
*Connector type with upper outlet*Waterproof (IPX6), suitable for a wide range
-
product
Piezoelectric Vibration Pickup
PU-6ALSF
*Side outlet type*Easy to remove due to cap nut type*Use up to 80 ℃ enabled
-
product
Heavy Duty Dynamometers
MD-250-HD
The MD-250-HD series dyno (SE/DE) was designed to be a performance dynamometer first with the added benefit of being able to test 2-wheel-drive heavy-duty vehicles such as truck, buses and commercial vehicles in addition to the standard car or light duty pick-up. The 250-HD is certified in the states of Colorado, Nevada and Utah for use in loaded-mode diesel smog testing programs because of its accuracy and reliability. No other dyno in its class offers more value or better in-house motor vehicl...show more -
product
Leak Locator
XL-2
Lightweight & Strong11 Position filter to pinpoint leak and remove background sounds2 Sensitivity controlsSuper Sensitive magnetic transducerHigh gain, 4-stage amplifierVisual and Audible indicationsCoarse and Fine SensitivityExtremely sensitive pickup with removable 7" (177.8mm) probeBattery operated and with battery condition indicator
-
product
Power Monitor, AC-Powered, Field Adjustable
YMA/YQA
NAI's YMA and YQA Power Monitors are used to monitor voltage, frequency, and phase characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within predetermined limits.High and low voltage and frequency limits, and "pick-up" and "drop-out" time delay are field-adjustable using potentiometers. These power monitors are ideally suited for rugged defense and industrial applications.
-
product
Optical Power Meters
A handheld optical power meter, which is most suitable for production of LDs, optical pickups and drives for optical disks.It was developed to meet functions and performance suitable for CD/DVD production.
-
product
Short Circuit Finders
The ShortSniffer locates short circuits in electronics circuits, projects, and printed circuit boards. * locates PCB shorts under solder mask, under components, and even on inner PCB layers * non-contact (inductive) pickup wand * pinpoint short to within 2mm radius (SS2) * rapid location with audio feedback * "follow the sound to the short" * no need for relative or reference measurements * battery operated * diode clamped current drive, won't harm your circuitry
-
-
product
Flow Meter Sensor
RF Pickups
SPECTEC Innovative Sensor Solutions
SPECTEC RF pickups are excellent for applications that require near zero speed and zero magnetic drag sensing characteristics, such as flow meter sensor applications. SPECTEC RF (modulated carrier) sensors have a long history of use in turbine flow meters and turbine engines in the aerospace, petroleum, chemical, pharmaceutical and food industries.
