Programmable Logic Controller
Programmable Logic Controller
-
product
Controller
YFC
The YFC-35D operates with only the YF-Series brushless electric screwdrivers. It is a single tool controller that offers programmable speed, angle, auto reverse and soft start options. The controller provides programmable fastening options for sequence based assembly automation applications.
-
product
PXI Precision Resistor Module 4-Channel, 2 to 102k
40-297-134
This 4-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
FPGA-Based Ultra-Fast Flash Programmer
XJFlash
XJFlash is an FPGA-based advanced and innovative method that uses JTAG for high-speed in-system programming (ISP) of flash memories – all serial and parallel flash devices are supported. The most common use of XJFlash is programming the SPI/QSPI NOR flash used to configure an FPGA.
-
product
Pressure Control Setup Using Pid Controller
ULP-26
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Pressure Control Setup comprises of Pressure tank fitted with pressure transmitter to measure the pressure. The pressure is controlled by a pneumatic control valve operated by a I to P converter. The whole system is mounted on a Table top Model with all necessary Piping. The electronic panel comprises of ADC/DAC card with RS-232 interfaces.
-
product
Altitude Encoder Calibration Programmer
ECP-100
The ECP-100 allows the avionics technician to assign serial port protocols, 100' or 10' resolution and/or allow programming of the calibration curve on Trans-Cal Altitude Encoders using the RS232 port.
-
product
Controls Systems for Engine Control and Combustion Analysis
NI Powertrain
NI Powertrain Controls systems incorporate the LabVIEW reconfigurable I/O (RIO) architecture to create some of the world’s most flexible and capable combustion analysis and engine control systems. The engine control systems can drive both solenoid and piezoelectric direct injectors, control timing events with 25 ns of precision, and implement novel engine control strategies such as next- and same-cycle control. The combustion analysis systems are available in both portable and higher performance stationary form factors.
-
product
VXI Mainframes & Controllers
The Keysight VXI mainframes provide rugged enclosures with innovative air distribution systems for extremely quiet and efficient cooling. With power supply capacities up to 1000 watts, you can easily configure the system that truly meets your needs.
-
product
PCI High Density Pecision Resistor Card, 6-Channel, 4Ω To 1.51MΩ
50-298-050
The 50-298-050 is a high density programmable resistor card with 6 channels which can be set between 4Ω and 1.51MΩ with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Scienlab Emulator Control Software
SL1092A
The Emulator Control software can control Scienlab systems from Keysight such as the Machine Emulator and the Dynamic DC Emulator. The software also can manage both emulators combined in a test bench manually.
-
product
Multi-Loop Controllers
Omega Multi-Loop Controllers combine higly accurate and configurable multi-channel inputs with a comprehensive set of control modes and output features plus easy configration and setup.
-
product
8-Channel, 10 MHz Precision ReferenceWith Sine and Logic Outputs
ITS-6200
The ITS-6200 is a versatile 10 MHz laboratory frequency reference useful for synchronizing test instruments to a common standard. Eight outputs are provided, each which can be configured independently as sinewave or logic level square-wave signals. Additionally, CMOS logic levels can be set for 5V, 3.3V, or 2.5V logic family compatibility. A 10 MHz reference input is provided to phase lock the ITS-6200 to an external reference, such as a GPS or Rubidium standard, or cascade multiple ITS-6200 units for additional outputs. The low phase noise and high stability OCXO within the ITS-6200 is suitable for the most demanding applications, whether free-running or phase locked. The compact size and low power consumption makes the instrument highly portable and suitable for AC-powered operation in the lab or battery operation in mobile or field applications.
-
product
Ultra-compact Digital Panel Controller
CA2
Panasonic Industrial Devices Sales Company of America
Panasonic's Ultra-Compact Digital Panel Controller CA2 offers convenient functions such as, auto referencing and scaling packed in a small body.
-
product
High Power Programmable AC Source
61610
Chroma Systems Solutions, Inc.
Power Rating:61511/61611: 12KVA61512/61612: 18KVAVoltage Range: 0-150V/0-300V / AutoConfigurations with input voltage of 220V or 480VFrequency: DC, 15Hz-1500HzSingle-phase or three-phase output selectableProgrammable slew rate setting for changing voltage and frequencyProgrammable voltage and current limitHigh output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlTTL signal which indicates output transientComprehensive measurement capability, including current harmonicsAnalog programmable interfacesRemote interface: GPIB, RS-232, USB and EthernetCapable of delivering power output up to 90KVA by implementing Master-slave parallel operation
-
product
High-Reliability Voltage Controlled Oscillators
16 Models with Frequency Bands ranging from 10 MHz to 4350 MHz. 0.5" Hermetically Sealed Surface Mount Package. 50 Ohm Internal Matching. Designed to meet MIL-STD-883 and MIL-STD-202 Test Conditions. Wide Voltage Tuning Range from 0.5V to 20V. Phase Noise as low as -120 dBc/Hz @ 10 KHz offset. 2nd Harmonics as low as -25 dBc. RoHS and REACH Compliant. All models are EAR99. These products are used in military electronics, SATCOM, test and measurement and wireless communications.
