Product

Occlusal Analysis with BiteForce DynamicsTM

T-Scan

-

Tekscan, Inc.

T-Scan - Tekscan, Inc.

The T-Scan is a diagnostic device that measures relative biting forces, including occlusal force, timing and location and is an ideal complementor to articulating paper. The technology was invented by Dr. William Maness in 1987 at Tufts University and M.I.T.

Product

ICT Probes

Merica Serirs- MP175

-

Merica Technology Ltd

Merica Serirs- MP175 - Merica Technology Ltd

Minimum Center: 1.91mm (75mil)Current Rating: 3amps, continuousContact Resistance: 40milliohmsMounting Holes Size: 1.35Full Stroke: 6.40mmRated Stroke:4.30mmSpring Force: 203gf (7.2oz)/227gf(8oz)

Product

Temperature Forcing System

ETF-SERIES

-

Envisys Technologies

ETF-SERIES - Envisys Technologies

Precise Temperature Accuracies with Reliable Test Results Temperature Limits: -40/-60 °C to 30 °C Temperature Accuracies: ±2-3°C Temperature Rate of Change: 20-25 deg /min (Non-linear) Maintenance Free Access to The System Self-Sufficient System Compact with small footprints suitable for any space constraint laboratories Low decibel system Suitable for testing electronic chips / devices Environmentally friendly refrigerants Efficient heating Microprocessor based single set point PID temperature controller with data logging Flexible hose up to 2.5-3.0m Interchangeable heads according to chip size. Inbuilt electrical control panel with switchgear system

Product

Crypto Devices

-

Rohde & Schwarz GmbH & Co. KG

Rohde & Schwarz GmbH & Co. KG

Confidential communications are essential to armed forces and government authorities. The Rohde & Schwarz crypto devices provide secure end-to-end encryption for the secure transmission of sensitive information over public communications networks or radio transmissions. Rohde & Schwarz crypto devices are interoperable with HF/VHF/UHF radios, satellite communications and line transmission equipment. They can encrypt and decrypt voice and data communications at the highest security levels. The crypto devices are ideal for stationary and mobile platforms in rugged terrain and in naval and airborne environments.

Product

Test Contactor/Probe Head

Atlas

-

Cohu, Inc.

Atlas - Cohu, Inc.

QuadTech™ probe solution with cruciform tip strength that stands up to lateral force without bending, plus an enhanced compliance window to accommodate package stack height tolerance.Atlas™ test contactor offers electrical performance that allows the customer to test to the true performance of the device. Atlas WLCSP test contactors achieve mechanical reliability with a rigid “cruciform” tip applied to Cohu’s QuadTech flat probe technology. The Atlas offers a short electrical path, with lower capacitance and inductance, that is ideal for functional and AC parametric testing of WLCSP devices that require high system bandwidth and throughput gains in large multisite test applications.

Product

Microscopes

-

PacketMicro Inc.

PacketMicro Inc.

A digital or traditional optical microscope can help engineers check on their high-speed probing activities much more easily. It will assure the probe tips will touch on the right contact(s), with correct contact angle and right amount of force. We use both digital and optical microscopes in our own lab. The information in this page is to help you choose a microscope best suits you.

Product

1 N Clip Grips

-

Shimadzu Corp.

Shimadzu Corp.

These very low force 1 N (0.22 lbf) clip grips are for tensile testing fibers, tapes, and other similar shaped specimens. They are designed for use with 50 N (11 lbf) and below load cells.

Product

Pressure Measurement Accessories

-

Omega Engineering, Inc

Omega Engineering, Inc

Pressure subbers, connector bushings, grommets, pipe and tube fittings, tube by length, pressure cooling element, pressure and force cables and connectors, air line lubricators, and air filters.

Product

Data Acquisition Systems & Data Loggers

-

imc Test & Measurement GmbH

imc Test & Measurement GmbH

Whether it’s in a vehicle, on a test stand or monitoring equipment and machinery - imc data acquisition systems are easy to operate and will help you become more productive and profitable. Our products are suited for work in mechanical and mechatronic applications. They handle up to 100 kHz per channel, are compatible with almost all signal sources and sensors, and can measure nearly all physical quantities such as pressure, force, speed, vibration, noise, temperature, voltage and current. The spectrum of imc data acquisition systems ranges from simple data acquisition via integrated real-time calculations, to the integration of models and complete automation of test stands.

Product

Rock Mechanics

ROCK3D

-

PASI srl

ROCK3D - PASI srl

ROCK3D is a program for stability analysis of removable blocks on planar rock slopes. It identifies and analyses all the blocks that have formed under each kinematic mode. Once the geometry of the rock blocks has been identified, the bolt forces necessary to reach a required safety factor are calculated.

Product

EMC-Gasketed Front Panels

-

VECTOR Electronics and Technology, Inc.

VECTOR Electronics and Technology, Inc.

