Vibration Control
A hardware/software product that generates one or more analog drive signals that are applied to a customer's amplifier / shaker / test device for the purpose of creating a specified vibration environment at one or more points on a test device. (dataphysics.com)
See Also: Vibration Controllers, Vibration Test
-
Product
HS1760/MIL-STD-1760E XMC Network Interface Controller
XMC-1760-NIC-FP
-
Avionics Interface Technologies
Configuration Variants available: XMC-HS1760-NCNT: One NC Node and One NT Node, XMC-HS1760-NCNC: Two NC Nodes, XMC-HS1760-NTNT: Two NT Nodes - SAE AS5653-Compliant Network Controller/Network Terminal NIC - Unsolicited data path for handling Fibre Channel link service or non‐FC-AE‐1553 traffic - Supports DMA for high speed streaming of data75 Ohm single‐ended or 150 Ohm Differential coax interface – TNC connectors - Each port supports 1.0625 Gbps speed - ANSI C API interface for both NC and NT - Device driver support: Windows, Linux, & VxWorks - Quad (4) port board available on request
-
Product
Multi-Unit Controllers
-
Mosebach Manufacturing Company
Mosebach’s Multi-Unit Controllers are built to help you manage your load banks in operation – whether 10, 20 or 500 units ganged together.
-
Product
Voltage Controlled Oscillator Assembly With Heater
-
Teledyne RF & Microwave has designed a Voltage Controlled Oscillator to replace an existing application. The oscillator covers the 520 to 560 MHz frequency range. The oscillator provides +10 to +13 dBm output power. The oscillator has internal heaters designed to maintain the oscillator assembly at constant temperature. The unit operates over the 0° to 60° C temperature range with ~200 KHz frequency variation due to temperature variation.
-
Product
Walk in chamber for Complex Salt Spray Test (Temperature controllable)
-
Guangdong Bell Experiment Equipment Co.,Ltd
Walk in chamber for Complex Salt Spray Test Relevant standards requirement1. Test Object: battery pack andsystem.2. Refer GB/T4 part 5.5.2 test method, test according to GT/T2423.17 test conditions.3. The salt solution was made up with sodium chloride (chemically pure and analytically pure) and distilled or deionized water，Its concentration is (5 + 1)% (mass fraction).4. (35 ± 2) ℃, the measured pH value is between 6.5-7.2.5. Placed the test objects in the salt spray chamber for cycling test. Each cycling duration for 24h. Spray salt solution to the test object for 8 hours under the temperature of (35± 2) ℃ , remain for 16 hours. Between the forth and the fifth hour in one cycles should be according to test requirement in GB/T 28046.1-2011, test mode with 3.2.6. Total 6 cycles testing.7. Salt spray test is not necessary for the test objects being installed in passenger, luggage or cargo compartments.
-
Product
Voice System for Air Traffic Control
VCS
-
CERTIUM® VCS is a quad-redundant, IP based voice communications system that integrates perfectly into the entire CERTIUM® portfolio for safe, secure and efficient airspace operations. It combines a state-of-the-art, flexible and resilient IP based architecture with strong security mechanisms. It is flexible enough for both small towers and nationwide systems with multiple area control centers and hundreds of controller working positions. CERTIUM® VCS has advanced functions that can support remote digital tower systems or connect area control centers to virtual centers for quick and flexible transfers between centers and even countries.
-
Product
Data Acquisition & Control
-
Blue Chip Technology have been designing and manufacturing data acquisition and control boards since 1986. The current range of boards have digital and analog IO and an excellent record for reliability in the harshest of environments.
-
Product
Distribution Control
-
Schweitzer Engineering Laboratories, Inc.
SEL solutions improve distribution system reliability and efficiency with intelligent protection, monitoring, and control devices.
-
Product
All-in-one Streamer Positioning & Control
Nautilus®
-
Nautilus provides positioning as well as vertical and lateral steering in a unique node. Fully integrated with Sentinel, Nautilus is directly powered from the streamer providing a greater availability and enhanced safety with reduced number of workboat operations.
