Single Wire Protocol
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 125 MS/s on 4 Channels (Single Ended) or 4 Channels (Differential), up to 80 MS/s on 8 Channels (Single Ended)
M2P.5968-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
MEMS Fiber Optical Switch at Single Mode 1315nm Type-A with LC/PC Connector
SUN-MS-1x8
-
Guilin GLsun Science and Tech Group Co., LTD
Fiber Configurations1x8 MEMSFiber TypeSM, 9/125 umTest Wavelength1310/1550 nmOperating Voltage2.5VSwitch TypeNon-latchingFiber Length0.5m±5cmConnectorTTL/UARTTube Type900 umOperating Temperature-5°C~ +70°CStorge Temperature-40°C ~ +85°C
-
Product
Single 24x4 1-Pole High-Density PXI Matrix Module
40-520-402
Matrix Switch Module
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI Single Microwave SPDT Relay 26.5GHz 50 SMA
40-780A-531
Relay
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options)
-
Product
PXI/PXIe RF Multiplexer, Single 4-Channel, 3GHz, 50Ω, SMB
40-872A-001
Multiplexer Module
The 40-872A-001 (PXI) and 42-872A-001 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 1 bank in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths of the 40/42-872A has been minimized by careful attention to the mechanical and electrical design.
-
Product
36W to 82.5W - Single Output
iSA Series
-
*1/16th Brick Footprint*36-75 Vdc Input*1.2V 30A, 12V 6.5A Nominal Outputs*1500 Vdc Isolation*Constant Switching Frequency
-
Product
LXI Microwave Matrix, 20GHz, Single 4x4 With Loop-Thru
60-751-144-A
Matrix Switch Module
The 60-751-144-A is a single 4x4 20GHz microwave matrix with loop-thru. It is part of the 60-750/751 range of LXI Microwave Switches controlled through an LXI compliant Ethernet connection. It is available in a variety of configurations and frequencies up to 20GHz (60-751). The matrix is characterized for 50 ohm applications, for 75 ohm versions please consult your local sales representative.
-
Product
3 Wire (Digital) Earth Resistance Tester
2720 ER
-
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Data hold function.● Battery test indication.● Calibration performed with supplied test leads.
-
Product
Single Channel USB Programmable High-Pass Filter
USBPHP-S1
-
The USBPHP-S1 stand alone USB controllable module provides a single channel of high pass filtering and high-quality instrumentation amplifier for front-end signal conditioning compatible with all popular A/D converter devices. The USBPHP-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPHP-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPHP-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.
-
Product
4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers
-
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.
-
Product
LXI Microwave Matrix, 10GHz, Single 8x4
60-750-184
Matrix Switch Module
The 60-750-184 is a single 8x4 10GHz microwave matrix. It is part of the 60-750/751 range of LXI Microwave Switches controlled through an LXI compliant Ethernet connection. It is available in a variety of configurations and frequencies up to 18GHz (60-751). The matrix is characterized for 50 ohm applications, for 75 ohm versions please consult your local sales representative.
-
Product
Receiver, RTCASS, 19 Position, Single Tier, Lightweight
310115119
Receiver
Receiver, RTCASS, 19 Position, Single Tier, Lightweight.
-
Product
PXI Single Microwave SPDT Relay 18GHz 50 SMA - External Termination
40-781-121
Relay
This single microwave SPDT relay module is part of the 40-781 range that consists of one or two changeover switches capable of switching frequencies to 18GHz in 50 Ohm. Versions are available with either internal or external terminations and connections are made via front panel mounted high quality SMA RF coaxial connectors.
-
Product
Signal Module, ITA, QuadraPaddle, 480 Position, Fully Loaded For Wire Wrap With Anti-Rotation (610 138 122)
510151127
ITA Module
QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based Mass InterConnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .100” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
Product
Switch Modules - 16 Single Pole, Form A, Discrete Relays Which are Wired & Controlled Individually
JX16/KA
Switch Module
This module has 16 single pole, Form A, discrete relays which are wired and controlled individually. The relays can be externally wired to make any configuration needed. Use as individual ON/OFF relays or use them to drive external relays, solinoids, or any external device. It is available with Type S or M reed relays.
-
Product
Wire Harness Tester
NX Solo
-
The Dynalab NX Solo Tester is an economical, feature-rich, stand-alone wire harness tester offering up to 256 test points. The powerful NX Editor software application is used to create unique program files to successfully validate all electrical and electro-mechanical wire harness parameters. This tester is compatible with all Dynalab NX accessories such as printers, scanners, control ports, and much more. The NX Solo Tester supports network communications with the NX Server for efficient file transfers and advanced data collection.