EMC Front panels are designed to mount 3U, 6U and 9U Eurocard size PCBs to front panels. Applications with high connector pin counts, where high insertion/extraction force needed. They are fitted with EMC gasket that interfaces with adjacent panels to create RFI shield and does not snag when adjacent cards are extracted.

Product

Load Cells

-

VPG Transducers

VPG Transducers

The heart of each weighing system is a load cell. Load cells are mechanical components which act as force sensors by employing strain gages to provide an electrical output proportional to the applied force. Typically the electrical output is either analog (voltage or current) or digital. Load cells have specific mechanical packaging and sensing orientation to fit into electronic scales, and testing and monitoring systems. Load cells can be used for tension, compression, and/or shear measurement.

Product

Portable Tensile Tester

SG-L08C

-

Jinge Testing Machine Co.,Ltd

SG-L08C - Jinge Testing Machine Co.,Ltd

Digital Compress and Tensile testing machine.It's appropriate to testing the resistant properties of all sorts of materials such as tensile force, compression, tearing force, peel force, adhesive force, etc.

Product

General Purpose Quartz Force Sensors

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

General purpose force sensors are offered in either stud or axial mounted configurations. They are internally pre-loaded and can be used for dynamic compression, tension, and impact force measurements. Tapped mount­ing holes on both ends of the radial connector style support link, platform, integrated link, and free-standing installations. The axial mounted type offers protection of the electrical connector and sensor cable from potential damage during drop testing and in free-standing installations. Supplied impact caps facilitate impact and drop force measurements.

Product

Modeling Capacitors, Inductors, Insulators, Coils, Motors, and Sensors

AC/DC Module

-

COMSOL, Inc.

AC/DC Module - COMSOL, Inc.

The AC/DC Module is used for simulating electric, magnetic, and electromagnetic fields in static and low-frequency applications. Typical applications include capacitors, inductors, insulators, coils, motors, actuators, and sensors, with dedicated tools for extracting parameters such as resistance, capacitance, inductance, impedance, force, and torque.

Product

Exchangeable Test Fixture

MA 2112/D/H/S-7

-

INGUN Prüfmittelbau GmbH

MA 2112/D/H/S-7 - INGUN Prüfmittelbau GmbH

Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 11,30 kg

Product

Digital Force Gauge

-

Nippon Avionics Co.,Ltd.

Nippon Avionics Co.,Ltd.

*Compact and light weight*3-way power supply*Display hold function is equipped*Easy zero adjustment function*Automatic recognition of the type of sensor*Judgment function (Hi&Low) is equipped

Product

Cord Flexing Test Set Up For Hair Dryer and Hair Straightner

-

SCR ELEKTRONIKS PVT. LTD.

SCR ELEKTRONIKS PVT. LTD.

SCR Elektroniks make CORD FLEXING TEST SET UP FOR HAIR DRYER & HAIR STRAIGHTENER is used to test the Electrical accessories / appliances for their mechanical strength. Operate appliances Hair dryer or Hair straightener at rate voltage. Position appliances swivel with connection with major axis horizontal ,supply cord hanging vertically with 1N pull force. Rotate the appliance around its major axis, Clockwise & Anti-clockwise. Frequency is 10 turns in one minute.

Product

Thermal Management

-

AMS Technologies AG

AMS Technologies AG

Our air cooling components dissipating heat to the ambient air comprise high-performance heat sinks, general purpose DC fans and AC fans for forced air ventilation, as well as filter fans with exchangeable exhaust filter inserts that ensure clean and reliable air exchange in cabinets.

Product

Spring

-

Com-Ten Industries

Com-Ten Industries

Our Springtest range of spring testers are designed to check and measure the force of all types of spring: compression, tension, etc., simply and accurately.

Product

Precision Positioning stage

N-661

-

Physik Instrumente GmbH & Co. KG

N-661 - Physik Instrumente GmbH & Co. KG

Miniature Linear Stage with NEXACT Drive Travel Range 20 mm Self Locking at Rest, no Heat Generation, no Servo Dither Compact Design: 70 x 50 x 20 mm Zero-Wear Piezo Stepping Drive, Ideal for Micro- and Nano-Manipulation Integrated Linear Encoder Option for Highest Accuracy with 20 nm Resolution Two Operating Modes: Continuous Stepping Mode and Continuously Variable, High-Dynamics Analog Mode for 30 pm Resolution** Up to 10 N Force Generation

Product

IEC60335 Test Probe 11

CX-11

-

Shenzhen Chuangxin Instruments Co., Ltd.

CX-11 - Shenzhen Chuangxin Instruments Co., Ltd.

Test Probe 11 This Unjointed Finger Probe is made for forceful insertion where the flexibility of the Jointed Finger Probe would be difficult.

Product

Spring Contact Probes

-

Merica Technology Ltd

Merica Technology Ltd

Spring Contact Probes - Test Center: 50 - 100 milsCurrent Rating: 3 - 5 ampsContact Resistance: 30 - 50 milliohmsSpring Force: 113 - 312 gf (4-11 oz)