-
Product
EZ-Glider Position Control Telescoping Torque Arms
-
The position control telescoping torque arms help manufacturers detect and eliminate costly screw-fastening errors during the assembly process. Position Control telescoping torque arms are designed to reduce the risk of improperly fastened screws, ensuring that every screw is in the correctly tightened in the correct sequence. Using the EZ-Glider Position Control torque arm is like putting the eyes and ears of a quality control manager where they are needed most - right on the assembly area.The EZ-Glider Position Control telescoping torque arm consists of a torque reaction arm with encoders mounted at the base and a control box. The control box is used for programming and it tracks the axis movement by converting angle counts to the precise position of the screwdriver. The location is calculated from encoder values, allowing the operator to easily teach the torque arm a programmed sequence pattern and then use it to control the assembly process
-
Product
Intelligent Micro-Processor Control
-
AllWin Instrument Science and Technology Co., Ltd.
1. Intelligent, micro-processor control,2. LCD display, optional RS232C port,Standard PLC interface3. The max IR can be up to 10.00T
-
Product
Engine Vibration Measurement Unit
MS 1101
-
Used to check engine vibration level. The seismic transducer mounted on both engines. Used for the measurement of vibration levels for various engine rpm. Used for the measurement of amplitude on each frequency component
-
Product
MTM-IO-Serial: Software Controlled USB Hub and IO Module
-
As part of Acroname's MTM series, the MTM-IO-Serial module is a key component to manufacturing test systems for electronic devices using a standard USB 2.0 interface, serial UARTs and one or more interface voltages. The MTM-IO-Serial module features a software controlled USB hub (USB 2.0 high-speed) with four controllable channels. Each channel has switched data and 500mA current-limited power lines.
-
Product
Vibration Diagnostics System
VDS
-
The Vibration Diagnostic System (VDS) is a vibration data management system designed specifically for the machinery Predictive Maintenance (PdM) community. It harnesses the graphic display capabilities of Crystal Instruments EDM Software for the work of machinery vibration analysts.
-
Product
Multifunctional UV Control Software
UVProbe
-
UVProbe is multifunctional, easy-to-use software supplied as standard with Shimadzu UV-VIS Spectrophotometers. The UVProbe is connected to the LabSolutions system, which is known for its capabilities in complying with ER/ES regulations. Enables safe, reliable management of data.Not only can UV data be managed, but the comprehensive management of LC, GC, and FTIR data can also be accomplished.In addition, When combined with CLASS-Agent, it provides powerful support for Part 11 compatibility.
-
Product
Scienlab Emulator Control Software
SL1092A
-
The Emulator Control software can control Scienlab systems from Keysight such as the Machine Emulator and the Dynamic DC Emulator. The software also can manage both emulators combined in a test bench manually.
-
Product
Route Based Vibration Data Collector
-
The Crystal Instruments CoCo series are portable devices for vibration monitoring and predictive maintenance applications. The system consists of a CoCo analyzer and the Engineering Data Management (EDM) software. The CoCo is used to make field measurements and the EDM software in Vibration Data Collector (VDC) Mode is used to setup the CoCo hardware and define routes before field measurements, and to download data from the CoCo to analyze and archive afterwards.
-
Product
Source Phase Control
S97088B
-
The S97088B allows users to set calibrated, arbitrary phase differences between two signal sources running on the P50xxA Streamline VNAs.
-
Product
Temperature Controllers
-
Represents our dual-display solution in the basic temperature controller segment.
-
Product
Control Board for Motor, Pump & Valve
F1V04
-
Beijing SANKI Petroleum Technology Co., Ltd.
