Product

Electrodynamic Shaker Systems

-

MB Dynamics Inc

MB Dynamics Inc

Electrodynamic shaker systems and amplifiers from MB Dynamics help to support a wide range of general-purpose vibration test requirements. The electrodynamic shaker systems are offered in a variety of force ranges, from 100N (25 lbf) to 22kN (5,000 lbf). The innovative design of MB Dynamics PM-Series electrodynamic shakers incorporates permanent magnet technology and the voice coil principle to create vibration. These heavy-duty electrodynamic shakers feature a robust design for maximum reliability, with end-users reporting a useful service life of 10, 25 or even 40 years! The shakers come in five unique sizes, with peak sine force ratings of 100 N, 200 N, 500 N, 1000 N and 2000 N; or, 25 lbf, 50 lbf, 100 lbf, 250 lbf and 500 lbf. The MB Dynamics C40HP electrodynamic shaker outputs 22 kN or 5,000 lbf peak. The C40HP is a part of the legacy C-Series of shakers, which have served as the foundation for today’s modern electrodynamic vibration test equipment industry.

Product

Elevated 1.68 (48.00) - 7.00 (198.00) High Performance Lead Free Probe

LFRE-1H-7

-

ECT

LFRE-1H-7 - ECT

Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02

Product

Push Pull Force Gauge Meter

NK-10

-

Shenzhen Chuangxin Instruments Co., Ltd.

NK-10 - Shenzhen Chuangxin Instruments Co., Ltd.

*This push pull force gauge Easy to be operated and can be  installed with all kinds of test stands and clamps.*Peak holding function and continuous.*One year free maintenance.*Compact and artistic packing, easy to transit and stock.*Two kind of unit dual show at the same time,*don't need unit conversion. *NK Series: Newton and Kilogram dual unit; *NLB Series: Newton and Pound dual unit; *ALB: Pound and Kilogram dual unit.*Needle indicates, easy to read, high accuracy.

Product

High Force Large Area Bond Tester

Sigma HF

-

Xyztec

Sigma HF - Xyztec

- For high force and large area- Typically for IGBT, power modules and batteries up to 1000 kgf- High axis speed- Deep access up to 80 mm- SEMI S2 safety cabinet with visual feedback- Flexible positioning of multiple work holders

Product

Finite Element Analysis

-

Response Dynamics Vibration Engineering, Inc.

Response Dynamics Vibration Engineering, Inc.

An understanding of structural dynamics is very important to sound Finite Element Analysis (FEA). We have been performing FEA analysis for over 30 years and in most cases we have used experimental data to guide our modeling. While our engineers have had undergraduate and graduate courses in FEA, it is the years of modeling and analysis of existing structures that has taught us the most by forcing a thoughtful analysis of the key structural dynamics and then going though the process of making adjustments to boundary conditions, expanding the dynamics of the model in places, and making simplifications and approximations where possible.

Product

Real-world Dynamics

-

Physical Property Testers Group

Physical Property Testers Group

Dynamics is the study of the motion of objects and the forces responsible for that motion. It is a branch of classical mechanics, involving primarily Newton's laws of motion.

Product

400W to 600W - Single Output

CUS600M Series

-

TDK-Lambda Corp.

CUS600M Series - TDK-Lambda Corp.

*400W (600W Peak) Convection Cooled*600W with Forced Air*Medical Certifications (2xMOPP)*Class B Conducted and Radiated EMI*Suitable for Class I and Class II installations*Compact 3 x 5 x 1.46" size

Product

Creep and Stress Rupture Tester

QualiCreep Series

-

Qualitest International Inc.

QualiCreep Series - Qualitest International Inc.

Qualitest Creep and Stress Rupture Tester - QualiCreep Series is mainly designed to perform Creep and Stress Rupture testing of a wide variety of materials to both standard and customized specifications such as ASTM E139, ISO 204, ISO/R 206 and similar international standards. These machines are capable of covering the determination of the amount of deformation as a function of time (creep test) and the measurement of the time for fracture to occur when sufficient force is present (rupture test) for materials when under constant tensile forces at constant temperature. Qualitest offers three models electronic high temperature creep-testing machine with full closed-loop servo-control in capacities from 10kN to 500kN.

Product

Emergency Beacons

-

Astronics Corporation

Astronics Corporation

Emergency beacons that utilize satellites to alert search and rescue forces of a distress location.

Product

Material Testing & Physical Testing

-

Cole-Parmer Instrument

Cole-Parmer Instrument

Meeting the specifications put out by testing equipment manufacturers is critical when conducting quality control testing. We carry a wide variety of materials testing and physical testing products that are ideal for quality control testing along with research applications, letting you evaluate and test materials such as plastics, coatings, and chemicals. Physical properties testing products range from force and torque instruments, to hardness and thickness gauges, to viscometers and spectrometers.

Product

Measurement Hardware

-

imc Test & Measurement GmbH

imc Test & Measurement GmbH

Whether it’s in a vehicle, on a test stand or monitoring equipment and machinery - imc data acquisition systems are easy to operate and will help you become more productive and profitable. Our products are suited for work in mechanical and mechatronic applications. They handle up to 100 kHz per channel, are compatible with almost all signal sources and sensors, and can measure nearly all physical quantities such as pressure, force, speed, vibration, noise, temperature, voltage and current. The spectrum of imc data acquisition systems ranges from simple data acquisition via integrated real-time calculations, to the integration of models and complete automation of test stands.

Product

Grips For Shouldered-Rod Specimens

-

Shimadzu Corp.

Shimadzu Corp.

