Optical Switch
Route signal transmitted through optical fiber among optical circuits.
See Also: Switches, Membrane Switch, Coaxial Switches, Crossbar, High Voltage Switching, Fiber Optic Switching, Microwave Switching
-
product
Coaxial Switch, DC to 4 GHz, SPDT, 75 Ohms
8762F
The Keysight 8762F brings a new standard of performance to 75-ohm coaxial components. Designed for ATE switching systems, the Keysight 8762F offers the performance demanded by the cable television distribution equipment and communications equipment industries. It gives the ATE system designer of telecommunications and cable distribution equipment the tools to design reliable, high performance switching interfaces. The Keysight 8762F uses a mini 75-ohm SMB connector for the coaxial interface. The mini 75-ohm SMB connector is designed to terminate RG-179 75-ohm coaxial cable. The Keysight 8762F is designed to work in virtually any system due to the range of voltage options covering 4.5 V to 30 Vdc available for activating the switch solenoids. The standard configuration of the switch includes solder terminals.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode
40-850A-314-M50
The 40/42-850A-314-M50 is a PXI/PXIe 4-channel multiplexer with MU (mini SC) connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
Switches
Teledyne Microwave Solutions (TMS) offers High Isolation Switches with low insertion loss, high 1dB compression point, high third order I.P. and fast switching speed. Our switches are designed for a wide variety of communications applications.
-
product
RS232 / RS485 / RS422 / Serial To Multi-Drop Fiber Optic Converters
Our advanced, rugged, industrial-grade, RS232 / RS485 / RS422 serial to multi-drop fiber optic converters are designed to cover large areas. These converters support up to 255 fiber nodes, and each fiber node can extend the RS232 / RS422 / RS485's distance to 3 miles (5km) for multi-mode converters and cables, or 25 miles (40km) for single-mode converters and cables. Depending on the site situation, these multi-drop fiber optic converters can be configured as a daisy-chain or a self-healing redundant ring fiber network. When configured as a ring fiber network, the built-in self-healing feature allows the data to be transmitted clockwise or counterclockwise; therefore, failure of any individual converter will not affect other devices located on the same fiber ring, making the entire data network more robust and reliable. These multi-drop fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options of multi-mode and single-mode, and ST, SC, and FC connectors.
-
product
Close Contact Confirmation Switch
HPS/MHPS/UHPS
High precision needle mechanism enables highly accurate detection such as contact confirmation.In addition, various special nozzles can be applied to various position detections.
-
product
Single 4 Ch Fiber Optic MUX SC/PC
40-810-214
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or mult- mode fiber.A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
product
1310nm Direct Modulated Optical Transmitter
ONT-8600AG
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai 1310nm direct modulation optical transmitter, adopts high linearity DFB laser of famous brand in the world, and builds-in perfect pre-distortion adjustment circuit and laser APC, ATC closed loop control circuit. All the operating parameters are controlled by microprocessor, and the LCD screen on the front panel can display relative operating status and the fault information. Guangtai ONT-8600AG series direct modulation optical transmitter adds AGC function on the base of ONT-8600AF reliable type. It is a universal AGC optical transmitter.
-
product
Special Fiber Optics
Shanghai Tarluz Telecom Tech Co., LTD
Optical fibers which have at least one special property, distinguishing them from standard fibers.
-
product
RS422 Mode SI-module With Optical Isolation And RTS/CTS
MX422-PEP
RS422 mode SI-module with optical isolation and RTS/CTS
-
product
Near-field Scanning Optical Microscope
NSOM
Near-field Scanning Optical Microscope (NSOM) is a versatile tool for nano-characterization and nanomanufacturing.Conventional microscopes have fundamentally limited resolution due to diffraction, but there is no such restriction for near-field interactions, that is why near-field microscopy is becoming one of the most important techniques for nano-science.
-
product
Handheld Fiber Optical Power Meter
3208
Anfkom International Co.,Limited
3208 handheld optical power meter is a compact and an easy-to-use testing instrument for optical fiber networks, which can be used for absolute optical power measurements as well as for relative loss measurements in optical fibers. It features ingenious appearance, wide range of power measurement, high accuracy and user self-calibration function with high performance-to-price ratio.
-
product
Switch Probes
A Switch Probe is a spring contact probe and receptacle combination that is normally open, and after a designated travel the switch probe closes. The most common use for switch probes is in the cable harness testing industry. The switch probe is used to verify the correct location of a terminal in a connector while checking the retention force as well. Switch probes also verify the presence of nonconductive components such as caps for connectors or devices on a circuit board. Smiths Interconnect offers three standard sizes of switch probes.
-
product
Zinc Diecast Body Vacuum Switch
P119V
The P119V Zinc Diecast Body Vacuum Switches are the inexpensive version of the P117V and recommended for indoor OEM use. It is commonly used in the medical field and as a safety switch in numerous applications. The compact nature of these switches make them ideal for tight spaces.
-
product
SP8T RF Pin Diode Switches To 12 GHz
Pulsar Microwave manufactures 8-way absorptive and reflective RF switches in single-pole 8-throw configuration. They fulfill broadband and narrowband requirements from 40 MHz to 12 GHz and handle 200 milliwatts input power. The SP8T switches have an isolation of 60 dB and switching time of 100 ns. Most models specify 1.6:1 or better VSWR at all ports. The SP8T switches operate on a power supply of +/- 5VDC and switching control is 0-5 TTL logic. The unit comes standard with SMA female connectors. Options for control are line drivers and decoders.