-
Product
14W to 60W - Single Output
ZPSA Series
-
*Wide Range AC Input*Low Profile, Industry Standard Footprint*Global Safety Agency Compliance*EN61000-4 Immunity
-
Product
PXI/PXIe High Voltage Multiplexer, Single 23-Channel, 2-Pole
40-321-127-HI
Multiplexer Module
The 40-321-127-HI (PXI) and 42-321-127-HI (PXIe) are single 23-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
PXI/PXIe RF Multiplexer, Single 16-Channel, Terminated, 8GHz, 50Ω, SMA
40-883B-002
Multiplexer Module
The 40-883B-002 (PXI) and 42-883B-002 (PXIe) are single 16 to 1 50Ω RF multiplexers with 8GHz bandwidth and automatic termination of unused signal channels. They are available in 8 to 1 and 16 to 1 configurations in two and three slots respectively.
-
Product
8 CANBus Channels, CAN 2.0 A/B Protocol
CB1
-
The serial bus system with real-time capabilities is the subject of the ISO 11898 International Standard and covers the lowest two layers of the ISO/OSI Reference Model. Our CANBus modules provide independent, isolated channels of CAN serial data bus links, conforming to the ISO 11898 International Standard. All CAN nodes are able to transmit data and several CAN nodes can request the bus simultaneously.
-
Product
Gauge Type T Thermocouple Wire
W-TW-44P
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
PXIe Microwave Relay, Single SPDT, 26.5 GHz, 50 Ω, SMA, Failsafe
42-780B-531
Microwave Relay Module
The 40-780B-531 (PXI) and 42-780B-531 (PXIe) are single failsafe SPDT 26.5 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
Single Event Effects Test System
SEE-RAD
-
The SEE-RAD test system brings together the proven features of our ETS780 tester (such as true APG memory test and powerful FA tools) with the newest technology of the Griffin III. With all new high-accuracy DC Parametrics, superior precision pin drivers, and capture memory of 64M, the Griffin SEE-RAD combines the newest innovations in the test industry with our years of experience in Radiation Test.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP6T, 40GHz, 50Ω, SMA-2.9
40-785C-541
Multiplexer Module
The 40-785C-541 (PXI) and 42-785C-541 (PXIe) are single SP6T 40GHz unterminated microwave multiplexers. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
Protocol Control Control
PC2
-
The PC2 software from SCSI Toolbox, LLC brings a new level of parallel SCSI protocol control to your test environment. Designed in cooperation with LSI Logic to work with their Fusion-MPT Message Passing Interface technology, PC2 allows all negotiated parameters to be displayed or set for all devices connected to any SCSI Host Bus Adapter based on the LSI53C1030 chip set. PC2 also provides the means to generate hardware SCSI bus resets.
-
Product
80W - Single Output
iBH Series
-
*DOSA Compatible Footprint*3.5-14 Vdc Input*0.7-5.5 Vdc Output*Non-Isolated*Excellent Transient Response*No external loop tuning components needed
-
Product
Intel® Celeron J1900 & Atom™ E3825/ E3845, 3.5" SBC
MIO-5850
Single Board Computer
Intel® Celeron J1900 & Atom™ E3825/E3845, DDR3L-1333MHz 2/4GB on boardDirectX11, OpenGL3.2, OpenCL1.2, Dual display: HDMI, VGA, LVDSCPU bottom up design for system integration and rugged design for variable automation factory environments3 Intel i210 GbE, rich I/O: 4COM, SATA, USB3.0, SMBus/I2C, 16 bit GPIO, full-size Mini PCIe/M.2 E Key, half size mSATA, 12-24V Power input, SIM Card holder, CANBUS with IsolationSupports iManager, SUSI APIs, WISE-DeviceOn and Edge AI Suite
-
Product
PXI/PXIe MIL-STD-1553 Multiplexer, Single 4-Channel, 2-Pole
40-739-005
Multiplexer Module
The 40-739-005 (PXI) and 42-739-005 (PXIe) are single 4-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
Product
Single Head Component Testers
34XX
-
Performs DC, AC, and pulsed tests. Excels at evaluating difficult to measure parameters on zeners, current limiters, varactor tuning diodes, darlingtons and matched dual transistors. 24 bin opto-isolated handler/prober interface. Parallel first-in first out computer to tester interface for maximum throughput. Parallel testing with a 3402E or 3403E allows shared test execution for extremely high throughput applications when interfaced to high speed handlers with multiple test sites.
-
Product
PXI/PXIe Microwave Relay, Single SPDT, 67 GHz, 50 Ω, SMA-1.85, Failsafe
42-780B-571
Relay
The 40-780B-571 (PXI) and 42-780B-571 (PXIe) are single failsafe SPDT 67 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
