Excitation Current
-
Product
Modal Exciters & Amplifiers
-
Experimental modal analysis, or modal testing, is a process for physically obtaining a math model of a structure’s dynamic properties. Modal tests identify a structure’s modal properties: natural frequencies, mode shapes, mass, stiffness and damping. Modal test results help troubleshoot resonant excitation from operating forces, validate and verify finite element models, predict the benefits of structural modifications, support design verification, and understand structural responses due to complex loading conditions.
-
Product
Current Probes | Current Sensors
-
Sensitivity of Conventional Probes Deliver Precise Measurement of Low Current Waveforms from 1 mA. High-precision Current Sensors, DC to 4 MHz, DC to 20 kHz, up to 50 kHz and load current sensors,
-
Product
Stand-Alone Current Sensors
-
The Aanderaa Current Sensors are based on the backscatter acoustic Doppler principle.
-
Product
XCITE 1100-5 Inertial Mass Excitation System
-
The 1100-5 Inertial Mass Modal Excitation system allows the testing of structures where backup fixturing is not available or possible. Accelerating an internal mass with the closed loop hydraulic excitation system generates the inertial forces. The compression control of the Xcite Master Controller maintains a constant force over a frequency sweep by continuously altering the drive signal to maintain the required dynamic force level.
-
Product
Primary Current Injection
PCI-600
-
The VIC Model PCI-600 is a programmable, high-current source that is designed specifically for utility-substation applications. This alternating current(ac) test device is used primarily for injection testing of protective relays. This same device can also be used for testing thermal, magnetic and solid-state motor-protection relays and molded-case circuit breakers.
-
Product
Voltage And Current Amplifier
KINGSINE KA30 / KA60
-
KINGSINE Electric Automation Co., Ltd.
KINGSINE's KA30 / KA60 voltage and current amplifier is high accuracy, high power, Panel-mounted type real time simulation power amplifier with four-phase voltage and three-phase current.
-
Product
Current Meter
Model 106
-
The Model 106 is the ideal instrument for coastal and estuarine applications and other light-duty survey work.
-
Product
Current Transformers
Sensors
-
The Current Transformer (CT) is the sensor which measures the amount of current draw from the wire it is installed on.
-
Product
Current Transformers
-
Contrel Elettronica s.r.l. Company
We can supply current transformers (measure transformers, protection transformers and double ratio transformers, with analog output) with the following accuracy classes: 0.1, 0.2s, 0.5s; 1; 3. A wide range of combinations is available in our standard range with specific versions available upon request (other ratios, specific frequency, class or load). They are equipped with sealable terminal covers as standard.
-
Product
High Current SMU
-
Source and Measurement Units (SMUs) are devices that generate voltages or currents and can measure them simultaneously using the integrated measurement units (VMU, CMU).High current SMUs operate as a regulated power source and are able to generate very high output currents as pulses.
-
Product
Leakage Current Testers
-
For general-use electrical devices Built-in non-medical use networks For rated currents of up to 20A For automatic testing on production lines, etc.
-
Product
High Current Sensor
HCS-BTA
-
Vernier Software & Technology, LLC
Use the High Current Sensor in experiments that involve currents larger than 1 A, such as solar panels, hand generators, and other alternative energy projects.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-400B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Leakage Current Tester
TOS3200
-
The Leakage Current Tester TOS3200 is designed to perform leakage current (touch current and protective conductor current) tests on general electrical equipment but not medical electrical equipment.It enables you to conduct tests that conform to the requirements of the applicable IEC, UL, JIS, and other standards, as well as the Electrical Appliance and Material Safety Law. The memory in the main unit stores the 51 types of test conditions laid down in the IEC/JIS standards for information technology equipment, household electrical appliances, audio, video electronic apparatus, luminaires, motor-operated electric tools, and electrical equipment for measurement and control and in the Electrical Appliance and Material Safety Law, thereby enabling you to conduct standard tests with simple panel operation.
-
Product
Eddy Current Dynamometer
EC Series
-
Specifically designed for small displacement diesel engines, the Eddy Current (EC-Series) engine dynamometer features in-line eddy current absorption units in a robust, compact frame. The air-cooled eddy current absorbers eliminate the need for an expensive water recirculation system and most engines being tested can be cooled with a standard closed-circuit radiator system. This compact air-cooled design results in a minimal environmental impact and the ability to be easily relocated with no need for a permanent installation. When combined with PowerNet LT, our fully automated dynamometer control system, all of your testing needs can be performed at the touch of a button.