The main board issues a start signal and a low voltage signal (12v) for opening the electromagnetic valve, which are converted into strong voltage signals (220 VAC) to drive the electromagnetic valve (380 VAC) and the motor in our fuel dispensers system, thus completing the function of conversion from weak voltage power to strong voltage power. The control board circuit isolates high voltage interference signals via photoelectrical isolating components.
-
Product
PMAC Controller Software
-
PMAC Software for programming, configuration and visualization for the PMAC family of motion controllers.
-
Product
Railway Motion Control Unit
RMCU
-
The Railway Motion Control Unit – RMCU is a high-performance strapdown system developed for Railway applications to determine the absolute orientation (Heading, Pitch, and Roll) and motion parameters (Angular Rates and Linear Accelerations) for any Railway Platforms on which it is mounted. Orientation is determined with high accuracy for both motionless and dynamic applications.
-
Product
Conventional Panel-mounted Type Power Amplifier Control Unit
PAT01
-
PAT01 is a power amplifier control unit that controls timing output and reference signal test source for power amplifier.
-
Product
Horizontal Vibration Test Systems
G-3 Series
-
This series was used for the special structure of airbearing guide of inspection for Seismic Detectors andcharacterized is large displacement and high-accuracywaveform. In addition, the use of the Windows seismicdetector controller is easy to operate it.
-
Product
Dynamics & Vibration Testing
-
Vibration testing ensures that your new design will survive in its intended environment. Submitting your product for vibration testing or analysis pays for itself by reducing field return costs through improved product reliability.
-
Product
Vibrating Level Switch
TF 100 Series
-
TF-100 Series is a vibrating level switch with TF-L relay output and TF-P transistor output or with TF-T current output.This level switch is designed for reliable indication of clean liquids and light slurries. It is available with Relay, Current, and PNP outputs that can be set to indicate alarm on either high level for spill prevention, or low level for run-dry protection.
-
Product
Automated System for Identification and Control of Pharmaceutical Codes
-
The automated system for identifying pharmaceutical codes includes two scanners of the pharmaceutical code, two sensors for the presence of an object and a data processing unit (BOD). When the box or instructions are passed under the object presence sensors, the farm code is read by the corresponding scanner and the results are transmitted to the computer via the Ethernet interface. The BOD verifies the correctness of the read out farm code by comparing this code with the reference farm code set at the beginning of the system operation. If the farm code has not been read or does not match the standard, the packaging machine stops and the type of error is displayed on the indicators.
-
Product
CompactRIO Embedded Real-Time Controllers
-
CompactRIO embedded real-time controllers provide deterministic offline execution of LabVIEW applications. A wide range of controllers are presented, differing in performance and operating conditions.
-
Product
Corded & Cordless Controls
-
Reference designs and custom development controller solutions for your aircraft.
-
Product
Engine Speed Control and Measurement (Test Set A)
MS 1100
-
*Checks the parameters such as current, voltage, speed, and turbine gas temperature of 804E and 811 engines Portable instrument*Testing of Automatic engine control system and after burner control system*Simulates the temperature signal derived from the engine TGT (Temperature Gas Turbine) thermocouples*Simulates the speed signal, NL (low pressure shaft speed signal) drive from the L.P shaft Probe*Indicates the current signal to the FCU solenoid derived from the engine control amplifier*Measure the TGT and NL simulated signal at static position*Measure the signal produced by the engine TGT thermocouples*Measure the NL signal produced by the LP shaft*Measure the NH (High-pressure shaft speed) signal produced by HP shaft*Indicates the solenoid current, produced by the engine control amplifier*Indicates the solenoid voltage, produced by the engine control amplifier*Used to test engine in both static and dynamic states
-
Product
Compact Hydraulic Vibrator Force Simulator
JF Series
-
The JF Series Force Simulator was developed with the emphasis on light weight, compact size and ease-of-use as a general-purpose, compact jack for the Servopulser system. Testing systems installed with the Force Simulator can easily perform endurance, fatigue and simulation tests on small structural members and various other structural members, which helps improve the logical design and reliability of products.