-
product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 3-Channel
40-203-001
The 40-203-001 (PXI) and 42-203-001 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 3 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
product
Low Passive Intermodulation (PIM) Coaxial Switches
Low Passive Intermodulation (PIM) Coaxial Switches
-
product
High Static Stiffness Optical Breadboards
5700 Series
They feature a lightweight precision formed steel honeycomb construction with 3/16″ ferromagnetic stainless steel top skin and 3/16″ low carbon steel bottom skin with a black polyurethane finish.
-
product
CATV & SAT IF Optical Receiver Module
MRS-26D
Hangzhou Huatai Optic Tech. Co., Ltd.
*Ultra low noise push-pull technology *Band width of 2.7 GHz* 46dB CNR (typ.) for NISC with OMI = 4% at –8dBm optical input power @ 1550nm* 20dBmV RF output level (-5dBm,1550nm,OMI=4%)* Very low intermodulations *Low power consumption *Small package with single-mode fiber pigtail *Integrated optical demultiplexer (WDM filer) for RF overlay applications *Monitor voltage output and output disable input
-
product
Data Acquisition Switch System
M300
No matter the product performance test in the R & D stage or the automatic test in the production process, for the application of multiple test points and multiple signal measurement, the M300 series data acquisition / switch system with modular structure combines the precise measurement function with the flexible signal connection function, and can provide a wealth of test measurement solutions.
-
product
Quad Optical Loss Test Set
KI27624-INGAAS
A Quad Optical Loss Test Set used to test power, insertion loss, continuity and faults on multimode and single mode fiber optic systems at 850 / 1300 nm & 1310 / 1550 nm. In a small package, it provides a powerful optical multi-meter style solution to improve test flexibility and productivity.
-
product
Single Board Source/Meter/Switch
SMSU
SMSU Series SourceMeterSwitch Unit (SMSU), introduced by SW Link Ltd, is single-channel voltage/current sourcing, 4X6 switch matrix and measurement instruments. Each Series 100 SMSU instrument tightly integrates highly accurate stable DC power source and a true instrument-grade programmable gain amplifier and 18bits ADC on a 100x100mm PCBs. It can output up to 20V, sub-uA to 1A current to device under test (DUT)
-
product
Optical Power Meter
FiberLink 6650
The Fiberlink 6650 Optical Power Meter is a high accuracy, high resolution, microprocessor controlled optical power meter. It has a wide 65 dB dynamic range, and is calibrated to measure 850, 1300, 1310, and 1550nm, making it ideal for both singlemode and multimode fiber testing, as well as 1490nm for measurement of FTTx PON networks.
-
product
Handheld Optical Power Meter
JW3402
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3402 Optical Power Meter is a highly cost-effective portable power meter and it’s newly launched by the Joinwit Company. It can be used for the optical power measurement within the wavelength 800~1700nm. JW3402 also has a wide measurement range which is more than 70dB. It’s designed with the common wavelength calibration points, such as 850nm, 1300nm, 1310nm, 1490nm, 1550nm, 1625nm. The instrument is widely used in fiber-optic link construction, testing and maintenance.
-
product
Optical Transmitter
ST1013-10mW
Hangzhou Softel Optic Co., Ltd.
*Designed for FTTH(Fiber To The Home)Networks *Excellent Linearity and flatness *Single-mode fiber high return loss *Using GaAs amplifier active devices *Ultra low noise technology *Using DFB coaxial small package laser *Smaller size and easier install *Red-LED for power indication
-
product
Fiber Optic Type Chemical Concentration Monitor
CS-600F
The CS-600F achieves a higher level of functionality best suited for manufacturing, such as the ability to perform in-line measurement of high temperature chemical solutions in various applications, stable operation for reduced downtime, and compact size for improved space productivity in order to meet the precise chemical solution concentration management required in leading-edge semiconductor wet process.
-
product
Optical Parametric Oscillators
Our optical parametric oscillators are the most advanced in the industry, with leading technology plus a range of options to suit every system and customer need.
-
product
Enclosed Optical Encoders
Featuring Renishaw's proven absolute encoder technology within an exceptionally robust enclosed design, FORTiS encoders deliver high performance measurement in the harshest of environments, offering significant benefits over conventional systems.
-
product
MICROWAVE SWITCHING DIODES FROM 1 to 40 GHz
Insight Product Company offers Microwave Switching Diodes with switching time up to 3 nsec and operating in frequency range from 1 to 40 GHz. The p+ -n - n+ silicon spackage-less switching diodes are designed to be used in microwave switching devices, phase changers, modulators, microwave attenuators - parts of hybrid microcircuits that provide capsulation and protection against ambient action.
-
product
28/45 GHz Single Optical Channel DCA-M with Option CDR
N1092A
High accuracy, low cost solution for optical waveform analysis including solutions for 8.4 through 64 GBaud, very low noise and jitter, fast sampling rates for high throughput, and integrated clock recovery available.





