Introduction of specimens into the grips is straightforward and the design of these grips is such that during testing the specimen and grips exert opposite forces on each other, holding the specimen tightly in the grips.

Product

Piezo-Electric Measurement Trainer Module

-

Unitech Scales And Measurements Pvt. Ltd

Unitech Scales And Measurements Pvt. Ltd

PiezoElectric Trainer comprises of piezoelectric crystal mounted inside housing and fitted on a base plate. Digital indicator is supplied to indicate the vibrational force.

Product

Material Test Machines

-

Sanwood Environmental Chambers Co ., Ltd.

Sanwood Environmental Chambers Co ., Ltd.

Sanwood Universal Test Machines, UTM, are widely use for different material testing, like semi-product & finished product made of rubber, plastic, metal, nylon, non-woven fabrics, textile, tape, polyfoam, waterproof materials, wire, cable, etc. With different test jigs or fixtures, the UTM can run the tensile, compression, shearing foce, adhesion, peeling force, tear strength, fatigue, etc test according to GB, CNS, ASTM, ISO, DIN, JIS, EN test standards.

Product

Extender

3690

-

VECTOR Electronics and Technology, Inc.

3690 - VECTOR Electronics and Technology, Inc.

Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.

Product

Spring Loaded Contacts

-

Harwin Plc

Harwin Plc

ATE Probes, Pogo pins and Contact Pads. Gold-plated, spring-loaded, capable of thousands of cycles. Probes for Automated Test Equipment (ATE). Various height SMT contact pins. Flat SMT contact pads. Spring loaded contacts consist of a plunger (or head), barrel (or body), and a fully encapsulated fine spring, to provide the spring force required to maintain positive contact. All have a high durability, exceeding 10,000 mating cycles.

Product

Hardware/Software for Increased Production

VibLink & NavLink

-

Seismic Source Co.

VibLink & NavLink - Seismic Source Co.

The VibLink system - Each vibrator, plus the central recorder, is equipped with a VibLink module. The VibLink module uses advanced TDMA techniques to multiplex seven vibrators and the doghouse on one radio channel. And does this all in one second windows. With additional Vibrators, additional seconds are added. The Universal Encoder 3 uses its time slot to send out status updates and request PSS/PFS data. Each Force 3 controller uses its time slot to send out its location, status, and QC Information.

Product

Fatigue Rated Low Profile Cells

-

PCB Piezotronics, Inc.

PCB Piezotronics, Inc.

Fatigue rated load cells are specifically designed for component durability and fatigue test machines where highly cyclical loading is present. These rugged load cells are extremely resistant to extraneous bending and side loading forces. They are used for material testing, component life cycle testing and structural testing. All fatigue rated load cells are guaranteed against fatigue failure for 100 million fully reversed cycles.

Product

Semiconductor Device Parameter Analyzer/Semiconductor Characterization System Mainframe

B1500A

-

Keysight Technologies

B1500A - Keysight Technologies

Current-voltage (IV) measurement capabilities of spot, sweep, sampling and pulse measurement in the range of 0.1 fA - 1 A / 0.5 V - 200 VAC capacitance measurement in multi frequency from 1 kHz to 5 MHz and Quasi-Static Capacitance-Voltage (QS-CV) measurement capabilitiesAdvanced pulsed IV and ultra-fast IV measurement capability from minimum 5 ns sampling interval (200 MSa/s)Up to 40 V high voltage pulse forcing for non-volatile memory evaluation

Product

Digital Macro Vickers Hardness Tester w/ Printer

900-398

-

Phase II Plus

900-398 - Phase II Plus

The 900-398 Vickers Hardness Tester is engineered to produce a clear indentation and a more precise measurement. By means of a load cell, closed circuit system for control, the CPU controls testing force to load/dwell/unload, allowing for the highest degree of accuracy. The large LCD shows the measuring methods, the testing force, the indentation length, hardness value, the dwell time of the testing force as well as the number of the measurement on its screen.

Product

Semiconductor Equipment Manufacturers

-

Integrated Dynamics Engineering

Integrated Dynamics Engineering

With shrinking process geometries, new structural elements and a major increase in substrate size, the challenges to improving process yield and overall throughput have increased exponentially. These demands drive a stringent requirement for system stability and overall immunity from internal and external forces.

Product

Force Measurement & Torque Measurement Test Stands

-

Mark-10 Corp.

Mark-10 Corp.

Mark-10 offers the industry's most extensive line of manual force measurement and torque measurement test stands. Test stands are useful in eliminating variability inherent in hand testing and can help to automate test processes. A wide range of capacities, loading methods, and configurations are available. A test stand is an integral part of a testing system, typically also comprising a force gauge or torque gauge, grips, software, and accessories.

Product

Compact Low Profile Load Cell

1000 Series

-

HITEC Sensor Solutions Inc.

1000 Series - HITEC Sensor Solutions Inc.

Compact Low Profile load cells are fully stainless steel, hermetically sealed load cells with a multi-beam internal structure, and fully integrated electronics to provide high level analog or digital outputs. This type of load cell is easy to use for measuring tension or compression loads from 200N (50lb) to 5kN (1000 lb), and is capable of rejecting side forces that would otherwise affect accuracy. This type also offers the user the ability to set the gain and offset (span and zero) electronically, to provide maximum flexibility for the user application.

Product

Compression Load Cells

-

Variohm Eurosensor Ltd

Variohm Eurosensor Ltd

A block that is designed to hold a load at one point to measure the compression. While tension load cells measure the pulling force, compression load cells measure a pushing force along a single axis.