-
product
Controlled Fastening Tools
When it comes to Controlled Fastening Tools AIMCO has a wide selection of high-quality DC nutrunners, electric and pneumatic pulse tools, tool controllers and monitors and more. We'll help you find the perfect tools to get the job done right.
-
product
Miniature Pressure Controller
VSO®-EP
Parker’s VSO- Electronic pressure control unit is specifically designed for precision gas and microfluidic flow control
-
product
PXI Programmable Load Resistor Modules
Pickering's PXI programmable load modules offer a solution to applications requiring higher power handling capabilities, up to 15W in a single PXI slot. High Power Potentiometers can easily be formed by using two channels of Programmable Load Resistors in series, using the unconnected terminals as the A and B connections and the link between the two channels as the wiper connection.
-
product
Voltage Control Phase Shifter
RF Lambda’s voltage control phase shifters use an analog control voltage to vary the phase of an RF signal. They are available in a variety of frequencies and overall phase shift ranges. Hermetically sealed options are available upon request.
-
product
GPIB-RS232, Instrument Control Device - Swiss 220VAC
779732-02
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a … talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
Railway Motion Control Unit
RMCU
The Railway Motion Control Unit – RMCU is a high-performance strapdown system developed for Railway applications to determine the absolute orientation (Heading, Pitch, and Roll) and motion parameters (Angular Rates and Linear Accelerations) for any Railway Platforms on which it is mounted. Orientation is determined with high accuracy for both motionless and dynamic applications.
-
product
Programmable Power Supplies
Genesys™
The Genesys™ series sets the standard for flexible, reliable, AC-DC power systems in OEM, Industrial and Laboratory applications with the highest power density in 1U, 2U or 3U sizes at a competitive price.
-
product
Temperature/Process Controller
32DZ
The Model 32DZ Temperature/Process Controls set a new standard in 1/32 DIN power, flexibility, and value. Love Controls is proud to be the creator of the world?s first dual zone control in the 1/32 DIN size.
-
product
X-Flow Mass Flow Controller
The Parker X-Flow™ is a simplified mass flow controller for your instrument, lab or process needs. Fast, Reliable and Repeatable performance designed for OEM, Laboratory, or Process flow control instrumentation
-
product
PCI Precision Resistor Card 9-Channel, 1Ω To 62.1Ω
50-297-111
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Crossing Control Bypass Switch
XCBS-DL
The XCBS-DL is permanently wired into each crossing warning system, and can be configured with either a removable or non-removable bypass key. Simply connect the track connection harness to the designated track connection terminals. To prevent unnecessary operation of the crossing warning system, insert the key and select "bypass", rotate the knife switch to "bypass" and the crossing is disabled. When in the "bypass" position, a Dummy Track Load is connected to the track wire connections in parallel with the rails and the crossing approaches are shorted, preventing unnecessary activation when track equipment is working in the crossing approach circuit. The opening of one track lead may be desired to prevent unnecessary activation with intermittent shunting on the crossing approaches close to the crossing.
-
product
6U I7 PXI Controller
GX7927 Series
The GX7927 is a Single Board Computer (SBC) that features the high performance, highly integrated Core i7 processor platform from Intel. Core i7 offers an integrated graphics and memory controller plus dual core processing, operating at speeds up to 2.53 GHz. Coupled with the Mobile Intel QM57 Express Chipset, the GX7927 provides an unmatched level of I/O bandwidth for both onboard and off-board functions. The module is supplied with 4 GB of DDR3 SDRAM and 16 GB of NAND Flash memory. Both standard and extended temperture operation range versions are available.
-
product
PXI 2.5W Programmable Resistor Module, 4-Channel, 2Ω to 102kΩ
40-251-034
The 40-251-034 is a programmable resistor module with 4 channels which can be set between 2Ω and 102kΩ with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Powerful In-Circuit Production Flash Programmer
CYCLONE FX
P&E Microcomputer Systems' Cyclone FX programmer is is a powerful in-circuit, stand-alone programmer that supports a wide range of ARM Cortex and NXP® processor families. It's a versatile tool that offers on-board storage of programming images, provides power to the target, supports manual or automated programming, and has an easy-to-use touchscreen interface. Programming may be launched by a single button press without a PC or automatically from a PC via the automated control SDK. The Cyclone may also be used as a debug probe during development.
-
product
Dust Collector Timer Controller
DCT1000DC
Simplify your on-demand cleaning requirements with the Series DCT1000DC Dust Collector Timer Controller. Relying on one timer board for on demand and continuous cleaning applications, the DCT1000DC eliminates external devices such as pressure switches, relays and timers.
-
product
PCI Resistor Card 2-Channel 1.5 Ohm To 1.02k Ohm With SPDT
50-293-121
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