-
Product
Profiling Current Meter and Wave
SeaGuardII DCP Wave
-
The SeaGuardII DCP Wave is a 600kHz Doppler Current Profiler able to measure directional wave parameters and currents from a bottom mounted installation.The Acoustic Wave software 5759 used by the DCPS implements unique features to improve the wave measurement accuracy by optimizing the signal to noise ratio.Maximum deployment depth is 40m in normal scatter conditions. The Profiling Current Meter and Waveis available as a self-recording instrument. It can be easily integrated into a real-time system offering reliable two-way communication.
-
Product
Combinated Current Clamps
-
PeakTech Prüf- und Messtechnik GmbH
Measure small direct and alternating currents up to 2 A with 1 mA resolution. The device measures the current indirectly via the surrounding magnetic field, so it is measured without contact when the clamp jaws enclose the current-carrying conductor (single wire).
-
Product
Rogowski AC Current Probe
RCP500
-
Shenzhen Micsig Instruments Co., Ltd.
Adopts the Rogowski coil current measurement system: within the range, the output signal of the system and the current signal to be measured are always linear, so the accuracy will not change with the current; The RCP500 measures AC current up to 500A pk, minimum to 200mA pk, with bandwidth ranging from 15Hz to 300KHz, 1% accuracy, and has less than 2mV noise. Directly powered by Micsig UPI interface, realise auto scaling setup,
-
Product
Pulsed Eddy Current (PEC)
Lyft®
-
Lyft is a high-performance solution reinventing pulsed eddy current (PEC). The patent-pending Eddyfi® solution features:
-
Product
AC Current Clamp Adapter
LAD-1100
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
●Selectable measuring range 30mA~30A with CT ratio 10:1 and 30A~3000A with CT ratio 100:1.●φ110mm CT window, possible to measure from leakage to big current up to 3000A.
-
Product
Current Transformers Test Set
-
Supreme Instrument Laboratories
The basic unit is sensitive magnetic comparator and also it incorporates electronic null detector to facilitate the balance. The reference Current 5A. or IA. obtained from Standard Current Transformer and in comparison to that the vector length and phase displacement is measured. The ratio error in percentage and phase displacement in minutes are directly compared and indicated on dials.
-
Product
Current Probes
-
Current probes allow you to measure DC or AC current. Yokogawa's selection of current probes allow measurements ranges up to 500 ARMS and bandwidths up to 100MHz.
-
Product
Automatic Current Tester
77069
-
For the rapid safe and accurate testing of DC current on 12v vehicles. The tool plugs straight into the vehicles fuse board and displays the current on the large LCD display. Specification range 0-48volt max 20 amps, 12v battery included.
-
Product
DC Leakage Current Monitor
MDLA-100
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
This DC Leakage Current Monitor constantly observes leakage current of DC circuit like as PV generation system, etc. and lights up the warning lamp with signal output, when the leakage current exceeds the setting value.
-
Product
DC/AC High Current Probe
698
-
Unit is designed for use with digital multimeters,lab scopes or graphing meters. With 1000 Amp capabiltiy, this instrument can be used to test starting and charging systems. It can even be used to test relative compression when used with your lab scope or graphing meter.
-
Product
L.V. Current Transformers
-
ENTES LV Current Transformers are measuring transformers which transform the primary current by a specified ratio to its secondary side with a phase difference of 0 degrees. They provide isolation of the relays and measuring devices from the HV side of the network.
-
Product
Resistance Tester With Leakage Current (Loop Current)
GT00WD00ZY
-
*screen display*Double protection insulation*Non-contact measured resistance, safe, fast
-
Product
Industrial Current Sensors
RCT
-
Power Electronic Measurments Ltd
The RCT range of AC current transducers are designed for permanent or semi-permanent installation and are available with industry standard outputs.
-
Product
DC Current Shunts
-
DC current shunts / standards are true 4-terminal devices that precisely measure DC currents from 10 A to 10,000 A. They use special alloys in the resistive elements which are supported on an insulating base for mechanical stability. The 9230A includes special features to reduce the effects of power dissipation and associated self heating errors. These shunts are designed to operate in air at full rated current. These are the best performing, and most widely used, DC metrology shunts in the world.
-
Product
Current Transformer
-
Nippen Electrical Instruments Co.
DIGITAL METERS NIPPEN electronic energy meters are panel mounting type innovative energy monitoring devices ,having state of the art electronic microcontroller circuitry for reliability and accuracy. They can be used for 1Ø / 3Ø balanced and unbalanced loads.
